Bug 2975
| Summary: | Call trace when plugging in an external HD. | ||
|---|---|---|---|
| Product: | Drivers | Reporter: | Sebasti (annonygmouse) |
| Component: | USB | Assignee: | Greg Kroah-Hartman (greg) |
| Status: | REJECTED INSUFFICIENT_DATA | ||
| Severity: | normal | CC: | bunk |
| Priority: | P2 | ||
| Hardware: | i386 | ||
| OS: | Linux | ||
| Kernel Version: | debian 2.6.6-k7 | Subsystem: | |
| Regression: | --- | Bisected commit-id: | |
| Bug Depends on: | |||
| Bug Blocks: | 5089 | ||
Here is the tail -f /var/log/kern.log when plugging in after the boot process. This time I've left it going on for a while: Jun 29 00:45:59 maschine2 kernel: usb 4-4: new high speed USB device using address 2 Jun 29 00:46:00 maschine2 kernel: irq 21: nobody cared! Jun 29 00:46:00 maschine2 kernel: Call Trace: Jun 29 00:46:00 maschine2 kernel: [__report_bad_irq+42/144] __report_bad_irq+0x2a/0x90 Jun 29 00:46:00 maschine2 kernel: [note_interrupt+108/160] note_interrupt+0x6c/0xa0 Jun 29 00:46:00 maschine2 kernel: [do_IRQ+289/304] do_IRQ+0x121/0x130 Jun 29 00:46:00 maschine2 kernel: [common_interrupt+24/32] common_interrupt+0x18/0x20 Jun 29 00:46:00 maschine2 kernel: [default_idle+35/48] default_idle+0x23/0x30 Jun 29 00:46:00 maschine2 kernel: [cpu_idle+44/64] cpu_idle+0x2c/0x40 Jun 29 00:46:00 maschine2 kernel: [start_kernel+402/480] start_kernel+0x192/0x1e0 Jun 29 00:46:00 maschine2 kernel: [unknown_bootoption+0/352] unknown_bootoption+0x0/0x160 Jun 29 00:46:00 maschine2 kernel: Jun 29 00:46:00 maschine2 kernel: handlers: Jun 29 00:46:00 maschine2 kernel: [__crc_sleep_on+2540561/3958112] (usb_hcd_irq+0x0/0x70 [usbcore]) Jun 29 00:46:00 maschine2 last message repeated 2 times Jun 29 00:46:00 maschine2 kernel: Disabling IRQ #21 Jun 29 00:46:04 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:46:04 maschine2 kernel: ehci_hcd 0000:00:10.3: Unlink after no-IRQ? Different ACPI or APIC settings may help. Jun 29 00:46:09 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:46:09 maschine2 kernel: usb 4-4: device not accepting address 2, error -110 Jun 29 00:46:09 maschine2 kernel: ehci_hcd 0000:00:10.3: port 4 reset error -110 Jun 29 00:46:09 maschine2 kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 29 00:46:10 maschine2 kernel: ehci_hcd 0000:00:10.3: port 4 reset error -110 Jun 29 00:46:10 maschine2 kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 29 00:46:10 maschine2 kernel: ehci_hcd 0000:00:10.3: port 4 reset error -110 Jun 29 00:46:10 maschine2 kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 29 00:46:10 maschine2 kernel: usb 4-4: new high speed USB device using address 3 Jun 29 00:46:15 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:46:20 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:46:20 maschine2 kernel: usb 4-4: device not accepting address 3, error -110 Jun 29 00:46:21 maschine2 kernel: usb 4-4: new high speed USB device using address 4 Jun 29 00:46:26 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:46:31 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:46:31 maschine2 kernel: usb 4-4: device not accepting address 4, error -110 Jun 29 00:46:31 maschine2 kernel: usb 4-4: new high speed USB device using address 5 Jun 29 00:46:36 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:46:42 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:46:42 maschine2 kernel: usb 4-4: device not accepting address 5, error -110 Jun 29 00:46:42 maschine2 kernel: usb 4-4: new high speed USB device using address 6 Jun 29 00:46:47 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:46:52 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:46:52 maschine2 kernel: usb 4-4: device not accepting address 6, error -110 Jun 29 00:46:53 maschine2 kernel: usb 4-4: new high speed USB device using address 7 Jun 29 00:46:58 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:47:03 maschine2 kernel: usb 1-2: control timeout on ep0in Jun 29 00:47:03 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:47:03 maschine2 kernel: usb 4-4: device not accepting address 7, error -110 Jun 29 00:47:03 maschine2 kernel: ehci_hcd 0000:00:10.3: port 4 reset error -110 Jun 29 00:47:03 maschine2 kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 29 00:47:03 maschine2 kernel: ehci_hcd 0000:00:10.3: port 4 reset error -110 Jun 29 00:47:03 maschine2 kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 29 00:47:04 maschine2 kernel: usb 4-4: new high speed USB device using address 8 Jun 29 00:47:09 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:47:14 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:47:14 maschine2 kernel: usb 4-4: device not accepting address 8, error -110 Jun 29 00:47:14 maschine2 kernel: usb 4-4: new high speed USB device using address 9 Jun 29 00:47:19 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:47:24 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:47:25 maschine2 kernel: usb 4-4: device not accepting address 9, error -110 Jun 29 00:47:25 maschine2 kernel: usb 4-4: new high speed USB device using address 10 Jun 29 00:47:30 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:47:35 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:47:35 maschine2 kernel: usb 4-4: device not accepting address 10, error -110 Jun 29 00:47:36 maschine2 kernel: usb 4-4: new high speed USB device using address 11 Jun 29 00:47:41 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:47:46 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:47:46 maschine2 kernel: usb 4-4: device not accepting address 11, error -110 Jun 29 00:47:46 maschine2 kernel: usb 4-4: new high speed USB device using address 12 Jun 29 00:47:51 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:47:56 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:47:57 maschine2 kernel: usb 4-4: device not accepting address 12, error -110 Jun 29 00:47:57 maschine2 kernel: ehci_hcd 0000:00:10.3: port 4 reset error -110 Jun 29 00:47:57 maschine2 kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 29 00:47:57 maschine2 kernel: ehci_hcd 0000:00:10.3: port 4 reset error -110 Jun 29 00:47:57 maschine2 kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 29 00:47:57 maschine2 kernel: ehci_hcd 0000:00:10.3: port 4 reset error -110 Jun 29 00:47:57 maschine2 kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 29 00:47:57 maschine2 kernel: usb 4-4: new high speed USB device using address 13 Jun 29 00:48:02 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:48:08 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:48:08 maschine2 kernel: usb 4-4: device not accepting address 13, error -110 Jun 29 00:48:08 maschine2 kernel: usb 4-4: new high speed USB device using address 14 Jun 29 00:48:13 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:48:18 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:48:19 maschine2 kernel: usb 4-4: device not accepting address 14, error -110 Jun 29 00:48:19 maschine2 kernel: usb 4-4: new high speed USB device using address 15 Jun 29 00:48:24 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:48:29 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:48:29 maschine2 kernel: usb 4-4: device not accepting address 15, error -110 Jun 29 00:48:29 maschine2 kernel: usb 4-4: new high speed USB device using address 16 Jun 29 00:48:34 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:48:40 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:48:40 maschine2 kernel: usb 4-4: device not accepting address 16, error -110 Jun 29 00:48:40 maschine2 kernel: ehci_hcd 0000:00:10.3: port 4 reset error -110 Jun 29 00:48:40 maschine2 kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 29 00:48:40 maschine2 kernel: ehci_hcd 0000:00:10.3: port 4 reset error -110 Jun 29 00:48:40 maschine2 kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 29 00:48:40 maschine2 kernel: usb 4-4: new high speed USB device using address 17 Jun 29 00:48:45 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:48:51 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:48:51 maschine2 kernel: usb 4-4: device not accepting address 17, error -110 Jun 29 00:48:51 maschine2 kernel: usb 4-4: new high speed USB device using address 18 Jun 29 00:48:56 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:49:01 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:49:02 maschine2 kernel: usb 4-4: device not accepting address 18, error -110 Jun 29 00:49:02 maschine2 kernel: usb 4-4: new high speed USB device using address 19 Jun 29 00:49:07 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:49:12 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:49:12 maschine2 kernel: usb 4-4: device not accepting address 19, error -110 Jun 29 00:49:12 maschine2 kernel: usb 4-4: new high speed USB device using address 20 Jun 29 00:49:17 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:49:23 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:49:23 maschine2 kernel: usb 4-4: device not accepting address 20, error -110 Jun 29 00:49:23 maschine2 kernel: usb 4-4: new high speed USB device using address 21 Jun 29 00:49:28 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:49:33 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:49:34 maschine2 kernel: usb 4-4: device not accepting address 21, error -110 Jun 29 00:49:34 maschine2 kernel: usb 4-4: new high speed USB device using address 22 Jun 29 00:49:39 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:49:44 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:49:44 maschine2 kernel: usb 4-4: device not accepting address 22, error -110 Jun 29 00:49:44 maschine2 kernel: usb 4-4: new high speed USB device using address 23 Jun 29 00:49:49 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:49:55 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:49:55 maschine2 kernel: usb 4-4: device not accepting address 23, error -110 Jun 29 00:49:55 maschine2 kernel: ehci_hcd 0000:00:10.3: port 4 reset error -110 Jun 29 00:49:55 maschine2 kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 29 00:49:55 maschine2 kernel: ehci_hcd 0000:00:10.3: port 4 reset error -110 Jun 29 00:49:55 maschine2 kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 29 00:49:55 maschine2 kernel: usb 4-4: new high speed USB device using address 24 Jun 29 00:50:00 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:50:06 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:50:06 maschine2 kernel: usb 4-4: device not accepting address 24, error -110 Jun 29 00:50:06 maschine2 kernel: usb 4-4: new high speed USB device using address 25 Jun 29 00:50:11 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:50:16 maschine2 kernel: usb 4-4: control timeout on ep0out Jun 29 00:50:16 maschine2 kernel: usb 4-4: device not accepting address 25, error -110 Jun 29 00:50:17 maschine2 kernel: usb 4-4: new high speed USB device using address 26 Hope it helps... Is this issue still present in recent 2.6 kernels? Yes, please test a newer kernel, preferably 2.6.15 or newer. If the problem is still there, please reopen this bug with the new information. |
Distribution: Debian Hardware Environment: maschine2:/home/jo# sh /usr/src/kernel-kbuild-2.6-1/scripts/ver_linux If some fields are empty or look unusual you may have an old version. Compare to the current minimal requirements in Documentation/Changes. Linux maschine2 2.6.6-1-k7 #1 Wed May 12 18:19:40 EST 2004 i686 GNU/Linux Gnu C 3.3.4 Gnu make 3.80 binutils 2.14.90.0.7 util-linux 2.12 mount 2.12 module-init-tools 3.1-pre2 e2fsprogs 1.35 PPP 2.4.2 nfs-utils 1.0.6 Linux C Library 2.3.2 Dynamic linker (ldd) 2.3.2 Procps 3.2.1 Net-tools 1.60 Console-tools 0.2.3 Sh-utils 5.0.91 Modules Loaded rfcomm l2cap bluetooth parport_pc lp ipt_state ipt_MASQUERADE iptable_filter ip_nat_ftp iptable_nat ip_conntrack_irc ip_conntrack_ftp ip_conntrack ip_tables ipv6 snd_via82xx snd_ac97_codec gameport snd_mpu401_uart snd_rawmidi snd_seq_device via_ircc irda ehci_hcd sd_mod usblp uhci_hcd snd_bt87x snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd snd_page_alloc bt878 tuner tvaudio bttv video_buf i2c_algo_bit v4l2_common btcx_risc i2c_core videodev soundcore ne2k_pci 8390 8139too 8139cp mii crc32 pci_hotplug via_agp agpgart vfat fat tsdev mousedev evdev dm_mod capability commoncap xtkbd psmouse udf usb_storage usbcore scsi_mod ntfs nls_iso8859_1 nls_cp852 nls_cp437 nls_iso8859_15 parport af_packet rtc ext3 jbd mbcache ide_disk ide_generic via82cxxx ide_core unix font cfbcopyarea cfbimgblt cfbfillrect maschine2:/home/jo# cat /proc/interrupts CPU0 0: 1041074 IO-APIC-edge timer 1: 2189 IO-APIC-edge i8042 2: 0 XT-PIC cascade 7: 0 IO-APIC-edge parport0 8: 4 IO-APIC-edge rtc 12: 37595 IO-APIC-edge i8042 14: 16399 IO-APIC-edge ide0 15: 13 IO-APIC-edge ide1 16: 1160 IO-APIC-level bttv0, bt878 18: 5413 IO-APIC-level eth0 19: 0 IO-APIC-level ehci_hcd 21: 100000 IO-APIC-level uhci_hcd, uhci_hcd, uhci_hcd 22: 3086 IO-APIC-level VIA8233 NMI: 0 LOC: 1041110 ERR: 0 MIS: 0 maschine2:/home/jo# lspci 0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge 0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge 0000:00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 0000:00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS) 0000:00:0c.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11) 0000:00:0c.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11) 0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) 0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) 0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) 0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) 0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge 0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) 0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50) 0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY [Radeon 7000/VE] maschine2:/home/jo# maschine2:/home/jo# cat /proc/cpuinfo processor : 0 vendor_id : AuthenticAMD cpu family : 6 model : 8 model name : AMD Athlon(tm) XP 2200+ stepping : 1 cpu MHz : 1808.527 cache size : 256 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 1 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow bogomips : 3563.52 Software Environment: Debian Unstable Problem Description: Trying to put to work a ALUMINUM CONSTAR EXTERNAL BOX Model: ST-2512B2. It's a IDE to USB 2.0 adaptor. Two problems (probably same bug though): 1.- If already plugged in with a Hard Drive (Seagate Barracuda 120GB) shows the following during boot: Jun 28 19:16:26 maschine2 kernel: uhci_hcd 0000:00:10.1: VIA Technologies, Inc. USB (#2) Jun 28 19:16:26 maschine2 kernel: uhci_hcd 0000:00:10.1: irq 21, io base 0000dc00 Jun 28 19:16:26 maschine2 kernel: uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 Jun 28 19:16:26 maschine2 kernel: hub 2-0:1.0: USB hub found Jun 28 19:16:26 maschine2 kernel: hub 2-0:1.0: 2 ports detected Jun 28 19:16:26 maschine2 kernel: uhci_hcd 0000:00:10.2: VIA Technologies, Inc. USB (#3) Jun 28 19:16:26 maschine2 kernel: uhci_hcd 0000:00:10.2: irq 21, io base 0000e000 Jun 28 19:16:26 maschine2 kernel: uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 Jun 28 19:16:26 maschine2 kernel: usb 1-2: new full speed USB device using address 2 Jun 28 19:16:26 maschine2 kernel: hub 3-0:1.0: USB hub found Jun 28 19:16:26 maschine2 kernel: hub 3-0:1.0: 2 ports detected Jun 28 19:16:26 maschine2 kernel: drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x1204 Jun 28 19:16:26 maschine2 kernel: usbcore: registered new driver usblp Jun 28 19:16:26 maschine2 kernel: drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Jun 28 19:16:26 maschine2 kernel: usb 2-1: new full speed USB device using address 2 Jun 28 19:16:26 maschine2 kernel: scsi0 : SCSI emulation for USB Mass Storage devices Jun 28 19:16:26 maschine2 kernel: Vendor: ST312002 Model: 2A Rev: 0 0 Jun 28 19:16:26 maschine2 kernel: Type: Direct-Access ANSI SCSI revision: 02 Jun 28 19:16:26 maschine2 kernel: USB Mass Storage device found at 2 Jun 28 19:16:26 maschine2 kernel: SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB) Jun 28 19:16:26 maschine2 kernel: sda: assuming drive cache: write through Jun 28 19:16:26 maschine2 kernel: /dev/scsi/host0/bus0/target0/lun0: p1 Jun 28 19:16:26 maschine2 kernel: Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Jun 28 19:16:26 maschine2 kernel: ehci_hcd 0000:00:10.3: VIA Technologies, Inc. USB 2.0 Jun 28 19:16:26 maschine2 kernel: ehci_hcd 0000:00:10.3: irq 19, pci mem e0a20000 Jun 28 19:16:26 maschine2 kernel: ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 Jun 28 19:16:26 maschine2 kernel: ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29 Jun 28 19:16:26 maschine2 kernel: usb 1-2: USB disconnect, address 2 Jun 28 19:16:26 maschine2 kernel: drivers/usb/class/usblp.c: usblp0: removed Jun 28 19:16:26 maschine2 kernel: hub 4-0:1.0: USB hub found Jun 28 19:16:26 maschine2 kernel: hub 4-0:1.0: 6 ports detected Jun 28 19:16:26 maschine2 kernel: usb 2-1: USB disconnect, address 2 Jun 28 19:16:26 maschine2 kernel: usb 4-3: new high speed USB device using address 2 Jun 28 19:16:26 maschine2 kernel: irda_init() Jun 28 19:16:26 maschine2 kernel: NET: Registered protocol family 23 Jun 28 19:16:26 maschine2 kernel: irq 21: nobody cared! Jun 28 19:16:26 maschine2 kernel: Call Trace: Jun 28 19:16:26 maschine2 kernel: [__report_bad_irq+42/144] __report_bad_irq+0x2a/0x90 Jun 28 19:16:26 maschine2 kernel: [note_interrupt+108/160] note_interrupt+0x6c/0xa0 Jun 28 19:16:26 maschine2 kernel: [do_IRQ+289/304] do_IRQ+0x121/0x130 Jun 28 19:16:26 maschine2 kernel: [common_interrupt+24/32] common_interrupt+0x18/0x20 Jun 28 19:16:26 maschine2 kernel: Jun 28 19:16:26 maschine2 kernel: handlers: Jun 28 19:16:26 maschine2 kernel: [__crc_sleep_on+2540561/3958112] (usb_hcd_irq+0x0/0x70 [usbcore]) Jun 28 19:16:26 maschine2 last message repeated 2 times Jun 28 19:16:26 maschine2 kernel: Disabling IRQ #21 Jun 28 19:16:26 maschine2 kernel: PCI: Setting latency timer of device 0000:00:11.5 to 64 Jun 28 19:16:26 maschine2 kernel: eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 Jun 28 19:16:26 maschine2 kernel: usb 4-3: control timeout on ep0out Jun 28 19:16:26 maschine2 kernel: ehci_hcd 0000:00:10.3: Unlink after no-IRQ? Different ACPI or APIC settings may help. Jun 28 19:16:26 maschine2 kernel: NET: Registered protocol family 10 Jun 28 19:16:26 maschine2 kernel: Disabled Privacy Extensions on device c02e8f00(lo) Jun 28 19:16:26 maschine2 kernel: IPv6 over IPv4 tunneling driver Jun 28 19:16:26 maschine2 kernel: usb 4-3: control timeout on ep0out Jun 28 19:16:26 maschine2 kernel: usb 4-3: device not accepting address 2, error -110 Jun 28 19:16:26 maschine2 kernel: ip_tables: (C) 2000-2002 Netfilter core team Jun 28 19:16:27 maschine2 kernel: ip_conntrack version 2.1 (4095 buckets, 32760 max) - 296 bytes per conntrack Jun 28 19:16:27 maschine2 kernel: ehci_hcd 0000:00:10.3: port 3 reset error -110 Jun 28 19:16:27 maschine2 kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 28 19:16:27 maschine2 kernel: ehci_hcd 0000:00:10.3: port 3 reset error -110 Jun 28 19:16:27 maschine2 kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 28 19:16:27 maschine2 kernel: usb 4-3: new high speed USB device using address 3 Jun 28 19:16:28 maschine2 kernel: parport: PnPBIOS parport detected. Jun 28 19:16:28 maschine2 kernel: parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] Jun 28 19:16:28 maschine2 kernel: lp0: using parport0 (interrupt-driven). Jun 28 19:16:32 maschine2 kernel: usb 4-3: control timeout on ep0out Jun 28 19:16:34 maschine2 kernel: eth0: no IPv6 routers present Jun 28 19:16:37 maschine2 kernel: usb 4-3: control timeout on ep0out and keeps throwing: usb 4-3: control timeout on ep0out for a while. 2.- Plug ing after boot process finished: Jun 26 17:07:11 maschine2 kernel: usb 4-3: new high speed USB device using address 2 Jun 26 17:07:13 maschine2 kernel: Call Trace: Jun 26 17:07:13 maschine2 kernel: [__report_bad_irq+42/144] __report_bad_irq+0x2a/0x90 Jun 26 17:07:13 maschine2 kernel: [note_interrupt+108/160] note_interrupt+0x6c/0xa0 Jun 26 17:07:13 maschine2 kernel: [do_IRQ+289/304] do_IRQ+0x121/0x130 Jun 26 17:07:13 maschine2 kernel: [common_interrupt+24/32] common_interrupt+0x18/0x20 Jun 26 17:07:13 maschine2 kernel: [__crc___netdev_watchdog_up+2364544/2857393] Task_Switch+0x73f/0xaa0 [vmmon] Jun 26 17:07:13 maschine2 kernel: [__crc___netdev_watchdog_up+2355992/2857393] Vmx86_RunVM+0xd7/0x1e0 [vmmon] Jun 26 17:07:13 maschine2 kernel: [__crc___netdev_watchdog_up+2342102/2857393] LinuxDriver_Ioctl+0x1f5/0x8f0 [vmmon] Jun 26 17:07:13 maschine2 kernel: [ip_local_deliver_finish+0/464] ip_local_deliver_finish+0x0/0x1d0 Jun 26 17:07:13 maschine2 kernel: [ip_rcv_finish+513/672] ip_rcv_finish+0x201/0x2a0 Jun 26 17:07:13 maschine2 kernel: [ip_rcv_finish+0/672] ip_rcv_finish+0x0/0x2a0 Jun 26 17:07:13 maschine2 kernel: [nf_hook_slow+244/320] nf_hook_slow+0xf4/0x140 Jun 26 17:07:13 maschine2 kernel: [__crc_sleep_on+2540615/3958112] usb_hcd_irq+0x36/0x70 [usbcore] Jun 26 17:07:13 maschine2 kernel: [handle_IRQ_event+58/112] handle_IRQ_event+0x3a/0x70 Jun 26 17:07:13 maschine2 kernel: [__crc_sleep_on+2540615/3958112] usb_hcd_irq+0x36/0x70 [usbcore] Jun 26 17:07:13 maschine2 kernel: [handle_IRQ_event+58/112] handle_IRQ_event+0x3a/0x70 Jun 26 17:07:13 maschine2 kernel: [do_IRQ+180/304] do_IRQ+0xb4/0x130 Jun 26 17:07:13 maschine2 kernel: [common_interrupt+24/32] common_interrupt+0x18/0x20 Jun 26 17:07:13 maschine2 kernel: [schedule+842/1440] schedule+0x34a/0x5a0 Jun 26 17:07:13 maschine2 kernel: [__crc_sleep_on+2540615/3958112] usb_hcd_irq+0x36/0x70 [usbcore] Jun 26 17:07:13 maschine2 kernel: [sys_ioctl+269/656] sys_ioctl+0x10d/0x290 Jun 26 17:07:13 maschine2 kernel: [syscall_call+7/11] syscall_call+0x7/0xb Jun 26 17:07:13 maschine2 kernel: Jun 26 17:07:16 maschine2 kernel: usb 4-3: control timeout on ep0out Jun 26 17:07:16 maschine2 kernel: ehci_hcd 0000:00:10.3: Unlink after no-IRQ? Different ACPI or APIC settings may help. Jun 26 17:07:21 maschine2 kernel: usb 4-3: control timeout on ep0out Jun 26 17:07:22 maschine2 kernel: usb 4-3: new high speed USB device using address 3 Jun 26 17:07:27 maschine2 kernel: usb 4-3: control timeout on ep0out Jun 26 17:07:32 maschine2 kernel: usb 4-3: control timeout on ep0out Jun 26 17:07:32 maschine2 kernel: usb 4-3: new high speed USB device using address 4 Jun 26 17:07:37 maschine2 kernel: usb 4-3: control timeout on ep0out Jun 26 17:07:43 maschine2 kernel: usb 4-3: control timeout on ep0out Jun 26 17:07:43 maschine2 kernel: usb 4-3: new high speed USB device using address 5 Jun 26 17:07:48 maschine2 kernel: usb 4-3: control timeout on ep0out Jun 26 17:07:53 maschine2 kernel: usb 4-3: control timeout on ep0out Jun 26 17:08:04 maschine2 kernel: usb 4-3: new high speed USB device using address 6 Jun 26 17:08:09 maschine2 kernel: usb 4-3: control timeout on ep0out Jun 26 17:08:15 maschine2 kernel: usb 4-3: control timeout on ep0out Steps to reproduce: Problem 1: Boot with device already on. Problem 2: Start device after boot process. I have not seen anything in google about anyone having this thing... maybe the information of this device is not in the kernel yet??