Reply-To: akpm@linux-foundation.org

On Fri, 8 Jun 2007 21:29:13 -0700 bugme-daemon@bugzilla.kernel.org wrote:

> http://bugzilla.kernel.org/show_bug.cgi?id=8602
> 
>            Summary: Computer becomes work too slowly when usb drive
>                     connected and after that
>     Kernel Version: 2.6.19.2
>             Status: NEW
>           Severity: normal
>              Owner: other_other@kernel-bugs.osdl.org
>          Submitter: s.levashev@telvis.ru
> 
> 
> I have old computer :) and bought VIA PCI USB controller. Mouse and 
> printer/scanner works fine, but when i connect a usb drive or card reader, 
> system becomes work very slowly. Deattach of usb drive/reader does not take 
> effect. Disabling udev,dbus and hal services does not take effect too :(
> 
> 
> Linux chek 2.6.19.2 #19 Wed May 23 19:42:29 NOVST 2007 i586 AMD-K6(tm) 3D 
> processor AuthenticAMD GNU/Linux
> 
> Gnu C                  3.4.6
> Gnu make               3.81
> binutils               2.17
> util-linux             2.12r
> mount                  2.12r
> module-init-tools      3.2.2
> e2fsprogs              1.39
> PPP                    2.4.4
> Linux C Library        > libc.2.5
> Dynamic linker (ldd)   2.5
> Procps                 3.2.7
> Net-tools              1.60
> Kbd                    1.12
> Sh-utils               6.7
> udev                   103
> Modules Loaded         nvidia
> 
> lspci -vvv:
> =================================================================
> 00:00.0 Host bridge: ALi Corporation M1541 (rev 04)
> 	Subsystem: ALi Corporation ALI M1541 Aladdin V/V+ AGP System Controller
> 	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- 
> SERR- FastB2B-
> 	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- 
> <MAbort+ >SERR- <PERR-
> 	Latency: 32
> 	Region 0: Memory at d8000000 (32-bit, non-prefetchable) [size=64M]
> 	Capabilities: [b0] AGP version 1.0
> 		Status: RQ=28 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 
> 64bit- FW- 
> AGP3- Rate=x1,x2
> 		Command: RQ=28 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- 
> Rate=x1
> 
> 00:01.0 PCI bridge: ALi Corporation M1541 PCI to AGP Controller (rev 04) 
> (prog-if 00 [Normal decode])
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- 
> SERR+ FastB2B-
> 	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- 
> <MAbort- >SERR- <PERR-
> 	Latency: 32
> 	Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
> 	I/O behind bridge: 0000f000-00000fff
> 	Memory behind bridge: dc000000-ddffffff
> 	Prefetchable memory behind bridge: de000000-dfffffff
> 	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
> <MAbort+ <SERR- <PERR-
> 	BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
> 
> 00:07.0 ISA bridge: ALi Corporation M1533/M1535 PCI to ISA Bridge [Aladdin 
> IV/V/V+] (rev c3)
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- 
> Stepping- 
> SERR- FastB2B-
> 	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
> <TAbort+ 
> <MAbort+ >SERR- <PERR-
> 	Latency: 0
> 
> 00:0d.0 IDE interface: ALi Corporation M5229 IDE (rev c1) (prog-if fa)
> 	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- 
> SERR- FastB2B-
> 	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
> <TAbort- 
> <MAbort- >SERR- <PERR-
> 	Latency: 32 (500ns min, 1000ns max)
> 	Interrupt: pin A routed to IRQ 9
> 	Region 4: I/O ports at f000 [size=16]
> 
> 00:0e.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture 
> (rev 11)
> 	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- 
> SERR- FastB2B-
> 	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
> <TAbort- 
> <MAbort- >SERR- <PERR-
> 	Latency: 32 (4000ns min, 10000ns max)
> 	Interrupt: pin A routed to IRQ 10
> 	Region 0: Memory at e0001000 (32-bit, prefetchable) [size=4K]
> 	Capabilities: [44] Vital Product Data
> 	Capabilities: [4c] Power Management version 2
> 		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA 
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> 		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 
> 00:0e.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 
> 11)
> 	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- 
> SERR- FastB2B-
> 	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
> <TAbort- 
> <MAbort- >SERR- <PERR-
> 	Latency: 32 (1000ns min, 63750ns max)
> 	Interrupt: pin A routed to IRQ 10
> 	Region 0: Memory at e0002000 (32-bit, prefetchable) [size=4K]
> 	Capabilities: [44] Vital Product Data
> 	Capabilities: [4c] Power Management version 2
> 		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA 
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> 		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 
> 00:0f.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 
> Controller (rev 61) (prog-if 00 [UHCI])
> 	Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- 
> SERR- FastB2B-
> 	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
> <TAbort- 
> <MAbort- >SERR- <PERR-
> 	Latency: 32, Cache Line Size: 32 bytes
> 	Interrupt: pin A routed to IRQ 12
> 	Region 4: I/O ports at d000 [size=32]
> 	Capabilities: [80] Power Management version 2
> 		Flags: PMEClk+ DSI- D1+ D2+ AuxCurrent=0mA 
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> 		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 
> 00:0f.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 
> Controller (rev 61) (prog-if 00 [UHCI])
> 	Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- 
> SERR- FastB2B-
> 	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
> <TAbort- 
> <MAbort- >SERR- <PERR-
> 	Latency: 32, Cache Line Size: 32 bytes
> 	Interrupt: pin B routed to IRQ 5
> 	Region 4: I/O ports at d400 [size=32]
> 	Capabilities: [80] Power Management version 2
> 		Flags: PMEClk+ DSI- D1+ D2+ AuxCurrent=0mA 
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> 		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 
> 00:0f.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 63) (prog-if 20 
> [EHCI])
> 	Subsystem: VIA Technologies, Inc. USB 2.0
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
> Stepping- 
> SERR- FastB2B-
> 	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
> <TAbort- 
> <MAbort- >SERR- <PERR-
> 	Latency: 32, Cache Line Size: 32 bytes
> 	Interrupt: pin C routed to IRQ 11
> 	Region 0: Memory at e0003000 (32-bit, non-prefetchable) [size=256]
> 	Capabilities: [80] Power Management version 2
> 		Flags: PMEClk+ DSI- D1+ D2+ AuxCurrent=0mA 
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
> 		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 
> 00:10.0 Multimedia audio controller: ESS Technology ES1969 Solo-1 Audiodrive 
> (rev 01)
> 	Subsystem: ESS Technology Solo-1 Audio Adapter
> 	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- 
> SERR- FastB2B-
> 	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
> <TAbort- 
> <MAbort- >SERR- <PERR-
> 	Latency: 32 (500ns min, 6000ns max)
> 	Interrupt: pin A routed to IRQ 5
> 	Region 0: I/O ports at d800 [size=64]
> 	Region 1: I/O ports at dc00 [size=16]
> 	Region 2: I/O ports at e000 [size=16]
> 	Region 3: I/O ports at e400 [size=4]
> 	Region 4: I/O ports at e800 [size=4]
> 	Capabilities: [c0] Power Management version 1
> 		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA 
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> 		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 
> 01:00.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 
> 64/Model 64 Pro] (rev 15) (prog-if 00 [VGA])
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
> Stepping- 
> SERR- FastB2B-
> 	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
> <TAbort- 
> <MAbort- >SERR- <PERR-
> 	Latency: 248 (1250ns min, 250ns max)
> 	Interrupt: pin A routed to IRQ 11
> 	Region 0: Memory at dc000000 (32-bit, non-prefetchable) [size=16M]
> 	Region 1: Memory at de000000 (32-bit, prefetchable) [size=32M]
> 	[virtual] Expansion ROM at dd000000 [disabled] [size=64K]
> 	Capabilities: [60] Power Management version 1
> 		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> 		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 	Capabilities: [44] AGP version 2.0
> 		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 
> 64bit- FW- 
> AGP3- Rate=x1,x2,x4
> 		Command: RQ=28 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- 
> Rate=x1
> 
> =================================================================
> 
> lsusb -vvv:
> =================================================================
> 
> Bus 003 Device 001: ID 0000:0000  
> Device Descriptor:
>   bLength                18
>   bDescriptorType         1
>   bcdUSB               1.10
>   bDeviceClass            9 Hub
>   bDeviceSubClass         0 Unused
>   bDeviceProtocol         0 
>   bMaxPacketSize0        64
>   idVendor           0x0000 
>   idProduct          0x0000 
>   bcdDevice            2.06
>   iManufacturer           3 Linux 2.6.19.2 uhci_hcd
>   iProduct                2 UHCI Host Controller
>   iSerial                 1 0000:00:0f.1
>   bNumConfigurations      1
>   Configuration Descriptor:
>     bLength                 9
>     bDescriptorType         2
>     wTotalLength           25
>     bNumInterfaces          1
>     bConfigurationValue     1
>     iConfiguration          0 
>     bmAttributes         0xe0
>       Self Powered
>       Remote Wakeup
>     MaxPower                0mA
>     Interface Descriptor:
>       bLength                 9
>       bDescriptorType         4
>       bInterfaceNumber        0
>       bAlternateSetting       0
>       bNumEndpoints           1
>       bInterfaceClass         9 Hub
>       bInterfaceSubClass      0 Unused
>       bInterfaceProtocol      0 
>       iInterface              0 
>       Endpoint Descriptor:
>         bLength                 7
>         bDescriptorType         5
>         bEndpointAddress     0x81  EP 1 IN
>         bmAttributes            3
>           Transfer Type            Interrupt
>           Synch Type               None
>           Usage Type               Data
>         wMaxPacketSize     0x0002  1x 2 bytes
>         bInterval             255
> Hub Descriptor:
>   bLength               9
>   bDescriptorType      41
>   nNbrPorts             2
>   wHubCharacteristic 0x000a
>     No power switching (usb 1.0)
>     Per-port overcurrent protection
>   bPwrOn2PwrGood        1 * 2 milli seconds
>   bHubContrCurrent      0 milli Ampere
>   DeviceRemovable    0x00
>   PortPwrCtrlMask    0x00 
>  Hub Port Status:
>    Port 1: 0000.0100 power
>    Port 2: 0000.0100 power
> 
> Bus 002 Device 003: ID 046d:c00e Logitech, Inc. Optical Mouse
> Device Descriptor:
>   bLength                18
>   bDescriptorType         1
>   bcdUSB               2.00
>   bDeviceClass            0 (Defined at Interface level)
>   bDeviceSubClass         0 
>   bDeviceProtocol         0 
>   bMaxPacketSize0         8
>   idVendor           0x046d Logitech, Inc.
>   idProduct          0xc00e Optical Mouse
>   bcdDevice           11.10
>   iManufacturer           1 Logitech
>   iProduct                2 USB-PS/2 Optical Mouse
>   iSerial                 0 
>   bNumConfigurations      1
>   Configuration Descriptor:
>     bLength                 9
>     bDescriptorType         2
>     wTotalLength           34
>     bNumInterfaces          1
>     bConfigurationValue     1
>     iConfiguration          0 
>     bmAttributes         0xa0
>       Remote Wakeup
>     MaxPower               98mA
>     Interface Descriptor:
>       bLength                 9
>       bDescriptorType         4
>       bInterfaceNumber        0
>       bAlternateSetting       0
>       bNumEndpoints           1
>       bInterfaceClass         3 Human Interface Devices
>       bInterfaceSubClass      1 Boot Interface Subclass
>       bInterfaceProtocol      2 Mouse
>       iInterface              0 
>         HID Device Descriptor:
>           bLength                 9
>           bDescriptorType        33
>           bcdHID               1.10
>           bCountryCode            0 Not supported
>           bNumDescriptors         1
>           bDescriptorType        34 Report
>           wDescriptorLength      52
>          Report Descriptors: 
>            ** UNAVAILABLE **
>       Endpoint Descriptor:
>         bLength                 7
>         bDescriptorType         5
>         bEndpointAddress     0x81  EP 1 IN
>         bmAttributes            3
>           Transfer Type            Interrupt
>           Synch Type               None
>           Usage Type               Data
>         wMaxPacketSize     0x0004  1x 4 bytes
>         bInterval              10
> 
> Bus 002 Device 002: ID 0924:423b Xerox 
> Device Descriptor:
>   bLength                18
>   bDescriptorType         1
>   bcdUSB               1.10
>   bDeviceClass            0 (Defined at Interface level)
>   bDeviceSubClass         0 
>   bDeviceProtocol         0 
>   bMaxPacketSize0         8
>   idVendor           0x0924 Xerox
>   idProduct          0x423b 
>   bcdDevice            1.00
>   iManufacturer           1 Xerox
>   iProduct                2 Xerox WorkCentre PE114 Series
>   iSerial                 3 3561806259......
>   bNumConfigurations      1
>   Configuration Descriptor:
>     bLength                 9
>     bDescriptorType         2
>     wTotalLength           32
>     bNumInterfaces          1
>     bConfigurationValue     1
>     iConfiguration          0 
>     bmAttributes         0xc0
>       Self Powered
>     MaxPower                0mA
>     Interface Descriptor:
>       bLength                 9
>       bDescriptorType         4
>       bInterfaceNumber        0
>       bAlternateSetting       0
>       bNumEndpoints           2
>       bInterfaceClass         7 Printer
>       bInterfaceSubClass      1 Printer
>       bInterfaceProtocol      2 Bidirectional
>       iInterface              0 
>       Endpoint Descriptor:
>         bLength                 7
>         bDescriptorType         5
>         bEndpointAddress     0x03  EP 3 OUT
>         bmAttributes            2
>           Transfer Type            Bulk
>           Synch Type               None
>           Usage Type               Data
>         wMaxPacketSize     0x0040  1x 64 bytes
>         bInterval               0
>       Endpoint Descriptor:
>         bLength                 7
>         bDescriptorType         5
>         bEndpointAddress     0x81  EP 1 IN
>         bmAttributes            2
>           Transfer Type            Bulk
>           Synch Type               None
>           Usage Type               Data
>         wMaxPacketSize     0x0040  1x 64 bytes
>         bInterval               0
> 
> Bus 002 Device 001: ID 0000:0000  
> Device Descriptor:
>   bLength                18
>   bDescriptorType         1
>   bcdUSB               1.10
>   bDeviceClass            9 Hub
>   bDeviceSubClass         0 Unused
>   bDeviceProtocol         0 
>   bMaxPacketSize0        64
>   idVendor           0x0000 
>   idProduct          0x0000 
>   bcdDevice            2.06
>   iManufacturer           3 Linux 2.6.19.2 uhci_hcd
>   iProduct                2 UHCI Host Controller
>   iSerial                 1 0000:00:0f.0
>   bNumConfigurations      1
>   Configuration Descriptor:
>     bLength                 9
>     bDescriptorType         2
>     wTotalLength           25
>     bNumInterfaces          1
>     bConfigurationValue     1
>     iConfiguration          0 
>     bmAttributes         0xe0
>       Self Powered
>       Remote Wakeup
>     MaxPower                0mA
>     Interface Descriptor:
>       bLength                 9
>       bDescriptorType         4
>       bInterfaceNumber        0
>       bAlternateSetting       0
>       bNumEndpoints           1
>       bInterfaceClass         9 Hub
>       bInterfaceSubClass      0 Unused
>       bInterfaceProtocol      0 
>       iInterface              0 
>       Endpoint Descriptor:
>         bLength                 7
>         bDescriptorType         5
>         bEndpointAddress     0x81  EP 1 IN
>         bmAttributes            3
>           Transfer Type            Interrupt
>           Synch Type               None
>           Usage Type               Data
>         wMaxPacketSize     0x0002  1x 2 bytes
>         bInterval             255
> Hub Descriptor:
>   bLength               9
>   bDescriptorType      41
>   nNbrPorts             2
>   wHubCharacteristic 0x000a
>     No power switching (usb 1.0)
>     Per-port overcurrent protection
>   bPwrOn2PwrGood        1 * 2 milli seconds
>   bHubContrCurrent      0 milli Ampere
>   DeviceRemovable    0x00
>   PortPwrCtrlMask    0x00 
>  Hub Port Status:
>    Port 1: 0000.0103 power enable connect
>    Port 2: 0000.0303 lowspeed power enable connect
> 
> Bus 001 Device 001: ID 0000:0000  
> Device Descriptor:
>   bLength                18
>   bDescriptorType         1
>   bcdUSB               2.00
>   bDeviceClass            9 Hub
>   bDeviceSubClass         0 Unused
>   bDeviceProtocol         1 Single TT
>   bMaxPacketSize0        64
>   idVendor           0x0000 
>   idProduct          0x0000 
>   bcdDevice            2.06
>   iManufacturer           3 Linux 2.6.19.2 ehci_hcd
>   iProduct                2 EHCI Host Controller
>   iSerial                 1 0000:00:0f.2
>   bNumConfigurations      1
>   Configuration Descriptor:
>     bLength                 9
>     bDescriptorType         2
>     wTotalLength           25
>     bNumInterfaces          1
>     bConfigurationValue     1
>     iConfiguration          0 
>     bmAttributes         0xe0
>       Self Powered
>       Remote Wakeup
>     MaxPower                0mA
>     Interface Descriptor:
>       bLength                 9
>       bDescriptorType         4
>       bInterfaceNumber        0
>       bAlternateSetting       0
>       bNumEndpoints           1
>       bInterfaceClass         9 Hub
>       bInterfaceSubClass      0 Unused
>       bInterfaceProtocol      0 
>       iInterface              0 
>       Endpoint Descriptor:
>         bLength                 7
>         bDescriptorType         5
>         bEndpointAddress     0x81  EP 1 IN
>         bmAttributes            3
>           Transfer Type            Interrupt
>           Synch Type               None
>           Usage Type               Data
>         wMaxPacketSize     0x0002  1x 2 bytes
>         bInterval              12
> Hub Descriptor:
>   bLength               9
>   bDescriptorType      41
>   nNbrPorts             4
>   wHubCharacteristic 0x000a
>     No power switching (usb 1.0)
>     Per-port overcurrent protection
>     TT think time 8 FS bits
>   bPwrOn2PwrGood       10 * 2 milli seconds
>   bHubContrCurrent      0 milli Ampere
>   DeviceRemovable    0x00
>   PortPwrCtrlMask    0x00 
>  Hub Port Status:
>    Port 1: 0000.0000
>    Port 2: 0000.0000
>    Port 3: 0000.0100 power
>    Port 4: 0000.0100 power
> =================================================================
> 
> chek ~ # diff pci-aft pci-bef
> chek ~ # diff usb-bef usb-aft
> 64,120d63
> < Bus 002 Device 003: ID 046d:c00e Logitech, Inc. Optical Mouse
> < Device Descriptor:
> <   bLength                18
> <   bDescriptorType         1
> <   bcdUSB               2.00
> <   bDeviceClass            0 (Defined at Interface level)
> <   bDeviceSubClass         0 
> <   bDeviceProtocol         0 
> <   bMaxPacketSize0         8
> <   idVendor           0x046d Logitech, Inc.
> <   idProduct          0xc00e Optical Mouse
> <   bcdDevice           11.10
> <   iManufacturer           1 Logitech
> <   iProduct                2 USB-PS/2 Optical Mouse
> <   iSerial                 0 
> <   bNumConfigurations      1
> <   Configuration Descriptor:
> <     bLength                 9
> <     bDescriptorType         2
> <     wTotalLength           34
> <     bNumInterfaces          1
> <     bConfigurationValue     1
> <     iConfiguration          0 
> <     bmAttributes         0xa0
> <       Remote Wakeup
> <     MaxPower               98mA
> <     Interface Descriptor:
> <       bLength                 9
> <       bDescriptorType         4
> <       bInterfaceNumber        0
> <       bAlternateSetting       0
> <       bNumEndpoints           1
> <       bInterfaceClass         3 Human Interface Devices
> <       bInterfaceSubClass      1 Boot Interface Subclass
> <       bInterfaceProtocol      2 Mouse
> <       iInterface              0 
> <         HID Device Descriptor:
> <           bLength                 9
> <           bDescriptorType        33
> <           bcdHID               1.10
> <           bCountryCode            0 Not supported
> <           bNumDescriptors         1
> <           bDescriptorType        34 Report
> <           wDescriptorLength      52
> <          Report Descriptors: 
> <            ** UNAVAILABLE **
> <       Endpoint Descriptor:
> <         bLength                 7
> <         bDescriptorType         5
> <         bEndpointAddress     0x81  EP 1 IN
> <         bmAttributes            3
> <           Transfer Type            Interrupt
> <           Synch Type               None
> <           Usage Type               Data
> <         wMaxPacketSize     0x0004  1x 4 bytes
> <         bInterval              10
> < 
> 239a183,304
> > Bus 002 Device 003: ID 046d:c00e Logitech, Inc. Optical Mouse
> > Device Descriptor:
> >   bLength                18
> >   bDescriptorType         1
> >   bcdUSB               2.00
> >   bDeviceClass            0 (Defined at Interface level)
> >   bDeviceSubClass         0 
> >   bDeviceProtocol         0 
> >   bMaxPacketSize0         8
> >   idVendor           0x046d Logitech, Inc.
> >   idProduct          0xc00e Optical Mouse
> >   bcdDevice           11.10
> >   iManufacturer           1 Logitech
> >   iProduct                2 USB-PS/2 Optical Mouse
> >   iSerial                 0 
> >   bNumConfigurations      1
> >   Configuration Descriptor:
> >     bLength                 9
> >     bDescriptorType         2
> >     wTotalLength           34
> >     bNumInterfaces          1
> >     bConfigurationValue     1
> >     iConfiguration          0 
> >     bmAttributes         0xa0
> >       Remote Wakeup
> >     MaxPower               98mA
> >     Interface Descriptor:
> >       bLength                 9
> >       bDescriptorType         4
> >       bInterfaceNumber        0
> >       bAlternateSetting       0
> >       bNumEndpoints           1
> >       bInterfaceClass         3 Human Interface Devices
> >       bInterfaceSubClass      1 Boot Interface Subclass
> >       bInterfaceProtocol      2 Mouse
> >       iInterface              0 
> >         HID Device Descriptor:
> >           bLength                 9
> >           bDescriptorType        33
> >           bcdHID               1.10
> >           bCountryCode            0 Not supported
> >           bNumDescriptors         1
> >           bDescriptorType        34 Report
> >           wDescriptorLength      52
> >          Report Descriptors: 
> >            ** UNAVAILABLE **
> >       Endpoint Descriptor:
> >         bLength                 7
> >         bDescriptorType         5
> >         bEndpointAddress     0x81  EP 1 IN
> >         bmAttributes            3
> >           Transfer Type            Interrupt
> >           Synch Type               None
> >           Usage Type               Data
> >         wMaxPacketSize     0x0004  1x 4 bytes
> >         bInterval              10
> > 
> > Bus 001 Device 004: ID 058f:6362 Alcor Micro Corp. 
> > Device Descriptor:
> >   bLength                18
> >   bDescriptorType         1
> >   bcdUSB               2.00
> >   bDeviceClass            0 (Defined at Interface level)
> >   bDeviceSubClass         0 
> >   bDeviceProtocol         0 
> >   bMaxPacketSize0        64
> >   idVendor           0x058f Alcor Micro Corp.
> >   idProduct          0x6362 
> >   bcdDevice            1.00
> >   iManufacturer           1 Generic
> >   iProduct                2 Mass Storage Device
> >   iSerial                 3 058F312D81B
> >   bNumConfigurations      1
> >   Configuration Descriptor:
> >     bLength                 9
> >     bDescriptorType         2
> >     wTotalLength           32
> >     bNumInterfaces          1
> >     bConfigurationValue     1
> >     iConfiguration          0 
> >     bmAttributes         0x80
> >     MaxPower              100mA
> >     Interface Descriptor:
> >       bLength                 9
> >       bDescriptorType         4
> >       bInterfaceNumber        0
> >       bAlternateSetting       0
> >       bNumEndpoints           2
> >       bInterfaceClass         8 Mass Storage
> >       bInterfaceSubClass      6 SCSI
> >       bInterfaceProtocol     80 Bulk (Zip)
> >       iInterface              0 
> >       Endpoint Descriptor:
> >         bLength                 7
> >         bDescriptorType         5
> >         bEndpointAddress     0x01  EP 1 OUT
> >         bmAttributes            2
> >           Transfer Type            Bulk
> >           Synch Type               None
> >           Usage Type               Data
> >         wMaxPacketSize     0x0200  1x 512 bytes
> >         bInterval               0
> >       Endpoint Descriptor:
> >         bLength                 7
> >         bDescriptorType         5
> >         bEndpointAddress     0x82  EP 2 IN
> >         bmAttributes            2
> >           Transfer Type            Bulk
> >           Synch Type               None
> >           Usage Type               Data
> >         wMaxPacketSize     0x0200  1x 512 bytes
> >         bInterval               0
> > Device Qualifier (for other device speed):
> >   bLength                10
> >   bDescriptorType         6
> >   bcdUSB               2.00
> >   bDeviceClass            0 (Defined at Interface level)
> >   bDeviceSubClass         0 
> >   bDeviceProtocol         0 
> >   bMaxPacketSize0        64
> >   bNumConfigurations      1
> > 
> 302c367
> <    Port 3: 0000.0100 power
> ---
> >    Port 3: 0000.0503 highspeed power enable connect
> =================================================================
> 
> dmesg:
> =================================================================
> uhci_check_and_reset_hc: legsup = 0x2000
> pci 0000:00:0f.0: Performing full reset
> pci 0000:00:0f.1: uhci_check_and_reset_hc: legsup = 0x2000
> pci 0000:00:0f.1: Performing full reset
> lp: driver loaded but no devices found
> Real Time Clock Driver v1.12ac
> Linux agpgart interface v0.101 (c) Dave Jones
> agpgart: Detected ALi M1541 chipset
> agpgart: AGP aperture is 64M @ 0xd8000000
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> parport0: PC-style at 0x378 [PCSPP(,...)]
> lp0: using parport0 (polling).
> loop: loaded (max 8 devices)
> Intel(R) PRO/1000 Network Driver - version 7.2.9-k4
> Copyright (c) 1999-2006 Intel Corporation.
> PPP generic driver version 2.4.2
> PPP Deflate Compression module registered
> PPP BSD Compression module registered
> Linux video capture interface: v2.00
> bttv: driver version 0.9.16 loaded
> bttv: using 8 buffers with 2080k (520 pages) each for capture
> bttv: Bt8xx card found (0).
> PCI: setting IRQ 10 as level-triggered
> PCI: Found IRQ 10 for device 0000:00:0e.0
> PCI: Sharing IRQ 10 with 0000:00:0e.1
> bttv0: Bt878 (rev 17) at 0000:00:0e.0, irq: 10, latency: 32, mmio: 0xe0001000
> bttv0: using: Prolink PixelView PlayTV pro [card=37,insmod option]
> bttv0: gpio: en=00000000, out=00000000 in=009fc0ff [init]
> bttv0: using tuner=69
> bttv0: registered device video0
> bttv0: registered device vbi0
> bttv0: registered device radio0
> bttv0: PLL: 28636363 => 35468950 .. ok
> cx2388x v4l2 driver version 0.0.6 loaded
> cx2388x alsa driver version 0.0.6 loaded
> cx2388x blackbird driver version 0.0.6 loaded
> tuner 0-0060: All bytes are equal. It is not a TEA5767
> tuner 0-0060: chip found @ 0xc0 (bt878 #0 [sw])
> tuner 0-0060: type set to 69 (Tena TNF 5335 and similar models)
> tuner 0-0060: type set to 69 (Tena TNF 5335 and similar models)
> tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw])
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> ALI15X3: IDE controller at PCI slot 0000:00:0d.0
> PCI: setting IRQ 9 as level-triggered
> PCI: Assigned IRQ 9 for device 0000:00:0d.0
> ALI15X3: chipset revision 193
> ALI15X3: not 100% native mode: will probe irqs later
>     ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
>     ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
> Probing IDE interface ide0...
> hda: FUJITSU MPE3084AE, ATA DISK drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> Probing IDE interface ide1...
> hdc: Optiarc DVD RW AD-7173A, ATAPI CD/DVD-ROM drive
> hdd: TEAC CD-W552G, ATAPI CD/DVD-ROM drive
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: max request size: 128KiB
> hda: 16514064 sectors (8455 MB) w/512KiB Cache, CHS=16383/16/63, UDMA(33)
> hda: cache flushes not supported
>  hda: hda1 hda2
> hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, (U)DMA
> Uniform CD-ROM driver Revision: 3.20
> hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, (U)DMA
> ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
> PCI: setting IRQ 11 as level-triggered
> PCI: Found IRQ 11 for device 0000:00:0f.2
> ehci_hcd 0000:00:0f.2: EHCI Host Controller
> drivers/usb/core/inode.c: creating file 'devices'
> drivers/usb/core/inode.c: creating file '001'
> ehci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:0f.2: reset hcs_params 0x2204 dbg=0 cc=2 pcc=2 ordered !ppc 
> ports=4
> ehci_hcd 0000:00:0f.2: reset hcc_params 6872 thresh 7 uframes 256/512/1024
> ehci_hcd 0000:00:0f.2: MWI active
> ehci_hcd 0000:00:0f.2: supports USB remote wakeup
> ehci_hcd 0000:00:0f.2: irq 11, io mem 0xe0003000
> ehci_hcd 0000:00:0f.2: reset command 080002 (park)=0 ithresh=8 period=1024 
> Reset HALT
> ehci_hcd 0000:00:0f.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
> ehci_hcd 0000:00:0f.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb1: default language 0x0409
> usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb1: Product: EHCI Host Controller
> usb usb1: Manufacturer: Linux 2.6.19.2 ehci_hcd
> usb usb1: SerialNumber: 0000:00:0f.2
> usb usb1: uevent
> usb usb1: usb_probe_device
> usb usb1: configuration #1 chosen from 1 choice
> usb usb1: adding 1-0:1.0 (config #1, interface 0)
> usb 1-0:1.0: uevent
> hub 1-0:1.0: usb_probe_interface
> hub 1-0:1.0: usb_probe_interface - got id
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 4 ports detected
> hub 1-0:1.0: standalone hub
> hub 1-0:1.0: no power switching (usb 1.0)
> hub 1-0:1.0: individual port over-current protection
> hub 1-0:1.0: Single TT
> hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
> hub 1-0:1.0: power on to power good time: 20ms
> hub 1-0:1.0: local power source is good
> hub 1-0:1.0: trying to enable port power on non-switchable hub
> hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0000
> drivers/usb/core/inode.c: creating file '001'
> USB Universal Host Controller Interface driver v3.0
> ehci_hcd 0000:00:0f.2: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
> hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
> PCI: setting IRQ 12 as level-triggered
> PCI: Found IRQ 12 for device 0000:00:0f.0
> uhci_hcd 0000:00:0f.0: UHCI Host Controller
> drivers/usb/core/inode.c: creating file '002'
> uhci_hcd 0000:00:0f.0: new USB bus registered, assigned bus number 2
> uhci_hcd 0000:00:0f.0: detected 2 ports
> uhci_hcd 0000:00:0f.0: uhci_check_and_reset_hc: cmd = 0x0000
> uhci_hcd 0000:00:0f.0: Performing full reset
> uhci_hcd 0000:00:0f.0: irq 12, io base 0x0000d000
> usb usb2: default language 0x0409
> usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb2: Product: UHCI Host Controller
> usb usb2: Manufacturer: Linux 2.6.19.2 uhci_hcd
> usb usb2: SerialNumber: 0000:00:0f.0
> usb usb2: uevent
> usb usb2: usb_probe_device
> usb usb2: configuration #1 chosen from 1 choice
> usb usb2: adding 2-0:1.0 (config #1, interface 0)
> usb 2-0:1.0: uevent
> hub 2-0:1.0: usb_probe_interface
> hub 2-0:1.0: usb_probe_interface - got id
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> hub 2-0:1.0: standalone hub
> hub 2-0:1.0: no power switching (usb 1.0)
> hub 2-0:1.0: individual port over-current protection
> hub 2-0:1.0: power on to power good time: 2ms
> hub 2-0:1.0: local power source is good
> hub 2-0:1.0: trying to enable port power on non-switchable hub
> hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
> drivers/usb/core/inode.c: creating file '001'
> PCI: setting IRQ 5 as level-triggered
> PCI: Found IRQ 5 for device 0000:00:0f.1
> PCI: Sharing IRQ 5 with 0000:00:10.0
> uhci_hcd 0000:00:0f.1: UHCI Host Controller
> drivers/usb/core/inode.c: creating file '003'
> uhci_hcd 0000:00:0f.1: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:0f.1: detected 2 ports
> uhci_hcd 0000:00:0f.1: uhci_check_and_reset_hc: cmd = 0x0000
> uhci_hcd 0000:00:0f.1: Performing full reset
> uhci_hcd 0000:00:0f.1: irq 5, io base 0x0000d400
> usb usb3: default language 0x0409
> usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
> usb usb3: Product: UHCI Host Controller
> usb usb3: Manufacturer: Linux 2.6.19.2 uhci_hcd
> usb usb3: SerialNumber: 0000:00:0f.1
> usb usb3: uevent
> usb usb3: usb_probe_device
> usb usb3: configuration #1 chosen from 1 choice
> usb usb3: adding 3-0:1.0 (config #1, interface 0)
> usb 3-0:1.0: uevent
> hub 3-0:1.0: usb_probe_interface
> hub 3-0:1.0: usb_probe_interface - got id
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> hub 3-0:1.0: standalone hub
> hub 3-0:1.0: no power switching (usb 1.0)
> hub 3-0:1.0: individual port over-current protection
> hub 3-0:1.0: power on to power good time: 2ms
> hub 3-0:1.0: local power source is good
> hub 3-0:1.0: trying to enable port power on non-switchable hub
> ehci_hcd 0000:00:0f.2: port 1 full speed --> companion
> ehci_hcd 0000:00:0f.2: GetStatus port 1 status 003801 POWER OWNER sig=j 
> CONNECT
> ehci_hcd 0000:00:0f.2: GetStatus port 2 status 001403 POWER sig=k CSC CONNECT
> hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
> drivers/usb/core/inode.c: creating file '001'
> hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
> ehci_hcd 0000:00:0f.2: port 2 low speed --> companion
> ehci_hcd 0000:00:0f.2: GetStatus port 2 status 003402 POWER OWNER sig=k CSC
> hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0006
> uhci_hcd 0000:00:0f.0: port 1 portsc 009b,00
> hub 2-0:1.0: port 1, status 0101, change 0003, 12 Mb/s
> hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
> usb 2-1: new full speed USB device using uhci_hcd and address 2
> usb 2-1: ep0 maxpacket = 8
> usb 2-1: default language 0x0409
> usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=3
> usb 2-1: Product: Xerox WorkCentre PE114 Series
> usb 2-1: Manufacturer: Xerox
> usb 2-1: SerialNumber: 3561806259......
> usb 2-1: uevent
> usb 2-1: usb_probe_device
> usb 2-1: configuration #1 chosen from 1 choice
> usb 2-1: adding 2-1:1.0 (config #1, interface 0)
> usb 2-1:1.0: uevent
> drivers/usb/core/inode.c: creating file '002'
> uhci_hcd 0000:00:0f.0: port 2 portsc 01ab,00
> hub 2-0:1.0: port 2, status 0301, change 0003, 1.5 Mb/s
> hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
> usb 2-2: new low speed USB device using uhci_hcd and address 3
> usb 2-2: skipped 1 descriptor after interface
> usb 2-2: default language 0x0409
> usb 2-2: new device strings: Mfr=1, Product=2, SerialNumber=0
> usb 2-2: Product: USB-PS/2 Optical Mouse
> usb 2-2: Manufacturer: Logitech
> usb 2-2: uevent
> usb 2-2: usb_probe_device
> usb 2-2: configuration #1 chosen from 1 choice
> usb 2-2: adding 2-2:1.0 (config #1, interface 0)
> usb 2-2:1.0: uevent
> drivers/usb/core/inode.c: creating file '003'
> hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0006
> uhci_hcd 0000:00:0f.1: port 1 portsc 008a,00
> hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
> hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
> uhci_hcd 0000:00:0f.1: port 2 portsc 008a,00
> hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
> hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
> hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
> usbcore: registered new interface driver cdc_acm
> drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB 
> modems and ISDN adapters
> usblp 2-1:1.0: usb_probe_interface
> usblp 2-1:1.0: usb_probe_interface - got id
>  usbdev2.2_ep03: ep_device_release called for usbdev2.2_ep03
>  usbdev2.2_ep81: ep_device_release called for usbdev2.2_ep81
> drivers/usb/core/file.c: looking for a minor, starting at 0
> drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 
> proto 2 vid 0x0924 pid 0x423B
> usbcore: registered new interface driver usblp
> drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
> Initializing USB Mass Storage driver...
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> usbcore: registered new interface driver hiddev
> usbhid 2-2:1.0: usb_probe_interface
> usbhid 2-2:1.0: usb_probe_interface - got id
> input: Logitech USB-PS/2 Optical Mouse as /class/input/input0
> input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on 
> usb-0000:00:0f.0-2
> usbcore: registered new interface driver usbhid
> drivers/usb/input/hid-core.c: v2.6:USB HID core driver
> usbcore: registered new interface driver usbserial
> drivers/usb/serial/usb-serial.c: USB Serial Driver core
> drivers/usb/serial/usb-serial.c: USB Serial support registered for ark3116
> usbcore: registered new interface driver ark3116
> serio: i8042 KBD port at 0x60,0x64 irq 1
> mice: PS/2 mouse device common for all mice
> Advanced Linux Sound Architecture Driver Version 1.0.13 (Tue Nov 28 14:07:24 
> 2006 UTC).
> input: AT Translated Set 2 keyboard as /class/input/input1
> specify port
> snd_mpu401: probe of snd_mpu401.0 failed with error -22
> PCI: Found IRQ 5 for device 0000:00:10.0
> PCI: Sharing IRQ 5 with 0000:00:0f.1
> ALSA device list:
>   #0: ESS ES1938 (Solo-1) rev 0, irq 5
> ip_conntrack version 2.4 (2559 buckets, 20472 max) - 208 bytes per conntrack
> ip_tables: (C) 2000-2006 Netfilter Core Team
> arp_tables: (C) 2002 David S. Miller
> TCP cubic registered
> Initializing XFRM netlink socket
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
> All bugs added by David S. Miller <davem@redhat.com>
> Using IPI Shortcut mode
> Time: tsc clocksource has been installed.
> EXT3-fs: INFO: recovery required on readonly filesystem.
> EXT3-fs: write access will be enabled during recovery.
> usb usb3: suspend_rh (auto-stop)
> kjournald starting.  Commit interval 5 seconds
> EXT3-fs: recovery complete.
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem) readonly.
> Freeing unused kernel memory: 180k freed
> usb usb2: uevent
> usb 2-0:1.0: uevent
> usb 2-1: uevent
> usb 2-1:1.0: uevent
> usb 2-2: uevent
> usb 2-2:1.0: uevent
> usb usb3: uevent
> usb 3-0:1.0: uevent
> usb usb1: uevent
> usb 1-0:1.0: uevent
> nvidia: module license 'NVIDIA' taints kernel.
> NVRM: loading NVIDIA Linux x86 Kernel Module  1.0-7184  Tue Aug  1 18:38:58 
> PDT 2006
> NVRM: CPU does not support the PAT, falling back to MTRRs.
> EXT3 FS on hda2, internal journal
> Adding 152576k swap on /dev/hda1.  Priority:-1 extents:1 across:152576k
> process `named' is using obsolete setsockopt SO_BSDCOMPAT
> agpgart: Found an AGP 1.0 compliant device at 0000:00:00.0.
> agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
> agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
> agpgart: Found an AGP 1.0 compliant device at 0000:00:00.0.
> agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
> agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
> ISO 9660 Extensions: RRIP_1991A
> spurious 8259A interrupt: IRQ7.
> hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0008
> ehci_hcd 0000:00:0f.2: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
> hub 1-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
> hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
> ehci_hcd 0000:00:0f.2: port 3 high speed
> ehci_hcd 0000:00:0f.2: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
> usb 1-3: new high speed USB device using ehci_hcd and address 4
> ehci_hcd 0000:00:0f.2: port 3 high speed
> ehci_hcd 0000:00:0f.2: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
> usb 1-3: default language 0x0409
> usb 1-3: new device strings: Mfr=1, Product=2, SerialNumber=3
> usb 1-3: Product: Mass Storage Device
> usb 1-3: Manufacturer: Generic
> usb 1-3: SerialNumber: 058F312D81B
> usb 1-3: uevent
> usb 1-3: usb_probe_device
> usb 1-3: configuration #1 chosen from 1 choice
> usb 1-3: adding 1-3:1.0 (config #1, interface 0)
> usb 1-3:1.0: uevent
> usb-storage 1-3:1.0: usb_probe_interface
> usb-storage 1-3:1.0: usb_probe_interface - got id
> scsi0 : SCSI emulation for USB Mass Storage devices
> drivers/usb/core/inode.c: creating file '004'
> usb-storage: device found at 4
> usb-storage: waiting for device to settle before scanning
> scsi 0:0:0:0: Direct-Access     Generic  USB SD Reader    1.00 PQ: 0 ANSI: 0
> sd 0:0:0:0: Attached scsi removable disk sda
> sd 0:0:0:0: Attached scsi generic sg0 type 0
> scsi 0:0:0:1: Direct-Access     Generic  USB CF Reader    1.01 PQ: 0 ANSI: 0
> sd 0:0:0:1: Attached scsi removable disk sdb
> sd 0:0:0:1: Attached scsi generic sg1 type 0
> scsi 0:0:0:2: Direct-Access     Generic  USB SM Reader    1.02 PQ: 0 ANSI: 0
> sd 0:0:0:2: Attached scsi removable disk sdc
> sd 0:0:0:2: Attached scsi generic sg2 type 0
> scsi 0:0:0:3: Direct-Access     Generic  USB MS Reader    1.03 PQ: 0 ANSI: 0
> sd 0:0:0:3: Attached scsi removable disk sdd
> sd 0:0:0:3: Attached scsi generic sg3 type 0
> usb-storage: device scan complete
> =================================================================

On Fri, Jun 08, 2007 at 09:42:37PM -0700, bugme-daemon@bugzilla.kernel.org wrote:
> I have old computer :) and bought VIA PCI USB controller. Mouse and 
> printer/scanner works fine, but when i connect a usb drive or card reader, 
> system becomes work very slowly. Deattach of usb drive/reader does not take 
> effect. Disabling udev,dbus and hal services does not take effect too :(

Is there anything showing up in 'top' that is taking more time?

Is there any other USB controller that you can use?  Via controllers are
known to be buggy.

>Is there anything showing up in 'top' that is taking more time?
nothing

>Is there any other USB controller that you can use?
no

ok, i had check this controller on other MB. forks fine

chek linux # lspci -vvv
00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge
        Subsystem: Giga-byte Technology GA-7VAX Mainboard
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 8
        Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
        Capabilities: [a0] AGP version 2.0
                Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
                Command: RQ=32 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- Rate=x1
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 0000f000-00000fff
        Memory behind bridge: da000000-dbffffff
        Prefetchable memory behind bridge: d8000000-d9ffffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (4000ns min, 10000ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at dc000000 (32-bit, prefetchable) [size=4K]
        Capabilities: [44] Vital Product Data
        Capabilities: [4c] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (1000ns min, 63750ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at dc001000 (32-bit, prefetchable) [size=4K]
        Capabilities: [44] Vital Product Data
        Capabilities: [4c] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0c.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61) (prog-if 00 [UHCI])
        Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32, Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 10
        Region 4: I/O ports at d000 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk+ DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0c.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61) (prog-if 00 [UHCI])
        Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32, Cache Line Size: 32 bytes
        Interrupt: pin B routed to IRQ 11
        Region 4: I/O ports at d400 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk+ DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0c.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 63) (prog-if 20 [EHCI])
        Subsystem: VIA Technologies, Inc. USB 2.0
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32, Cache Line Size: 64 bytes
        Interrupt: pin C routed to IRQ 11
        Region 0: Memory at dc002000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk+ DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
        Subsystem: Giga-byte Technology GA-7VAX Mainboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32, Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 10
        Region 4: I/O ports at d800 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
        Subsystem: Giga-byte Technology GA-7VAX Mainboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32, Cache Line Size: 32 bytes
        Interrupt: pin B routed to IRQ 11
        Region 4: I/O ports at dc00 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
        Subsystem: Giga-byte Technology GA-7VAX Mainboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32, Cache Line Size: 32 bytes
        Interrupt: pin C routed to IRQ 11
        Region 4: I/O ports at e000 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
        Subsystem: Giga-byte Technology GA-7VAX Mainboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32, Cache Line Size: 64 bytes
        Interrupt: pin D routed to IRQ 12
        Region 0: Memory at dc003000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
        Subsystem: Giga-byte Technology GA-7VAX Mainboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
        Subsystem: Giga-byte Technology GA-7VAX Mainboard
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32
        Interrupt: pin A routed to IRQ 10
        Region 4: I/O ports at e400 [size=16]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
        Subsystem: Giga-byte Technology GA-7VAX Onboard Audio (Realtek ALC650)
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin C routed to IRQ 11
        Region 0: I/O ports at e800 [size=256]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:13.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
        Subsystem: Realtek Semiconductor Co., Ltd. RT8139
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (8000ns min, 16000ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: I/O ports at ec00 [size=256]
        Region 1: Memory at dc004000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] (rev 15) (prog-if 00 [VGA])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 248 (1250ns min, 250ns max)
        Interrupt: pin A routed to IRQ 10
        Region 0: Memory at da000000 (32-bit, non-prefetchable) [size=16M]
        Region 1: Memory at d8000000 (32-bit, prefetchable) [size=32M]
        [virtual] Expansion ROM at db000000 [disabled] [size=64K]
        Capabilities: [60] Power Management version 1
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [44] AGP version 2.0
                Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
                Command: RQ=32 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- Rate=x1

oh, software enviroment is same :) just i had compile kernel for MB

Still, VIA controllers are known to be buggy and VIA is not willing to work with us to try to fix issues like this. The bugs can be caused by timing issues, so they might not show up on other hardware.

There's really not much we can do here about this, I'm very sorry.