Most recent kernel where this bug did not occur: Distribution: Hardware Environment: Software Environment: Problem Description: Steps to reproduce:
Sorry about the empty bug reposrt. When I try to boot the kvm (CS-64U from ATEN) attached the kernel freeze up when it tries to set the MSI quirk. The motherboard is ASUS PRL=-DLS533. I inserted a usb card and attached the kvm to the usb card and not to the mb usb, but the same freeze up occured. My system is a dual xeon cpu with 2GB of memory (ECC). I run debian and use the unstable branch and the package linux-image-2.6.17-1-686, updated regulary. Here is the full info: /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Xeon(TM) CPU 2.40GHz stepping : 9 cpu MHz : 2399.895 cache size : 512 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid xtpr bogomips : 4803.72 processor : 1 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Xeon(TM) CPU 2.40GHz stepping : 9 cpu MHz : 2399.895 cache size : 512 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid xtpr bogomips : 4798.91 processor : 2 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Xeon(TM) CPU 2.40GHz stepping : 9 cpu MHz : 2399.895 cache size : 512 KB physical id : 3 siblings : 2 core id : 0 cpu cores : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid xtpr bogomips : 4799.03 processor : 3 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Xeon(TM) CPU 2.40GHz stepping : 9 cpu MHz : 2399.895 cache size : 512 KB physical id : 3 siblings : 2 core id : 0 cpu cores : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid xtpr bogomips : 4799.15 /proc/version Linux version 2.6.17-1-686 (Debian 2.6.17-4) (waldi@debian.org) (gcc version 4.1.2 20060708 (prerelease) (Debian 4.1.1-8)) #1 SMP Mon Jul 17 12:45:08 UTC 2006 /proc/mudules ipv6 221760 20 - Live 0xf8b95000 lp 10852 0 - Live 0xf89e6000 button 6544 0 - Live 0xf897d000 ac 4836 0 - Live 0xf898e000 battery 9188 0 - Live 0xf89dd000 ide_generic 1376 0 [permanent], Live 0xf88c5000 ide_cd 35680 0 - Live 0xf8b48000 cdrom 32448 1 ide_cd, Live 0xf8b3f000 evdev 9088 0 - Live 0xf89d9000 i2c_piix4 8464 0 - Live 0xf89ae000 sworks_agp 9120 0 - Live 0xf89aa000 floppy 54276 0 - Live 0xf89eb000 rtc 12340 0 - Live 0xf8994000 agpgart 29864 1 sworks_agp, Live 0xf89d0000 i2c_core 19520 1 i2c_piix4, Live 0xf89a4000 pcspkr 3040 0 - Live 0xf88c8000 8250_pnp 8704 0 - Live 0xf8979000 psmouse 34600 0 - Live 0xf899a000 parport_pc 32132 1 - Live 0xf8935000 serio_raw 6596 0 - Live 0xf8849000 parport 33160 2 lp,parport_pc, Live 0xf896f000 ext3 118152 3 - Live 0xf89b2000 jbd 50260 1 ext3, Live 0xf8980000 mbcache 8324 1 ext3, Live 0xf8931000 dm_mirror 18768 0 - Live 0xf892b000 dm_snapshot 15680 0 - Live 0xf8926000 dm_mod 49976 4 dm_mirror,dm_snapshot, Live 0xf8961000 ide_disk 15072 2 - Live 0xf8824000 sd_mod 18592 6 - Live 0xf88cc000 serverworks 8200 0 [permanent], Live 0xf88c1000 ehci_hcd 28008 0 - Live 0xf88b9000 e1000 100184 0 - Live 0xf890c000 generic 4420 0 [permanent], Live 0xf8859000 ide_core 110888 5 ide_generic,ide_cd,ide_disk,serverworks,generic, Live 0xf88ef000 ohci_hcd 18276 0 - Live 0xf8891000 usbcore 111616 3 ehci_hcd,ohci_hcd, Live 0xf88d2000 tg3 92772 0 - Live 0xf8898000 mptspi 16236 4 - Live 0xf8844000 mptscsih 21504 1 mptspi, Live 0xf883d000 mptbase 46208 2 mptspi,mptscsih, Live 0xf884c000 scsi_transport_spi 22176 1 mptspi, Live 0xf8836000 scsi_mod 123080 4 sd_mod,mptspi,mptscsih,scsi_transport_spi, Live 0xf885d000 thermal 12904 0 - Live 0xf8831000 processor 25512 1 thermal, Live 0xf8829000 fan 4516 0 - Live 0xf881d000 /proc/ioports 0000-001f : dma1 0020-0021 : pic1 0040-0043 : timer0 0050-0053 : timer1 0060-006f : keyboard 0070-0077 : rtc 0080-008f : dma page reg 00a0-00a1 : pic2 00c0-00df : dma2 00f0-00ff : fpu 01f0-01f7 : ide0 02f8-02ff : serial 0378-037a : parport0 037b-037f : parport0 03c0-03df : vga+ 03f6-03f6 : ide0 03f8-03ff : serial 0778-077a : parport0 0c00-0cef : pnp 00:0b 0f50-0f58 : pnp 00:0b 8400-84ff : 0000:0e:07.1 8800-88ff : 0000:0e:07.0 9000-900f : 0000:00:0f.1 03f6-03f6 : ide0 03f8-03ff : serial 0778-077a : parport0 0c00-0cef : pnp 00:0b 0f50-0f58 : pnp 00:0b 8400-84ff : 0000:0e:07.1 8800-88ff : 0000:0e:07.0 9000-900f : 0000:00:0f.1 9000-9007 : ide0 9008-900f : ide1 d400-d4ff : 0000:00:07.0 d800-d83f : 0000:00:06.0 d800-d83f : e1000 e400-e47f : motherboard e400-e403 : PM1a_EVT_BLK e404-e405 : PM1b_CNT_BLK e408-e40b : PM_TMR e410-e417 : GPE1_BLK e800-e807 : piix4_smbus eb00-eb7f : motherboard eb00-eb03 : PM1b_EVT_BLK eb04-eb05 : PM1a_CNT_BLK eb08-eb0f : GPE0_BLK /proc/iomem 00000000-0009efff : System RAM 00000000-00000000 : Crash kernel 0009f000-0009ffff : reserved 000a0000-000bffff : Video RAM area 000c0000-000c7fff : Video ROM 000c8000-000cbfff : Adapter ROM 000f0000-000fffff : System ROM 00100000-7fffafff : System RAM 00100000-00271926 : Kernel code 00271927-002f8b6f : Kernel data 7fffb000-7fffefff : ACPI Tables 7ffff000-7fffffff : ACPI Non-volatile Storage f6800000-f680ffff : 0000:0e:07.1 f7000000-f700ffff : 0000:0e:07.1 f7800000-f780ffff : 0000:0e:07.0 f8000000-f800ffff : 0000:0e:07.0 f8800000-f880ffff : 0000:07:07.0 f8800000-f880ffff : tg3 f9000000-f9000fff : 0000:00:0f.2 f9000000-f9000fff : ohci_hcd f9800000-f9800fff : 0000:00:07.0 fa000000-faffffff : 0000:00:07.0 fb800000-fb81ffff : 0000:00:06.0 fb800000-fb81ffff : e1000 fc000000-fc0000ff : 0000:00:05.3 fc000000-fc0000ff : ehci_hcd fc800000-fc800fff : 0000:00:05.2 fc800000-fc800fff : ohci_hcd fd000000-fd000fff : 0000:00:05.1 fd000000-fd000fff : ohci_hcd fd800000-fd800fff : 0000:00:05.0 fd800000-fd800fff : ohci_hcd fe600000-fe7fffff : 0000:0e:07.1 fe800000-fe9fffff : 0000:0e:07.0 febe0000-febfffff : 0000:00:07.0 fec00000-fec00fff : reserved fee00000-fee00fff : reserved ffff0000-ffffffff : reserved lspci -vvv 00:00.0 Host bridge: Broadcom GCNB-LE Host Bridge (rev 32) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:00.1 Host bridge: Broadcom GCNB-LE Host Bridge Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:05.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10 [OHCI]) Subsystem: ALi Corporation USB 1.1 Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (20000ns max), Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 185 Region 0: Memory at fd800000 (32-bit, non-prefetchable) [size=4K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:05.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10 [OHCI]) Subsystem: ALi Corporation USB 1.1 Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (20000ns max), Cache Line Size: 32 bytes Interrupt: pin C routed to IRQ 193 Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=4K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:05.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if 10 [OHCI]) Subsystem: ALi Corporation USB 1.1 Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (20000ns max), Cache Line Size: 32 bytes Interrupt: pin D routed to IRQ 201 Region 0: Memory at fc800000 (32-bit, non-prefetchable) [size=4K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:05.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: ALi Corporation USB 2.0 Controller Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (20000ns max) Interrupt: pin A routed to IRQ 217 Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port 00:06.0 Ethernet controller: Intel Corporation 82540EM Gigabit Ethernet Controller (rev 02) Subsystem: Intel Corporation 82540EM Gigabit Ethernet Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (63750ns min), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 209 Region 0: Memory at fb800000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at d800 [size=64] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [e4] PCI-X non-bridge device Command: DPERE- ERO+ RBC=512 OST=1 Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz- Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 00:07.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) (prog-if 00 [VGA]) Subsystem: ATI Technologies Inc Rage XL Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 10 Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M] Region 1: I/O ports at d400 [size=256] Region 2: Memory at f9800000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at febe0000 [disabled] [size=128K] Capabilities: [5c] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:0f.0 ISA bridge: Broadcom CSB6 South Bridge (rev a0) Subsystem: Broadcom Unknown device 0201 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 32 00:0f.1 IDE interface: Broadcom CSB6 RAID/IDE Controller (rev a0) (prog-if 8a [Master SecP PriP]) Subsystem: Broadcom Unknown device 0212 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, Cache Line Size: 32 bytes Region 0: I/O ports at <ignored> Region 1: I/O ports at <ignored> Region 2: I/O ports at <ignored> Region 3: I/O ports at <ignored> Region 4: I/O ports at 9000 [size=16] 00:0f.2 USB Controller: Broadcom CSB6 OHCI USB Controller (rev 05) (prog-if 10 [OHCI]) Subsystem: Broadcom Unknown device 0220 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (20000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at f9000000 (32-bit, non-prefetchable) [size=4K] 00:0f.3 Host bridge: Broadcom GCLE-2 Host Bridge Subsystem: Broadcom Unknown device 0230 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:10.0 Host bridge: Broadcom CIOB-X2 PCI-X I/O Bridge (rev 03) Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr+ DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Capabilities: [60] PCI-X non-bridge device Command: DPERE- ERO- RBC=512 OST=8 Status: Dev=00:00.0 64bit+ 133MHz+ SCD- USC- DC=bridge DMMRBC=512 DMOST=8 DMCRS=8 RSCEM- 266MHz- 533MHz- 00:10.2 Host bridge: Broadcom CIOB-X2 PCI-X I/O Bridge (rev 03) Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr+ DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Capabilities: [60] PCI-X non-bridge device Command: DPERE- ERO- RBC=512 OST=8 Status: Dev=00:00.0 64bit+ 133MHz+ SCD- USC- DC=bridge DMMRBC=512 DMOST=8 DMCRS=8 RSCEM- 266MHz- 533MHz- 07:07.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5703X Gigabit Ethernet (rev 02) Subsystem: Broadcom Corporation NetXtreme BCM5703 1000Base-T Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (16000ns min), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 177 Region 0: Memory at f8800000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] PCI-X non-bridge device Command: DPERE- ERO- RBC=2048 OST=1 Status: Dev=07:07.1 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz- Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [50] Vital Product Data Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable- Address: 0020008080200180 Data: 0000 0e:07.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07) Subsystem: LSI Logic / Symbios Logic Unknown device 1000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 72 (4250ns min, 4500ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 169 Region 0: I/O ports at 8800 [size=256] Region 1: Memory at f8000000 (64-bit, non-prefetchable) [size=64K] Region 3: Memory at f7800000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at fe800000 [disabled] [size=2M] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [68] PCI-X non-bridge device Command: DPERE- ERO- RBC=512 OST=1 Status: Dev=0e:07.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=8 DMCRS=16 RSCEM- 266MHz- 533MHz- 0e:07.1 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07) Subsystem: LSI Logic / Symbios Logic Unknown device 1000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 72 (4250ns min, 4500ns max), Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 225 Region 0: I/O ports at 8400 [size=256] Region 1: Memory at f7000000 (64-bit, non-prefetchable) [size=64K] Region 3: Memory at f6800000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at fe600000 [disabled] [size=2M] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [68] PCI-X non-bridge device Command: DPERE- ERO- RBC=512 OST=1 Status: Dev=0e:07.1 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=8 DMCRS=16 RSCEM- 266MHz- 533MHz- /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: FUJITSU Model: MAP3367NP Rev: 0108 Type: Direct-Access ANSI SCSI revision: 03 Host: scsi0 Channel: 00 Id: 01 Lun: 00 Vendor: FUJITSU Model: MAP3367NP Rev: 0108 Type: Direct-Access ANSI SCSI revision: 03 I hope it helps. Eliyahu Sandler
Which USB device driver is in use here? You say it hangs "when it tries to set the MSI quirk". How do you know it's the quirk code which is hanging?
On Mon, August 7, 2006 10:46, bugme-daemon@bugzilla.kernel.org wrote: > http://bugzilla.kernel.org/show_bug.cgi?id=6930 > > akpm@osdl.org changed: > > What |Removed |Added > ---------------------------------------------------------------------------- > CC| |akpm@osdl.org > Owner|other_other@kernel- |greg@kroah.com > |bugs.osdl.org | > > > > ------- Additional Comments From akpm@osdl.org 2006-08-07 00:41 ------- > Which USB device driver is in use here? ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) > You say it hangs "when it tries to set the MSI quirk". How do you know > it's the > quirk code which is hanging? On normal boot it hangs just after issusing the message: PCI: MSI quirk detected. pci_msi_quirk set. When I added initcall_debug to the kernel parameters, I saw that the kernel do not return from setting the pci MSI quirk.
David, that quirk is your speciality :)
Erm, I have no idea why anyone would think I ever had anything to do with message signaled interrupts in PCI. Never touched that code, or even had reason to look at it.
Eliyahu, The MSI code was revised and pretty much rewritten lately (2.6.19 and up). Can you give it a shot? If it fails still, can you please attach a boot trace? --Natalie
Please reopen this bug if it's still present with kernel 2.6.22.