Distribution: Hardware Environment: HP Compaq 6715s notebook Software Environment: 32 bit system Problem Description: Hello, I get every few minutes following error messages in my kernel log: bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed. bcm43xx: core_up for active 802.11 core failed (-2) bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed. bcm43xx: core_up for active 802.11 core failed (-2) bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed. bcm43xx: core_up for active 802.11 core failed (-2) bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed. bcm43xx: core_up for active 802.11 core failed (-2) bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed. bcm43xx: core_up for active 802.11 core failed (-2) bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed. bcm43xx: core_up for active 802.11 core failed (-2) bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed. bcm43xx: core_up for active 802.11 core failed (-2) bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed. bcm43xx: core_up for active 802.11 core failed (-2) bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed. bcm43xx: core_up for active 802.11 core failed (-2) bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed. bcm43xx: core_up for active 802.11 core failed (-2) Currently I'm not using wireless eth, so it's just loaded and inactive. Output of lspci -vv: 30:00.0 Network controller: Broadcom Corporation BCM4310 UART (rev 02) Subsystem: Hewlett-Packard Company Unknown device 1371 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 20 Region 0: Memory at c8000000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME- Capabilities: [58] Vendor Specific Information Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [d0] Express Endpoint IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+ Device: Latency L0s <4us, L1 unlimited Device: AtnBtn- AtnInd- PwrInd- Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0 Link: Latency L0s <4us, L1 <64us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x1 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel Capabilities: [160] Device Serial Number 1a-00-6f-ff-ff-73-8e-57 Capabilities: [16c] Power Budgeting Cheers.
I'm sorry, my firmware was missing.