When booting the kernel reports the error: PCI: Cannot allocate resource region 8 of bridge 0000:00:02.0 PCI: Cannot allocate resource region 8 of bridge 0000:00:03.0 PCI: Cannot allocate resource region 8 of bridge 0000:00:03.1 PCI: Cannot allocate resource region 8 of bridge 0000:00:03.2 PCI: Cannot allocate resource region 8 of bridge 0000:00:03.3 The system seems stable and okay so far. But it would be great if it was solved. What is "resource region 8"? lspci command also don't recognize one bridge: "00:01.0 PCI bridge: VIA Technologies, Inc. Unknown device b999 (prog..." The motherboard have 1 x PCI-E x16, 2 x PCI-E x1 and 3 PCI bridges. I have tried the motherboard on the 2.6.14 kernel with same results. Distribution: gentoo linux using original kernel from kernel.org. dmesg: cpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:15 APIC version 16 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x03] address[0xfecc0000] gsi_base[24]) IOAPIC[1]: apic_id 3, version 3, address 0xfecc0000, GSI 24-47 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to flat Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 80000000 (gap: 7ff00000:60100000) Checking aperture... CPU 0: aperture @ d0000000 size 128 MB Built 1 zonelists Kernel command line: root=/dev/sda5 quiet Initializing CPU#0 PID hash table entries: 4096 (order: 12, 131072 bytes) time.c: Using 3.579545 MHz PM timer. time.c: Detected 2006.608 MHz processor. time.c: Using PIT/TSC based timekeeping. Console: colour VGA+ 80x25 Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Memory: 2059236k/2096064k available (2608k kernel code, 36156k reserved, 1090k data, 184k init) Calibrating delay using timer specific routine.. 4021.10 BogoMIPS (lpj=8042215) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) mtrr: v2.0 (20020519) CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 00 Using local APIC timer interrupts. Detected 12.541 MHz APIC timer. testing NMI watchdog ... OK. NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using configuration type 1 PCI: Using MMCONFIG at e0000000 ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEXG._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12) *5 ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 6 7 10 11 12) ACPI: PCI Interrupt Link [ALKA] (IRQs *20) ACPI: PCI Interrupt Link [ALKB] (IRQs *21) ACPI: PCI Interrupt Link [ALKC] (IRQs *22) ACPI: PCI Interrupt Link [ALKD] (IRQs *23) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 13 devices SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Cannot allocate resource region 8 of bridge 0000:00:02.0 PCI: Cannot allocate resource region 8 of bridge 0000:00:03.0 PCI: Cannot allocate resource region 8 of bridge 0000:00:03.1 PCI: Cannot allocate resource region 8 of bridge 0000:00:03.2 PCI: Cannot allocate resource region 8 of bridge 0000:00:03.3 agpgart: Detected AGP bridge 0 agpgart: AGP aperture is 128M @ 0xd0000000 PCI-DMA: Disabling IOMMU. pnp: 00:00: ioport range 0x4000-0x407f could not be reserved pnp: 00:00: ioport range 0x5000-0x500f has been reserved PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:02.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:03.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:03.1 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:03.2 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:03.3 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:01.0 to 64 GSI 16 sharing vector 0xA9 and IRQ 16 ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 27 (level, low) -> IRQ 169 PCI: Via IRQ fixup for 0000:00:02.0, from 3 to 9 PCI: Setting latency timer of device 0000:00:02.0 to 64 GSI 17 sharing vector 0xB1 and IRQ 17 ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 31 (level, low) -> IRQ 177 PCI: Via IRQ fixup for 0000:00:03.0, from 3 to 1 PCI: Setting latency timer of device 0000:00:03.0 to 64 GSI 18 sharing vector 0xB9 and IRQ 18 ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 35 (level, low) -> IRQ 185 PCI: Via IRQ fixup for 0000:00:03.1, from 3 to 9 PCI: Setting latency timer of device 0000:00:03.1 to 64 GSI 19 sharing vector 0xC1 and IRQ 19 ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 39 (level, low) -> IRQ 193 PCI: Via IRQ fixup for 0000:00:03.2, from 3 to 1 PCI: Setting latency timer of device 0000:00:03.2 to 64 GSI 20 sharing vector 0xC9 and IRQ 20 ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 43 (level, low) -> IRQ 201 PCI: Via IRQ fixup for 0000:00:03.3, from 3 to 9 PCI: Setting latency timer of device 0000:00:03.3 to 64 IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ Total HugeTLB memory allocated, 0 Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NTFS driver 2.1.25 [Flags: R/W]. Initializing Cryptographic API io scheduler noop registered io scheduler deadline registered io scheduler cfq registered ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 27 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:02.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[pcie00] Allocate Port Service[pcie01] Allocate Port Service[pcie02] Allocate Port Service[pcie03] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 31 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:00:03.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[pcie00] Allocate Port Service[pcie01] Allocate Port Service[pcie02] Allocate Port Service[pcie03] ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 35 (level, low) -> IRQ 185 PCI: Setting latency timer of device 0000:00:03.1 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[pcie00] Allocate Port Service[pcie01] Allocate Port Service[pcie02] Allocate Port Service[pcie03] ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 39 (level, low) -> IRQ 193 PCI: Setting latency timer of device 0000:00:03.2 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[pcie00] Allocate Port Service[pcie01] Allocate Port Service[pcie02] Allocate Port Service[pcie03] ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 43 (level, low) -> IRQ 201 PCI: Setting latency timer of device 0000:00:03.3 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[pcie00] Allocate Port Service[pcie01] Allocate Port Service[pcie02] Allocate Port Service[pcie03] ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Fan [FAN] (on) Using specific hotkey driver ACPI: Thermal Zone [THRM] (32 C) Real Time Clock Driver v1.12 Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0) Linux agpgart interface v0.101 (c) Dave Jones PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23 GSI 21 sharing vector 0x42 and IRQ 21 ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKD] -> GSI 23 (level, low) -> IRQ 66PCI: Via IRQ fixup for 0000:00:12.0, from 10 to 2 eth0: VIA Rhine II at 0xd8810000, 00:04:61:a0:0e:38, IRQ 66. eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 0021. tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:0f.1 ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20 GSI 22 sharing vector 0x4A and IRQ 22 ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 74PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 10 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 ide0: BM-DMA at 0xdf00-0xdf07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xdf08-0xdf0f, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... hda: _NEC DVD_RW ND-3550A, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... Probing IDE interface ide1... hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 libata version 1.20 loaded. sata_via 0000:00:0f.0: version 1.1 ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 74PCI: Via IRQ fixup for 0000:00:0f.0, from 11 to 10 sata_via 0000:00:0f.0: routed to hard irq line 10 ata1: SATA max UDMA/133 cmd 0xDE00 ctl 0xE402 bmdma 0xDD00 irq 74 ata2: SATA max UDMA/133 cmd 0xE500 ctl 0xDC02 bmdma 0xDD08 irq 74 ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f ata1: dev 0 ATA-7, max UDMA/133, 488397168 sectors: LBA48 ata1: dev 0 configured for UDMA/133 scsi0 : sata_via ata2: no device found (phy stat 00000000) scsi1 : sata_via Vendor: ATA Model: ST3250823AS Rev: 3.03 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) SCSI device sda: drive cache: write back SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sda4 < sda5 sda6 > sd 0:0:0:0: Attached scsi disk sda usbmon: debugfs is not available ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21 GSI 23 sharing vector 0x52 and IRQ 23 ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 82PCI: Via IRQ fixup for 0000:00:10.4, from 5 to 2 ehci_hcd 0000:00:10.4: EHCI Host Controller ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:10.4: irq 82, io mem 0xd8811000 ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) USB Universal Host Controller Interface driver v2.3 ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 82PCI: Via IRQ fixup for 0000:00:10.0, from 10 to 2 uhci_hcd 0000:00:10.0: UHCI Host Controller uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.0: irq 82, io base 0x0000e000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 82PCI: Via IRQ fixup for 0000:00:10.1, from 10 to 2 uhci_hcd 0000:00:10.1: UHCI Host Controller uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.1: irq 82, io base 0x0000e100 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 82PCI: Via IRQ fixup for 0000:00:10.2, from 11 to 2 uhci_hcd 0000:00:10.2: UHCI Host Controller uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.2: irq 82, io base 0x0000e200 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 82PCI: Via IRQ fixup for 0000:00:10.3, from 11 to 2 uhci_hcd 0000:00:10.3: UHCI Host Controller uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:10.3: irq 82, io base 0x0000e300 hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07 13:30:21 2005 UTC). via82xx: Assuming DXS channels with 48k fixed sample rate. Please try dxs_support=5 option and report if it works on your machine. For more details, read ALSA-Configuration.txt. ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22 GSI 24 sharing vector 0x5A and IRQ 24 ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 90PCI: Via IRQ fixup for 0000:00:11.5, from 5 to 10 PCI: Setting latency timer of device 0000:00:11.5 to 64 input: AT Translated Set 2 keyboard as /class/input/input0 input: PS2++ Logitech MX Mouse as /class/input/input1 ALSA device list: #0: VIA 8237 with ALC850 at 0xd400, irq 90 oprofile: using NMI interrupt. NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 9, 2097152 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.4) powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x6 (1400 mV) powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x8 (1350 mV) powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV) cpu_init done, current fid 0xc, vid 0x6 ACPI wakeup devices: PCI0 USB0 USB1 USB2 USB3 USB4 USB5 USB6 USB7 LAN0 AC97 PEXG PEX0 PEX1 PEX2 PEX3 UAR1 ACPI: (supports S0 S1 S3 S4 S5) kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 184k freed Adding 2008116k swap on /dev/sda3. Priority:-1 extents:1 across:2008116k EXT3 FS on sda5, internal journal kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda6, internal journal EXT3-fs: mounted filesystem with ordered data mode. eth0: link up, 10Mbps, half-duplex, lpa 0x0021 lspci -vvv: 00:00.0 Host bridge: VIA Technologies, Inc. K8T890 Host Bridge Subsystem: VIA Technologies, Inc. K8T890 Host Bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 8 Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M] Capabilities: [80] AGP version 3.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] HyperTransport: Slave or Primary Interface !!! Possibly incomplete decoding Command: BaseUnitID=0 UnitCnt=3 MastHost- DefDir- Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=3 Link Config 0: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 Link Config 1: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit Revision ID: 1.02 Capabilities: [58] HyperTransport: Interrupt Discovery and Configuration 00:00.1 Host bridge: VIA Technologies, Inc. K8T890 Host Bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:00.2 Host bridge: VIA Technologies, Inc. K8T890 Host Bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:00.3 Host bridge: VIA Technologies, Inc. K8T890 Host Bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:00.4 Host bridge: VIA Technologies, Inc. K8T890 Host Bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:00.5 PIC: VIA Technologies, Inc. K8T890 I/O APIC Interrupt Controller (prog-if 20 [IO(X)-APIC]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:00.7 Host bridge: VIA Technologies, Inc. K8T890 Host Bridge Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:01.0 PCI bridge: VIA Technologies, Inc. Unknown device b999 (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: fff00000-000fffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- Capabilities: [70] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:02.0 PCI bridge: VIA Technologies, Inc. K8T890 PCI to PCI Bridge Controller (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: fff00000-000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- Capabilities: [40] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <64ns, L1 unlimited Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- Device: MaxPayload 256 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0 Link: Latency L0s <64ns, L1 <1us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x16 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+ Slot: Number 0, PowerLimit 150.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Unknown, PwrInd Unknown, Power- Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [68] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+ Address: 00000000fee00000 Data: 40d9 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel 00:03.0 PCI bridge: VIA Technologies, Inc. K8T890 PCI to PCI Bridge Controller (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: fff00000-000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- Capabilities: [40] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <64ns, L1 unlimited Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- Device: MaxPayload 256 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 1 Link: Latency L0s <64ns, L1 <1us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x4 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+ Slot: Number 0, PowerLimit 25.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Unknown, PwrInd Unknown, Power- Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [68] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+ Address: 00000000fee00000 Data: 40e1 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel 00:03.1 PCI bridge: VIA Technologies, Inc. K8T890 PCI to PCI Bridge Controller (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: fff00000-000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- Capabilities: [40] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <64ns, L1 unlimited Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- Device: MaxPayload 256 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2 Link: Latency L0s <64ns, L1 <1us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x1 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+ Slot: Number 0, PowerLimit 25.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Unknown, PwrInd Unknown, Power- Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [68] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+ Address: 00000000fee00000 Data: 40e9 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel 00:03.2 PCI bridge: VIA Technologies, Inc. K8T890 PCI to PCI Bridge Controller (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: fff00000-000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- Capabilities: [40] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <64ns, L1 unlimited Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- Device: MaxPayload 256 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 3 Link: Latency L0s <64ns, L1 <1us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x1 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+ Slot: Number 0, PowerLimit 25.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Unknown, PwrInd Unknown, Power- Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [68] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+ Address: 00000000fee00000 Data: 4032 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel 00:03.3 PCI bridge: VIA Technologies, Inc. K8T890 PCI to PCI Bridge Controller (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: fff00000-000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- Capabilities: [40] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <64ns, L1 unlimited Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4 Link: Latency L0s <64ns, L1 <1us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x1 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+ Slot: Number 0, PowerLimit 25.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Unknown, PwrInd Unknown, Power- Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [68] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+ Address: 00000000fee00000 Data: 403a Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel 00:0a.0 VGA compatible unclassified device: S3 Inc. 86c864 [Vision 864 DRAM] vers 1 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Region 0: [virtual] Memory at 80000000 (32-bit, non-prefetchable) [size=8M] [virtual] Expansion ROM at 80800000 [disabled] [size=64K] 00:0f.0 IDE interface: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: EPoX Computer Co., Ltd. Unknown device 300e Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Interrupt: pin B routed to IRQ 74 Region 0: I/O ports at de00 [size=8] Region 1: I/O ports at e400 [size=4] Region 2: I/O ports at e500 [size=8] Region 3: I/O ports at dc00 [size=4] Region 4: I/O ports at dd00 [size=16] Region 5: I/O ports at d000 [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: EPoX Computer Co., Ltd. Unknown device 300e Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Interrupt: pin A routed to IRQ 74 Region 4: I/O ports at df00 [size=16] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI]) Subsystem: EPoX Computer Co., Ltd. Unknown device 300e Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size 08 Interrupt: pin A routed to IRQ 82 Region 4: I/O ports at e000 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI]) Subsystem: EPoX Computer Co., Ltd. Unknown device 300e Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size 08 Interrupt: pin A routed to IRQ 82 Region 4: I/O ports at e100 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI]) Subsystem: EPoX Computer Co., Ltd. Unknown device 300e Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size 08 Interrupt: pin B routed to IRQ 82 Region 4: I/O ports at e200 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI]) Subsystem: EPoX Computer Co., Ltd. Unknown device 300e Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size 08 Interrupt: pin B routed to IRQ 82 Region 4: I/O ports at e300 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) (prog-if 20 [EHCI]) Subsystem: EPoX Computer Co., Ltd. Unknown device 300e Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size 10 Interrupt: pin C routed to IRQ 82 Region 0: Memory at d8811000 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South] Subsystem: VIA Technologies, Inc. DFI KT600-AL Motherboard Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60) Subsystem: EPoX Computer Co., Ltd. Unknown device 300e Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin C routed to IRQ 90 Region 0: I/O ports at d400 [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 78) Subsystem: EPoX Computer Co., Ltd. VT6103 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (750ns min, 2000ns max), Cache Line Size 08 Interrupt: pin A routed to IRQ 66 Region 0: I/O ports at d800 [size=256] Region 1: Memory at d8810000 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Capabilities: [80] HyperTransport: Host or Secondary Interface !!! Possibly incomplete decoding Command: WarmRst+ DblEnd- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit Revision ID: 1.02 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
I have the same PCI allocate problem i have a k8t890 mb from Abit(AX8) I do not have the problem with the unknow bridge... that points to my south bridge... from dmesg PCI: Cannot allocate resource region 8 of bridge 0000:00:03.0 PCI: Cannot allocate resource region 8 of bridge 0000:00:03.1 PCI: Cannot allocate resource region 8 of bridge 0000:00:03.2 PCI: Cannot allocate resource region 8 of bridge 0000:00:03.3 from lspci 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South] I'm new to the bug thing, if you need in my system email me, if you have a command for me to run i will :) Oh AND I am gentoo, not sure but that is another similarity...
*** This bug has been marked as a duplicate of 5813 ***