Distribution: Hardware Environment: IBM T41 (though other laptops have same issue),Samsung i500 Software Environment: SuSE 9.3,pilot-link-0.11.8-127 Problem Description: Other maillist history/threads: http://lists.pilot-link.org/pipermail/pilot-link-general/2005-July/002477.html http://lists.pilot-link.org/pipermail/pilot-link-general/2005-August/thread.html **************************************************** So if you bothered to read all the above you can get a small glimse of the crude I have had going on. The phone worked with SuSE 9.0, 9.1, 9.2 but now I have this issue. I have tried three T41 laptops. I have trapped the output of /var/log/messages (see posts please) several times with as much debug as the modules will allow. I am not a programmer but am willing to help. It appears to be a USB kernel module. BUT not specific to UHCI_HCD or EHCI_HCD as I can remove one or the other in the testing and the error is still consistant. I for a while thought it to be a USB controller compat issue in the IBM T41 units but I started (see above for an exaple of my pushback to the Pilot-link group of one direct inquiry to me) getting people with other laptops etc. with the same error / issue. Steps to reproduce: 1)boot system 2)plug phone/palm in 3)load up modules (I blacklist them to keep them from loading) a) modprobe ehci_hcd (phone registers ok at this point) b) modprobe usbserial c) modprobe visor 4) While capturing output from /var/log/messages:>) type "dlpsh -p /dev/usb/ttyUSB0 5) hit sync button on palm/phone 6) Oops reports in /var/log/messages and keyboard is lost on system. The above test can be repeated every time, with ehci_hcd or uhci_hcd. With a SuSE stock kernel or one compiled from kernel.org As aluded to in the documentation of the email threads on the pilot-link site, their are other sytems with the same issue (aka other hardware profiles) and I have tried multiple T41 laptops (our corp standard).
Please post the oops you receive here, and reopen the bug. Can you also test 2.6.13-rc6?
Here is the entire test process I ran: Sorry for the length... but it has all the details I can provide: ************************************** lspci -v -v <snip> 0000:00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: IBM: Unknown device 052d Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 11 Region 4: I/O ports at 1800 [size=32] 0000:00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: IBM: Unknown device 052d Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 11 Region 4: I/O ports at 1820 [size=32] 0000:00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: IBM: Unknown device 052d Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin C routed to IRQ 11 Region 4: I/O ports at 1840 [size=32] 0000:00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: IBM: Unknown device 052e Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin D routed to IRQ 11 Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] #0a [2080] <snip> *************************************************************************** wizej:~ # uname -a Linux wizej 2.6.13-rc6-T41 #1 Fri Aug 12 14:35:25 EDT 2005 i686 i686 i386 GNU/Linux *************************************************************************** wizej:~ # lsmod |grep hcd wizej:~ # *************************************************************************** modprobe ehci_hcd Aug 12 16:28:32 wizej kernel: ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11 Aug 12 16:28:32 wizej kernel: ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11 Aug 12 16:28:32 wizej kernel: PCI: Setting latency timer of device 0000:00:1d.7 to 64 Aug 12 16:28:32 wizej kernel: ehci_hcd 0000:00:1d.7: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller Aug 12 16:28:32 wizej kernel: ehci_hcd 0000:00:1d.7: debug port 1 Aug 12 16:28:32 wizej kernel: ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 Aug 12 16:28:32 wizej kernel: ehci_hcd 0000:00:1d.7: irq 11, io mem 0xc0000000 Aug 12 16:28:32 wizej kernel: PCI: cache line size of 32 is not supported by device 0000:00:1d.7 Aug 12 16:28:32 wizej kernel: ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004 Aug 12 16:28:32 wizej kernel: hub 1-0:1.0: USB hub found Aug 12 16:28:32 wizej kernel: hub 1-0:1.0: 6 ports detected Aug 12 16:28:32 wizej kernel: usb 1-1: new high speed USB device using ehci_hcd and address 2 Aug 12 16:28:33 wizej kernel: hub 1-1:1.0: USB hub found Aug 12 16:28:33 wizej kernel: hub 1-1:1.0: 4 ports detected modprobe usbserial ********************************************************************** modprobe visor Aug 12 16:30:30 wizej kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for Handspring Visor / Palm OS Aug 12 16:30:30 wizej kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 3.5 Aug 12 16:30:30 wizej kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 5.0 Aug 12 16:30:30 wizej kernel: usbcore: registered new driver visor Aug 12 16:30:30 wizej kernel: drivers/usb/serial/visor.c: USB HandSpring Visor / Palm OS driver v2.1 *********************************************************************** <Plug phone/palm in> Aug 12 16:34:47 wizej kernel: usb 1-1.3: new full speed USB device using ehci_hcd and address 3 Aug 12 16:34:47 wizej kernel: usb 1-1.3: palm_os_4_probe - error -32 getting connection info Aug 12 16:34:47 wizej kernel: visor 1-1.3:1.0: Handspring Visor / Palm OS converter detected Aug 12 16:34:47 wizej kernel: usb 1-1.3: Handspring Visor / Palm OS converter now attached to ttyUSB0 Aug 12 16:34:47 wizej kernel: usb 1-1.3: Handspring Visor / Palm OS converter now attached to ttyUSB1 Aug 12 16:34:47 wizej kernel: usb 1-1.3: palm_os_4_probe - error -32 getting connection info Aug 12 16:34:47 wizej kernel: visor 1-1.3:1.1: Handspring Visor / Palm OS converter detected Aug 12 16:34:47 wizej kernel: usb 1-1.3: Handspring Visor / Palm OS converter now attached to ttyUSB2 Aug 12 16:34:47 wizej kernel: usb 1-1.3: Handspring Visor / Palm OS converter now attached to ttyUSB3 Aug 12 16:34:54 wizej /etc/hotplug.d/ttyUSB0/50-visor.hotplug[4609]: add tty device /class/tty/ttyUSB0 *********************************************************************** modprobe visor *********************************************************************** lsmod |less <snip> Module Size Used by visor 19212 0 ehci_hcd 36488 0 usbserial 31720 1 visor serial_core 23808 1 8250 *********************************************************************** dlpsh -p /dev/usb/ttyUSB0 Aug 12 16:37:16 wizej kernel: visor ttyUSB1: Device lied about number of ports, please use a lower one. Aug 12 16:37:16 wizej kernel: visor ttyUSB1: Device lied about number of ports, please use a lower one. Aug 12 16:37:18 wizej kernel: visor ttyUSB1: Device lied about number of ports, please use a lower one. Aug 12 16:37:18 wizej kernel: visor ttyUSB1: Device lied about number of ports, please use a lower one. Aug 12 16:37:19 wizej kernel: usb 1-1.3: USB disconnect, address 3 Aug 12 16:37:19 wizej kernel: visor ttyUSB0: Handspring Visor / Palm OS converter now disconnected from ttyUSB0 Aug 12 16:37:19 wizej kernel: visor ttyUSB1: Handspring Visor / Palm OS converter now disconnected from ttyUSB1 Aug 12 16:37:19 wizej kernel: visor 1-1.3:1.0: device disconnected Aug 12 16:37:19 wizej kernel: visor ttyUSB2: Handspring Visor / Palm OS converter now disconnected from ttyUSB2 Aug 12 16:37:19 wizej kernel: visor ttyUSB3: Handspring Visor / Palm OS converter now disconnected from ttyUSB3 Aug 12 16:37:19 wizej kernel: visor 1-1.3:1.1: device disconnected Aug 12 16:37:19 wizej kernel: usb 1-1.3: new full speed USB device using ehci_hcd and address 4 Aug 12 16:37:24 wizej kernel: usb 1-1.3: config index 0 descriptor too short (expected 46, got 40) Aug 12 16:37:24 wizej kernel: usb 1-1.3: config 1 descriptor has 1 excess byte, ignoring Aug 12 16:37:24 wizej kernel: usb 1-1.3: config 1 interface 0 altsetting 0 has 3 endpoint descriptors, different from the interface descriptor's value: 4 Aug 12 16:37:24 wizej kernel: usb 1-1.3: string descriptor 0 read error: -32 Aug 12 16:37:24 wizej kernel: usb 1-1.3: string descriptor 0 read error: -32 Aug 12 16:37:24 wizej kernel: usb 1-1.3: string descriptor 0 read error: -32 Aug 12 16:37:24 wizej kernel: usb 1-1.3: can't set config #1, error -32 Aug 12 16:37:24 wizej kernel: usb 1-1.3: new full speed USB device using ehci_hcd and address 5 Aug 12 16:37:25 wizej kernel: visor 1-1.3:1.0: Handspring Visor / Palm OS converter detected Aug 12 16:37:25 wizej kernel: usb 1-1.3: Handspring Visor / Palm OS converter now attached to ttyUSB0 Aug 12 16:37:25 wizej kernel: usb 1-1.3: Handspring Visor / Palm OS converter now attached to ttyUSB1 Aug 12 16:37:32 wizej /etc/hotplug.d/ttyUSB0/50-visor.hotplug[5054]: add tty device /class/tty/ttyUSB0 *********************************************************************** Aug 12 16:38:39 wizej /etc/hotplug.d/ttyUSB0/50-visor.hotplug[5329]: add tty device /class/tty/ttyUSB0 Aug 12 16:38:42 wizej kernel: visor ttyUSB1: Device lied about number of ports, please use a lower one. Aug 12 16:38:42 wizej kernel: visor ttyUSB1: Device lied about number of ports, please use a lower one. Aug 12 16:38:44 wizej kernel: usb 1-1.3: USB disconnect, address 6 Aug 12 16:38:44 wizej kernel: visor ttyUSB0: Handspring Visor / Palm OS converter now disconnected from ttyUSB0 Aug 12 16:38:44 wizej kernel: visor ttyUSB1: Handspring Visor / Palm OS converter now disconnected from ttyUSB1 Aug 12 16:38:44 wizej kernel: visor 1-1.3:1.0: device disconnected Aug 12 16:38:44 wizej kernel: visor ttyUSB2: Handspring Visor / Palm OS converter now disconnected from ttyUSB2 Aug 12 16:38:44 wizej kernel: visor ttyUSB3: Handspring Visor / Palm OS converter now disconnected from ttyUSB3 Aug 12 16:38:44 wizej kernel: visor 1-1.3:1.1: device disconnected Aug 12 16:38:44 wizej kernel: Unable to handle kernel paging request at virtual address 37333194 Aug 12 16:38:44 wizej kernel: printing eip: Aug 12 16:38:44 wizej kernel: c0273541 Aug 12 16:38:44 wizej kernel: *pde = 00000000 Aug 12 16:38:44 wizej kernel: Oops: 0000 [#1] Aug 12 16:38:44 wizej kernel: PREEMPT Aug 12 16:38:44 wizej kernel: Modules linked in: visor ehci_hcd ipt_LOG ipt_limit usbserial sg st pcmcia firmware_class yenta_socket rsrc_nonstatic pcmcia_core ipt_state ipt_REJECT iptable_mangle iptable_filter ip_nat_ftp iptable_nat ip_conntrack_ftp ip_conntrack ip_tables raw1394 ieee1394 ext3 jbd sr_mod sd_mod scsi_mod ide_cd cdrom 8250 serial_core Aug 12 16:38:44 wizej kernel: CPU: 0 Aug 12 16:38:44 wizej kernel: EIP: 0060:[<c0273541>] Not tainted VLI Aug 12 16:38:44 wizej kernel: EFLAGS: 00010246 (2.6.13-rc6-T41) Aug 12 16:38:44 wizej kernel: EIP is at check_tty_count+0x51/0xc0 Aug 12 16:38:44 wizej kernel: eax: 37333120 ebx: 00000000 ecx: e2b53980 edx: e2b53980 Aug 12 16:38:44 wizej kernel: esi: e2b53000 edi: e2b53948 ebp: 00000000 esp: efe05efc Aug 12 16:38:44 wizej kernel: ds: 007b es: 007b ss: 0068 Aug 12 16:38:44 wizej kernel: Process events/0 (pid: 3, threadinfo=efe04000 task=c16ef020) Aug 12 16:38:44 wizej kernel: Stack: 000000ad 0001bd47 efe3f590 c76059d3 000000ad efe04000 e2b53000 c02740a8 Aug 12 16:38:44 wizej kernel: e2b53000 c03cc400 000000ad 00000000 00000000 e2b53944 efe04000 e2b53948 Aug 12 16:38:44 wizej kernel: 00000206 c012e3bd e2b53000 efe05f6c 00000000 c16db658 e2b53000 c0274040 Aug 12 16:38:44 wizej kernel: Call Trace: Aug 12 16:38:44 wizej kernel: [<c02740a8>] do_tty_hangup+0x68/0x400 Aug 12 16:38:44 wizej kernel: [<c012e3bd>] worker_thread+0x1dd/0x2c0 Aug 12 16:38:44 wizej kernel: [<c0274040>] do_tty_hangup+0x0/0x400 Aug 12 16:38:44 wizej kernel: [<c0119db0>] default_wake_function+0x0/0x20 Aug 12 16:38:44 wizej kernel: [<c0119db0>] default_wake_function+0x0/0x20 Aug 12 16:38:44 wizej kernel: [<c012e1e0>] worker_thread+0x0/0x2c0 Aug 12 16:38:44 wizej kernel: [<c0132b5d>] kthread+0xad/0xf0 Aug 12 16:38:44 wizej kernel: [<c0132ab0>] kthread+0x0/0xf0 Aug 12 16:38:44 wizej kernel: [<c010138d>] kernel_thread_helper+0x5/0x18 Aug 12 16:38:44 wizej kernel: Code: 00 39 ca 74 12 90 8d 74 26 00 89 c2 43 8b 00 0f 18 00 90 39 ca 75 f3 b8 00 e0 ff ff 21 e0 ff 48 14 8b 40 08 a8 08 75 5f 8b 46 04 <81> 78 74 04 00 02 00 74 37 8b 96 bc 00 00 00 31 c0 39 da 74 25 Aug 12 16:38:44 wizej kernel: <6>usb 1-1.3: new full speed USB device using ehci_hcd and address 7 Aug 12 16:38:44 wizej kernel: usb 1-1.3: palm_os_4_probe - error -32 getting connection info Aug 12 16:38:44 wizej kernel: visor 1-1.3:1.0: Handspring Visor / Palm OS converter detected Aug 12 16:38:44 wizej kernel: usb 1-1.3: Handspring Visor / Palm OS converter now attached to ttyUSB0 Aug 12 16:38:44 wizej kernel: usb 1-1.3: Handspring Visor / Palm OS converter now attached to ttyUSB1 Aug 12 16:38:51 wizej /etc/hotplug.d/ttyUSB0/50-visor.hotplug[5547]: add tty device /class/tty/ttyUSB0 ***********************************************************************
Please put stuff like that in attachments, not in the comments :(
Follow the description of what the driver is telling you to do, and it should work properly... Anyway, care to enable debugging in the driver: modprobe visor debug=1 and then running the program that causes the oops? Then post (attach as an attachment) the resulting oops here. That should give me some hints as to how to fix this.
I have tried to redirect the klogd messages out into a seperate file and reproduce error in a consistant state but without luck. I do not know if this is related to (how I do not know) change of the debug state to debug=1 but I have not been able to capture the hang. At this time communication just times out. Still looking into what if anything could have changed or what I can do to get the error out for your debuging. I will post when my day-job allows me the time to build the test model to recreate the error.
Ok, going to mark as unreproducable then for now.
I can reproduce the bug with kernel 2.6.13-rc6 . This time it happened after I pressed hotsync, while kpilot was probing the port and generating "Device lied about number of ports" errors in the syslog, then pressed cancel on the pilot device. Also note that the following always occurs in the syslog before a BUG or Oops: Sep 16 20:13:52 thelorax usb 5-1: khubd timed out on ep0in len=40/46 Sep 16 20:13:52 thelorax usb 5-1: config index 0 descriptor too short (expected 46, got 40) Sep 16 20:13:52 thelorax usb 5-1: config 1 descriptor has 1 excess byte, ignoring Sep 16 20:13:52 thelorax usb 5-1: config 1 interface 0 altsetting 0 has 3 endpoint descriptors, different from the interface desncriptor's value: 4 Here's the BUG syslog output: Sep 16 20:14:08 thelorax ------------[ cut here ]------------ Sep 16 20:14:08 thelorax kernel BUG at kernel/workqueue.c:104! Sep 16 20:14:08 thelorax invalid operand: 0000 [#1] Sep 16 20:14:08 thelorax PREEMPT Sep 16 20:14:08 thelorax Modules linked in: visor usbserial kqemu tun ppp_async crc_ccitt sha1 ppp_mppe_mppc ppp_generic slhc smbfs usbhid rtc i8k cpufreq_ondemand cpufreq_performance cpufreq_powersave speedstep_centrino freq_table thermal processor fan ac battery button ipw2200 ieee80211 ieee80211_crypt firmware_class evdev nvidia agpgart uhci_hcd ehci_hcd usbcore Sep 16 20:14:08 thelorax CPU: 0 Sep 16 20:14:08 thelorax EIP: 0060:[<c012937a>] Tainted: P VLI Sep 16 20:14:08 thelorax EFLAGS: 00010217 (2.6.13-rc6) Sep 16 20:14:08 thelorax EIP is at queue_work+0x5a/0x70 Sep 16 20:14:08 thelorax eax: d4338948 ebx: 00000000 ecx: c17e9780 edx: d4338944 Sep 16 20:14:08 thelorax esi: e4670cc0 edi: dea31014 ebp: ea2ef4f8 esp: f6947df4 Sep 16 20:14:08 thelorax ds: 007b es: 007b ss: 0068 Sep 16 20:14:08 thelorax Process khubd (pid: 5558, threadinfo=f6946000 task=f6c7b0a0) Sep 16 20:14:08 thelorax Stack: c01190b7 f8b5d674 00000001 f8b5c1a8 d4338000 f8b5d8a0 f8b5d4a0 00000003 Sep 16 20:14:08 thelorax dea31000 f8bf6fe0 f8bf7000 f89f5196 dea31000 dea31000 dea31014 dea31074 Sep 16 20:14:08 thelorax dea31014 c02712b6 dea31014 c03c794d dea31014 ea2ef464 dea31000 c02712ef Sep 16 20:14:08 thelorax Call Trace: Sep 16 20:14:08 thelorax [<c01190b7>] printk+0x17/0x20 Sep 16 20:14:08 thelorax [<f8b5c1a8>] usb_serial_disconnect+0xb8/0x110 [usbserial] Sep 16 20:14:08 thelorax [<f89f5196>] usb_unbind_interface+0x86/0x90 [usbcore] Sep 16 20:14:08 thelorax [<c02712b6>] __device_release_driver+0x86/0xa0 Sep 16 20:14:08 thelorax [<c02712ef>] device_release_driver+0x1f/0x40 Sep 16 20:14:08 thelorax [<c0270a26>] bus_remove_device+0x76/0x90 Sep 16 20:14:08 thelorax [<c026fa22>] device_del+0x32/0x90 Sep 16 20:14:08 thelorax [<f89fe4ca>] usb_disable_device+0x16a/0x1a0 [usbcore] Sep 16 20:14:08 thelorax [<f89f7f56>] usb_disconnect+0xa6/0x190 [usbcore] Sep 16 20:14:08 thelorax [<f89f97c4>] hub_port_connect_change+0x484/0x4b0 [usbcore] Sep 16 20:14:08 thelorax [<f89f9cd6>] hub_events+0x4e6/0x600 [usbcore] Sep 16 20:14:08 thelorax [<f89f9e15>] hub_thread+0x25/0x130 [usbcore] Sep 16 20:14:08 thelorax [<c012e050>] autoremove_wake_function+0x0/0x60 Sep 16 20:14:08 thelorax [<c012e050>] autoremove_wake_function+0x0/0x60 Sep 16 20:14:08 thelorax [<f89f9df0>] hub_thread+0x0/0x130 [usbcore] Sep 16 20:14:08 thelorax [<c012db7a>] kthread+0xaa/0xb0 Sep 16 20:14:08 thelorax [<c012dad0>] kthread+0x0/0xb0 Sep 16 20:14:08 thelorax [<c0100fad>] kernel_thread_helper+0x5/0x18 Sep 16 20:14:08 thelorax Code: 00 89 0c 24 e8 28 ff ff ff b8 00 e0 ff ff 21 e0 ff 48 14 8b 40 08 a8 08 75 0a 89 d8 8b 5c 24 08 83 c4 0c c3 e8 68 ef 26 00 eb ef <0f> 0b 68 00 2b e1 3a c0 eb c3 8d b6 00 00 00 00 8d bf 00 00 00 Sep 16 20:14:08 thelorax <6>note: khubd[5558] exited with preempt_count 1
Still happen on 2.6.14-rc3?
Due to the lack of compatability with my phone and needing to get the investment back out of the device, AND an unrelated bug in Evolution which stopped me from being able to accept meetings with consistancy, I have had to move back to Windows XP(:>(]. I can not offer any more testing at this time. Thanks to those who offered help. Some day (soon I hope) I will revert back to the OS of my heart.
Ok, am closing then. Please reopen if you can test again.
I still get the BUG in 2.6.14-rc3 . I believe that it might be related to a touchy USB connector, as I don't have as many problems when I hold the connector in tight while trying operations (but the kernel still shouldn't BUG, I guess). Oct 17 16:48:27 thelorax usb 5-1: Handspring Visor / Palm OS converter now attached to ttyUSB0 Oct 17 16:48:27 thelorax usb 5-1: Handspring Visor / Palm OS converter now attached to ttyUSB1 Oct 17 16:48:27 thelorax hub 5-0:1.0: state 5 ports 2 chg 0000 evt 0002 Oct 17 16:48:43 thelorax visor ttyUSB1: Device lied about number of ports, please use a lower one. Oct 17 16:48:45 thelorax visor ttyUSB1: Device lied about number of ports, please use a lower one. Oct 17 16:48:47 thelorax visor ttyUSB1: Device lied about number of ports, please use a lower one. Oct 17 16:48:49 thelorax visor ttyUSB1: Device lied about number of ports, please use a lower one. Oct 17 16:48:50 thelorax hub 1-0:1.0: state 5 ports 8 chg 0000 evt ff80 Oct 17 16:48:50 thelorax ehci_hcd 0000:00:1d.7: GetStatus port 7 status 001803 POWER sig=j CSC CONNECT Oct 17 16:48:50 thelorax hub 1-0:1.0: port 7, status 0501, change 0001, 480 Mb/s Oct 17 16:48:50 thelorax hub 1-0:1.0: debounce: port 7: total 100ms stable 100ms status 0x501 Oct 17 16:48:50 thelorax ehci_hcd 0000:00:1d.7: port 7 full speed --> companion Oct 17 16:48:50 thelorax ehci_hcd 0000:00:1d.7: GetStatus port 7 status 003801 POWER OWNER sig=j CONNECT Oct 17 16:48:50 thelorax hub 5-0:1.0: state 5 ports 2 chg 0000 evt 0002 Oct 17 16:48:50 thelorax uhci_hcd 0000:00:1d.3: port 1 portsc 008b,00 Oct 17 16:48:50 thelorax hub 5-0:1.0: port 1, status 0101, change 0003, 12 Mb/s Oct 17 16:48:50 thelorax usb 5-1: USB disconnect, address 6 Oct 17 16:48:50 thelorax usb 5-1: usb_disable_device nuking all URBs Oct 17 16:48:50 thelorax usb 5-1: unregistering interface 5-1:1.0 Oct 17 16:48:50 thelorax ------------[ cut here ]------------ Oct 17 16:48:50 thelorax kernel BUG at kernel/workqueue.c:104! Oct 17 16:48:50 thelorax invalid operand: 0000 [#1] Oct 17 16:48:50 thelorax PREEMPT Oct 17 16:48:50 thelorax Modules linked in: nvidia agpgart visor usbserial usbhid rtc i8k cpufreq_ondemand cpufreq_performance cpufreq_powersave speedstep_centrino freq_table thermal processor fan ac battery button evdev uhci_hcd ehci_hcd usbcore Oct 17 16:48:50 thelorax CPU: 0 Oct 17 16:48:50 thelorax EIP: 0060:[<c0128eaa>] Tainted: P VLI Oct 17 16:48:50 thelorax EFLAGS: 00010217 (2.6.14-rc3) Oct 17 16:48:50 thelorax EIP is at queue_work+0x5a/0x70 Oct 17 16:48:50 thelorax eax: d7a50948 ebx: 00000000 ecx: c17ea6c0 edx: d7a50944 Oct 17 16:48:50 thelorax esi: dca0d1c0 edi: f6557a14 ebp: e03b0d00 esp: f6d5fdf8 Oct 17 16:48:50 thelorax ds: 007b es: 007b ss: 0068 Oct 17 16:48:50 thelorax Process khubd (pid: 5564, threadinfo=f6d5e000 task=f6b19a90) Oct 17 16:48:50 thelorax Stack: c039c310 f8a57000 00000001 f8a4d148 d7a50000 e03b0c00 00000003 f6557a00 Oct 17 16:48:50 thelorax f8a56fe0 f8a57000 f89f61d6 f6557a00 f6557a00 f6557a14 f6557a7c f6557a14 Oct 17 16:48:50 thelorax c0273056 f6557a14 c03ceb90 f6557a14 e03b0c64 f6557a00 c027308f f6557a14 Oct 17 16:48:50 thelorax Call Trace: Oct 17 16:48:50 thelorax [<c039c310>] klist_release+0x0/0x60 Oct 17 16:48:50 thelorax [<f8a4d148>] usb_serial_disconnect+0xa8/0xe0 [usbserial] Oct 17 16:48:50 thelorax [<f89f61d6>] usb_unbind_interface+0x86/0x90 [usbcore] Oct 17 16:48:50 thelorax [<c0273056>] __device_release_driver+0x86/0xa0 Oct 17 16:48:50 thelorax [<c027308f>] device_release_driver+0x1f/0x40 Oct 17 16:48:50 thelorax [<c0272736>] bus_remove_device+0x76/0x90 Oct 17 16:48:50 thelorax [<c02715a2>] device_del+0x32/0x90 Oct 17 16:48:50 thelorax [<f89ff61a>] usb_disable_device+0x16a/0x1a0 [usbcore] Oct 17 16:48:50 thelorax [<f89f9196>] usb_disconnect+0xa6/0x1a0 [usbcore] Oct 17 16:48:50 thelorax [<f89fa997>] hub_port_connect_change+0x487/0x4c0 [usbcore] Oct 17 16:48:50 thelorax [<f89faeb6>] hub_events+0x4e6/0x600 [usbcore] Oct 17 16:48:50 thelorax [<f89faff5>] hub_thread+0x25/0x130 [usbcore] Oct 17 16:48:50 thelorax [<c012db60>] autoremove_wake_function+0x0/0x60 Oct 17 16:48:50 thelorax [<c012db60>] autoremove_wake_function+0x0/0x60 Oct 17 16:48:50 thelorax [<f89fafd0>] hub_thread+0x0/0x130 [usbcore] Oct 17 16:48:50 thelorax [<c012d68a>] kthread+0xaa/0xb0 Oct 17 16:48:50 thelorax [<c012d5e0>] kthread+0x0/0xb0 Oct 17 16:48:50 thelorax [<c0101009>] kernel_thread_helper+0x5/0xc Oct 17 16:48:50 thelorax Code: 00 89 0c 24 e8 28 ff ff ff b8 00 e0 ff ff 21 e0 ff 48 14 8b 40 08 a8 08 75 0a 89 d8 8b 5c 24 08 83 c4 0c c3 e8 f8 3e 27 00 eb ef <0f> 0b 68 00 eb 55 3b c0 eb c3 8d b6 00 00 00 00 8d bf 00 00 00 Oct 17 16:48:50 thelorax <6>note: khubd[5564] exited with preempt_count 1
ugh, does 2.6.14 fix this?
Due to this bug in part, but also an unrelated error in Evolution injecting email one hour in the future (into MS Exchange and Lotus Notes), I was forced dragging and kicking back to Windows XP. I can not at this time perform any additional testing to the resolution of this issue. What I can offer is this. My hope was to at a minimum leverage the phones full functionality under Windows. Bzzzzz.. not so! Same issue. Plug phone in and try to sync and I bluescreen Windows. IMHO the phone sucks on sync (and of corse out of return policy) but on the bright side I feel better about Linux. Thanks for all your help. Sincerly, "The $500 Cell phone owner with lots of bling factor but no use, owner"
Ok, marking closed as this looks like a hardware issue.