Bug 5738

Most recent kernel where this bug did not occur:
Distribution: Debian stable
Hardware Environment: 
Supermicro P8SCT-> http://supermicro.com/products/motherboard/P4/E7221/P8SCT.cfm
(uses intel E7221/ahci for SATA controller).  Hot-swap raid cage.  Three SATA
ports in use.  Also have two MegaRAID SATA 150-6 onboard, one in PCI-X slot.

Problem Description:
This box will run stable, but at inconsistent times lock up.  After hooking up
serial console, we discovered the problem.

FYI, we have three different motherboards from Supermicro, and they all exhibit
the same issue... it is unlikely a fault with our specific hardware.

It is easiest to trigger this bug (not certain if this is the only way) when
running software raid, two drives, in stripe mode.  Many times this
configuration will cause no isses, other times I get this:

  ata2: handling error/timeout
ata2: port reset, p_is 0 is 0 pis 0 cmd 4017 tf d0 ss 113 se 0
ata2: status=0x50 { DriveReady SeekComplete }
sdb: Current: sense key=0x0
    ASC=0x0 ASCQ=0x0
Assertion failed! qc->flags &
ATA_QCFLAG_ACTIVE,drivers/scsi/libata-core.c,ata_qc_complete,line=351
3
------------[ cut here ]------------
kernel BUG at drivers/scsi/scsi.c:295!
invalid operand: 0000 [#1]
Modules linked in:
CPU:    0
EIP:    0060:[<c02d54c1>]    Not tainted VLI
EFLAGS: 00010046   (2.6.15-rc2)
EIP is at scsi_put_command+0x8b/0x95
eax: f7f69d90   ebx: f7f98680   ecx: f7f9868c   edx: f7f9868c
esi: f7f8c000   edi: 00000296   ebp: f7f69c00   esp: f7ff7c0c
ds: 007b   es: 007b   ss: 0068
Process scsi_eh_3 (pid: 858, threadinfo=f7ff6000 task=f7ea9030)
Stack: f7f69df8 c0225720 f7f98680 f7f69d90 f7f62dfc f7f62dfc c02d9cdf f7f98680
       efadda7c f7f98680 00000282 c02d9e05 f7f98680 00000001 00000000 efadda7c
       f7f98680 00000000 f7f98680 c02da0df f7f98680 00000001 00000000 00000001
Call Trace:
 [<c0225720>] kobject_get+0x1a/0x24
 [<c02d9cdf>] scsi_next_command+0x2f/0x4f
 [<c02d9e05>] scsi_end_request+0xc4/0xd6
 [<c02da0df>] scsi_io_completion+0x19a/0x41e
 [<c036448e>] sd_rw_intr+0xc6/0x26d
 [<c02d5bc7>] scsi_finish_command+0x82/0xa2
 [<c035b708>] ata_scsi_qc_complete+0x47/0x8d
 [<c0358eb0>] ata_qc_complete+0x40/0xc6
 [<c035cfd9>] ahci_interrupt+0x107/0x1e3
 [<c0112089>] activate_task+0x6d/0x80
 [<c01321d1>] handle_IRQ_event+0x2e/0x64
 [<c013225a>] __do_IRQ+0x53/0xa5
 [<c011d606>] update_process_times+0x7b/0x106
 [<c010455c>] do_IRQ+0x19/0x24
 [<c0102fda>] common_interrupt+0x1a/0x20
 [<c0119bc3>] __do_softirq+0x2f/0x8a
 [<c0119c44>] do_softirq+0x26/0x28
 [<c0104561>] do_IRQ+0x1e/0x24
 [<c0102fda>] common_interrupt+0x1a/0x20
 [<c02daa73>] scsi_request_fn+0x1a9/0x2c2
 [<c0218c27>] blk_run_queue+0x3a/0x3c
 [<c02d9ce7>] scsi_next_command+0x37/0x4f
 [<c02d9e05>] scsi_end_request+0xc4/0xd6
 [<c02da0df>] scsi_io_completion+0x19a/0x41e
 [<c036448e>] sd_rw_intr+0xc6/0x26d
 [<c02d5bc7>] scsi_finish_command+0x82/0xa2
 [<c035b708>] ata_scsi_qc_complete+0x47/0x8d
 [<c0358eb0>] ata_qc_complete+0x40/0xc6
 [<c035cea6>] ahci_eng_timeout+0x85/0xb0
 [<c02d91fb>] scsi_error_handler+0x0/0x99
 [<c035af32>] ata_scsi_error+0x1a/0x31
 [<c02d925a>] scsi_error_handler+0x5f/0x99
 [<c012706d>] kthread+0xb1/0xb7
 [<c0126fbc>] kthread+0x0/0xb7
 [<c0101329>] kernel_thread_helper+0x5/0xb
Code: 5c 24 08 8b 74 24 0c 89 44 24 1c 8b 7c 24 10 8b 6c 24 14 83 c4 18 e9 cd b1
fc ff 89 43 0c 89 48 04 31 db 89 51 04 89 4e 14 eb b7 <0f> 0b 27 01 3f ce 47 c0
eb 95 57
 <0>Kernel panic - not syncing: Fatal exception in interrupt




Put another way, I can setup, prep and create a software raid.. format it.. and
start to move data onto it.  I can even use it for quite some time.  However,
once the above happens once, I can not use that software raid again until I wipe
out the raid and start fresh.  Merely booting with the raid in causes the above
problem on bootup...