Distribution: Debian SID Hardware Environment: Asus A7V-X 333, PS/2 Wheel mouse Software Environment: Problem Description: The mouse is detected on bootup, but no movement is send to the system. The device is avalaible, but a cat /dev/input/mice (and even /dev/input/mouse0 and /dev/psaux) will show nothing. Output of dmesg: Linux version 2.6.1 (root@master.hammer) (gcc-Version 3.3.3 20031229 (prerelease) (Debian)) #4 Fri Jan 9 21:51:52 CET 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fffc000 (usable) BIOS-e820: 000000001fffc000 - 000000001ffff000 (ACPI data) BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 511MB LOWMEM available. On node 0 totalpages: 131068 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126972 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 ASUS ) @ 0x000f5ea0 ACPI: RSDT (v001 ASUS A7V333-X 0x42302e31 MSFT 0x31313031) @ 0x1fffc000 ACPI: FADT (v001 ASUS A7V333-X 0x42302e31 MSFT 0x31313031) @ 0x1fffc0b2 ACPI: BOOT (v001 ASUS A7V333-X 0x42302e31 MSFT 0x31313031) @ 0x1fffc030 ACPI: MADT (v001 ASUS A7V333-X 0x42302e31 MSFT 0x31313031) @ 0x1fffc058 ACPI: DSDT (v001 ASUS A7V333-X 0x00001000 MSFT 0x0100000b) @ 0x00000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:8 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x1] trigger[0x1] lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0]) IOAPIC[0]: Assigned apic_id 2 IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, IRQ 0-23 ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x1]) ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x3] trigger[0x3]) Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Building zonelist for node : 0 Kernel command line: BOOT_IMAGE=2.6.0-ns ro root=2102 Initializing CPU#0 PID hash table entries: 2048 (order 11: 16384 bytes) Detected 1534.121 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Memory: 514624k/524272k available (2269k kernel code, 8852k reserved, 892k data, 268k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 3031.04 BogoMIPS Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: AMD Athlon(TM) XP 1800+ stepping 00 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 ENABLING IO-APIC IRQs init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=-1 number of MP IRQ sources: 15. number of IO-APIC #2 registers: 24. testing the IO APIC....................... IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178003 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0003 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 001 01 0 0 0 0 0 1 1 51 06 001 01 0 0 0 0 0 1 1 59 07 001 01 0 0 0 0 0 1 1 61 08 001 01 0 0 0 0 0 1 1 69 09 001 01 1 1 0 1 0 1 1 71 0a 001 01 0 0 0 0 0 1 1 79 0b 001 01 0 0 0 0 0 1 1 81 0c 001 01 0 0 0 0 0 1 1 89 0d 001 01 0 0 0 0 0 1 1 91 0e 001 01 0 0 0 0 0 1 1 99 0f 001 01 0 0 0 0 0 1 1 A1 10 000 00 1 0 0 0 0 0 0 00 11 000 00 1 0 0 0 0 0 0 00 12 000 00 1 0 0 0 0 0 0 00 13 000 00 1 0 0 0 0 0 0 00 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 1533.0191 MHz. ..... host bus clock speed is 266.0641 MHz. NET: Registered protocol family 16 EISA bus registered PCI: PCI BIOS revision 2.10 entry at 0xf1640, last bus=1 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20031002 IOAPIC[0]: Set PCI routing entry (2-9 -> 0x71 -> IRQ 9 Mode:1 Active:1) ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00f9cd0 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x9d00, dseg 0xf0000 pnp: 00:12: ioport range 0xe400-0xe47f has been reserved PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver SCSI subsystem initialized IOAPIC[0]: Set PCI routing entry (2-18 -> 0xa9 -> IRQ 18 Mode:1 Active:1) 00:00:09[A] -> 2-18 -> IRQ 18 IOAPIC[0]: Set PCI routing entry (2-19 -> 0xb1 -> IRQ 19 Mode:1 Active:1) 00:00:0c[A] -> 2-19 -> IRQ 19 IOAPIC[0]: Set PCI routing entry (2-16 -> 0xb9 -> IRQ 16 Mode:1 Active:1) 00:00:0c[B] -> 2-16 -> IRQ 16 IOAPIC[0]: Set PCI routing entry (2-17 -> 0xc1 -> IRQ 17 Mode:1 Active:1) 00:00:0c[C] -> 2-17 -> IRQ 17 Pin 2-18 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed IOAPIC[0]: Set PCI routing entry (2-21 -> 0xc9 -> IRQ 21 Mode:1 Active:1) 00:00:10[A] -> 2-21 -> IRQ 21 Pin 2-21 already programmed Pin 2-21 already programmed Pin 2-21 already programmed IOAPIC[0]: Set PCI routing entry (2-22 -> 0xd1 -> IRQ 22 Mode:1 Active:1) 00:00:11[C] -> 2-22 -> IRQ 22 Pin 2-16 already programmed Pin 2-17 already programmed ACPI: No IRQ known for interrupt pin A of device 0000:00:11.1 - using IRQ 255 PCI: Using ACPI for IRQ routing PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' SBF: Simple Boot Flag extension found and enabled. SBF: Setting boot flags 0x1 VFS: Disk quotas dquot_6.5.1 udf: registering filesystem Initializing Cryptographic API PCI: Via IRQ fixup for 0000:00:10.0, from 9 to 5 PCI: Via IRQ fixup for 0000:00:10.1, from 9 to 5 PCI: Via IRQ fixup for 0000:00:10.2, from 9 to 5 pty: 256 Unix98 ptys configured request_module: failed /sbin/modprobe -- parport_lowlevel. error = -16 lp: driver loaded but no devices found Using anticipatory io scheduler Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx SiI680: IDE controller at PCI slot 0000:00:0f.0 SiI680: chipset revision 1 SiI680: BASE CLOCK == 100 SiI680: 100% native mode on irq 18 ide0: BM-DMA at 0xa800-0xa807, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xa808-0xa80f, BIOS settings: hdc:pio, hdd:pio hda: LITEON DVD-ROM LTD122, ATAPI CD/DVD-ROM drive ide0 at 0xd000-0xd007,0xb802 on irq 18 hdd: CREATIVE CD-RW RW8438E, ATAPI CD/DVD-ROM drive ide1 at 0xb400-0xb407,0xb002 on irq 18 VP_IDE: IDE controller at PCI slot 0000:00:11.1 ACPI: No IRQ known for interrupt pin A of device 0000:00:11.1 - using IRQ 255 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1 ide2: BM-DMA at 0x9400-0x9407, BIOS settings: hde:DMA, hdf:pio ide3: BM-DMA at 0x9408-0x940f, BIOS settings: hdg:DMA, hdh:pio hde: Maxtor 6Y060L0, ATA DISK drive ide2 at 0x1f0-0x1f7,0x3f6 on irq 14 hdg: HL-DT-ST DVDRAM GSA-4040B, ATAPI CD/DVD-ROM drive ide3 at 0x170-0x177,0x376 on irq 15 hde: max request size: 128KiB hde: 120103200 sectors (61492 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133) hde: hde1 hde2 hde3 < hde5 > hde4 hda: ATAPI 40X DVD-ROM drive, 512kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 hdd: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA hdg: ATAPI 32X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) mice: PS/2 mouse device common for all mice input: Analog 3-axis 4-button joystick at pci0000:00:0e.1/gameport0 [TSC timer, 1515 MHz clock, 840 ns res] gameport: pci0000:00:0e.1 speed 1242 kHz serio: i8042 AUX port at 0x60,0x64 irq 12 input: ImPS/2 Generic Wheel Mouse on isa0060/serio1 serio: i8042 KBD port at 0x60,0x64 irq 1 input: AT Translated Set 2 keyboard on isa0060/serio0 I2O Core - (C) Copyright 1999 Red Hat Software I2O: Event thread created as pid 11 i2o: Checking for PCI I2O controllers... I2O configuration manager v 0.04. (C) Copyright 1999 Red Hat Software i2c /dev entries driver EISA: Probing bus 0 at eisa0 Advanced Linux Sound Architecture Driver Version 0.9.7 (Thu Sep 25 19:16:36 2003 UTC). ALSA device list: No soundcards found. NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) NET: Registered protocol family 1 NET: Registered protocol family 8 NET: Registered protocol family 20 ACPI: (supports S0 S1 S4 S5) kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 268k freed Adding 995988k swap on /dev/hde5. Priority:-1 extents:1 EXT3 FS on hde2, internal journal Real Time Clock Driver v1.12 Linux video capture interface: v1.00 bttv: driver version 0.9.12 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). bttv0: Bt878 (rev 17) at 0000:00:0a.0, irq: 16, latency: 32, mmio: 0xed000000 bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb bttv0: using: Hauppauge (bt878) [card=10,autodetected] bttv0: Hauppauge/Voodoo msp34xx: reset line init [5] bttv0: Hauppauge eeprom: model=44354, tuner=Philips FM1216 (5), radio=yes bttv0: using tuner=5 bttv0: i2c: checking for MSP34xx @ 0x80... found msp34xx: init: chip=MSP3415D-B3 +nicam +simple msp3410: daemon started registering 0-0040 bttv0: i2c: checking for TDA9875 @ 0xb0... not found bttv0: i2c: checking for TDA7432 @ 0x8a... not found tvaudio: TV audio decoder + audio/video mux driver tvaudio: known chips: tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54 (PV951),ta8874z tuner: chip found @ 0xc2 tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) registering 0-0061 bttv0: registered device video0 bttv0: registered device vbi0 bttv0: registered device radio0 bttv0: PLL: 28636363 => 35468950 .. ok Linux agpgart interface v0.100 (c) Dave Jones [drm:drm_init] *ERROR* Cannot initialize the agpgart module. registering 1-002d registering 1-0049 registering 1-0048 tuner: type already set (5) registering 0-0050 tuner: type already set (5) registering 0-0051 tuner: type already set (5) registering 0-0052 tuner: type already set (5) registering 0-0053 tuner: type already set (5) registering 0-0054 tuner: type already set (5) registering 0-0055 tuner: type already set (5) registering 0-0056 tuner: type already set (5) registering 0-0057 CSLIP: code copyright 1989 Regents of the University of California PPP generic driver version 2.4.2 blk: queue dfda4600, I/O limit 4095Mb (mask 0xffffffff) hda: CHECK for good STATUS hdd: CHECK for good STATUS hdg: CHECK for good STATUS request_module: failed /sbin/modprobe -- char-major-4-64. error = 256 Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A found reiserfs format "3.6" with standard journal Reiserfs journal params: device hde4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (hde4) for (hde4) Using r5 hash to sort names request_module: failed /sbin/modprobe -- eth0. error = 256 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 4 sensors: numerical sysctl 7 2 1 is obsolete. sensord: numerical sysctl 7 2 1 is obsolete. nfs warning: mount version older than kernel request_module: failed /sbin/modprobe -- char-major-188-0. error = 256 drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hub request_module: failed /sbin/modprobe -- char-major-10-134. error = 256 request_module: failed /sbin/modprobe -- char-major-226-0. error = 256 [drm:drm_init] *ERROR* Cannot initialize the agpgart module. atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0). atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0). Output of "cat /dev/interrupts": CPU0 0: 556870 IO-APIC-edge timer 1: 3530 IO-APIC-edge i8042 2: 0 XT-PIC cascade 8: 4 IO-APIC-edge rtc 9: 0 IO-APIC-level acpi 12: 62 IO-APIC-edge i8042 14: 11913 IO-APIC-edge ide2 15: 25 IO-APIC-edge ide3 16: 4 IO-APIC-level bttv0 18: 46 IO-APIC-level ide0, ide1 NMI: 0 LOC: 556789 ERR: 0 MIS: 0 Part of .config: # # Input device support # CONFIG_INPUT=y # # Userland interfaces # CONFIG_INPUT_MOUSEDEV=y CONFIG_INPUT_MOUSEDEV_PSAUX=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 CONFIG_INPUT_JOYDEV=y # CONFIG_INPUT_TSDEV is not set CONFIG_INPUT_EVDEV=m # CONFIG_INPUT_EVBUG is not set # # Input I/O drivers # CONFIG_GAMEPORT=y CONFIG_SOUND_GAMEPORT=y # CONFIG_GAMEPORT_NS558 is not set # CONFIG_GAMEPORT_L4 is not set CONFIG_GAMEPORT_EMU10K1=y # CONFIG_GAMEPORT_VORTEX is not set # CONFIG_GAMEPORT_FM801 is not set # CONFIG_GAMEPORT_CS461x is not set CONFIG_SERIO=y CONFIG_SERIO_I8042=y # CONFIG_SERIO_SERPORT is not set # CONFIG_SERIO_CT82C710 is not set # CONFIG_SERIO_PARKBD is not set # CONFIG_SERIO_PCIPS2 is not set # # Input Device Drivers # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y # CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_XTKBD is not set # CONFIG_KEYBOARD_NEWTON is not set CONFIG_INPUT_MOUSE=y CONFIG_MOUSE_PS2=y # CONFIG_MOUSE_SERIAL is not set # CONFIG_MOUSE_INPORT is not set # CONFIG_MOUSE_LOGIBM is not set # CONFIG_MOUSE_PC110PAD is not set CONFIG_INPUT_JOYSTICK=y CONFIG_JOYSTICK_ANALOG=y CONFIG_JOYSTICK_A3D=m CONFIG_JOYSTICK_ADI=m CONFIG_JOYSTICK_COBRA=m CONFIG_JOYSTICK_GF2K=m CONFIG_JOYSTICK_GRIP=m CONFIG_JOYSTICK_GRIP_MP=m CONFIG_JOYSTICK_GUILLEMOT=m CONFIG_JOYSTICK_INTERACT=m CONFIG_JOYSTICK_SIDEWINDER=m CONFIG_JOYSTICK_TMDC=m CONFIG_JOYSTICK_IFORCE=m CONFIG_JOYSTICK_IFORCE_USB=y CONFIG_JOYSTICK_IFORCE_232=y CONFIG_JOYSTICK_WARRIOR=m CONFIG_JOYSTICK_MAGELLAN=m CONFIG_JOYSTICK_SPACEORB=m CONFIG_JOYSTICK_SPACEBALL=m CONFIG_JOYSTICK_STINGER=m CONFIG_JOYSTICK_TWIDDLER=m CONFIG_JOYSTICK_DB9=m CONFIG_JOYSTICK_GAMECON=m CONFIG_JOYSTICK_TURBOGRAFX=m CONFIG_INPUT_JOYDUMP=m # CONFIG_INPUT_TOUCHSCREEN is not set CONFIG_INPUT_MISC=y # CONFIG_INPUT_PCSPKR is not set CONFIG_INPUT_UINPUT=m Output of "lspci -v": 00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400 AGP] Host Bridge Subsystem: Asustek Computer, Inc. A7V8X motherboard Flags: bus master, 66Mhz, medium devsel, latency 0 Memory at f0000000 (32-bit, prefetchable) [size=128M] Capabilities: [a0] AGP version 2.0 Capabilities: [c0] Power Management version 2 00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge (prog-if 00 [Normal decode]) Flags: bus master, 66Mhz, medium devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: eb000000-ec6fffff Prefetchable memory behind bridge: edf00000-efffffff Capabilities: [80] Power Management version 2 00:09.0 Ethernet controller: Broadcom Corporation BCM4401 100Base-T (rev 01) Subsystem: Asustek Computer, Inc. A7V8X motherboard Flags: bus master, fast devsel, latency 32, IRQ 9 Memory at ea800000 (32-bit, non-prefetchable) [size=8K] Expansion ROM at edef0000 [disabled] [size=16K] Capabilities: [40] Power Management version 2 00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11) Subsystem: Hauppauge computer works Inc. WinTV Series Flags: bus master, medium devsel, latency 32, IRQ 11 Memory at ed000000 (32-bit, prefetchable) [size=4K] Capabilities: [44] Vital Product Data Capabilities: [4c] Power Management version 2 00:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11) Subsystem: Hauppauge computer works Inc. WinTV Series Flags: bus master, medium devsel, latency 32, IRQ 11 Memory at ec800000 (32-bit, prefetchable) [size=4K] Capabilities: [44] Vital Product Data Capabilities: [4c] Power Management version 2 00:0e.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 06) Subsystem: Creative Labs CT4832 SBLive! Value Flags: bus master, medium devsel, latency 32, IRQ 10 I/O ports at d800 [size=32] Capabilities: [dc] Power Management version 1 00:0e.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 06) Subsystem: Creative Labs Gameport Joystick Flags: bus master, medium devsel, latency 32 I/O ports at d400 [size=8] Capabilities: [dc] Power Management version 1 00:0f.0 RAID bus controller: CMD Technology Inc PCI0680 (rev 01) Subsystem: CMD Technology Inc PCI0680 Flags: bus master, medium devsel, latency 32, IRQ 9 I/O ports at d000 [size=8] I/O ports at b800 [size=4] I/O ports at b400 [size=8] I/O ports at b000 [size=4] I/O ports at a800 [size=16] Expansion ROM at <unassigned> [disabled] [size=512K] Capabilities: [60] Power Management version 2 00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI]) Subsystem: Asustek Computer, Inc. A7V8X motherboard Flags: bus master, medium devsel, latency 32, IRQ 9 I/O ports at a400 [size=32] Capabilities: [80] Power Management version 2 00:10.1 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI]) Subsystem: Asustek Computer, Inc. A7V8X motherboard Flags: bus master, medium devsel, latency 32, IRQ 9 I/O ports at a000 [size=32] Capabilities: [80] Power Management version 2 00:10.2 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI]) Subsystem: Asustek Computer, Inc. A7V8X motherboard Flags: bus master, medium devsel, latency 32, IRQ 9 I/O ports at 9800 [size=32] Capabilities: [80] Power Management version 2 00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI]) Subsystem: Asustek Computer, Inc. A7V8X motherboard Flags: bus master, medium devsel, latency 32, IRQ 9 Memory at ea000000 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge Subsystem: Asustek Computer, Inc. A7V8X motherboard Flags: bus master, stepping, medium devsel, latency 0 Capabilities: [c0] Power Management version 2 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: Asustek Computer, Inc. A7V8X motherboard Flags: bus master, medium devsel, latency 32 I/O ports at 9400 [size=16] Capabilities: [c0] Power Management version 2 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235 AC97 Audio Controller (rev 50) Subsystem: Asustek Computer, Inc. A7V8X Motherboard (Realtek ALC650 codec) Flags: medium devsel, IRQ 9 I/O ports at e000 [size=256] Capabilities: [c0] Power Management version 2 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G550 AGP (rev 01) (prog-if 00 [VGA]) Subsystem: Matrox Graphics, Inc. Millennium G550 Dual Head DDR 32Mb Flags: bus master, medium devsel, latency 64, IRQ 11 Memory at ee000000 (32-bit, prefetchable) [size=32M] Memory at eb800000 (32-bit, non-prefetchable) [size=16K] Memory at eb000000 (32-bit, non-prefetchable) [size=8M] Expansion ROM at edfe0000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2 Capabilities: [f0] AGP version 2.0
I'd suggest disabling APIC for a test, by passing 'noapic' to the kernel command line. Then checking /proc/interrupts to see whether the count for IRQ12 is increasing would be a good idea, too. And last, when everything fails, enable DEBUG in i8042.h.
Created attachment 2002 [details] the output of dmesg, /dev/interrupts, lsmod and the .config from kernel-compiling
same problem even with kernel-2.6.2-rc2-mm1 and asus a7v (no x-333). the pointer is a "logitech pilot wheel mouse" on ps/2. i've got no response on cat /dev/psaux, /dev/input/mouse0 or /dev/input/mice - absolute nothing. mdetect shows an intellimouse on psaux. i tried compiling psmouse etc. as module and static - nothing changed. - oh, and i don't use acpi. so any suggestions? i inlcuded the output of dmesg, /proc/interrupts, lsmod and my .config. mfg Florian Miess
Created attachment 2061 [details] ASUS A7V-133-C seems to have the same problem I tested kernel 2.6.1 and 2.6.2 on my Gentoo with Asus A7V-133-C and had the same problem. Nothing happenned when I "cat /dev/psaux" and /proc/interrupts IRQ 12 had no increase. APIC and ACPI did not affect the result. Dmesg showed the same messages in the mouse part as the original report did.
Sorry for my wrong report. The problem was caused by KVM switch.The ps/2 mouse works fine on my A7V-133-C now without KVM switch.
Florian, Do you still have problem with your mouse using recent kernels (2.6.19/2.6.20)? Thanks!
I'm sorry, can't answer this: meanwhile i've got an usb mouse...