Motherboard: P9A-I/C2550/SAS/4L lsscsi -t -v: [0:0:0:0] disk sas:0x5000c50034367baa /dev/sdb dir: /sys/bus/scsi/devices/0:0:0:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:02:00.0/host0/port-0:0/end_device-0:0/target0:0:0/0:0:0:0] [0:0:1:0] disk sas:0x5000c50034367ba9 /dev/sdc dir: /sys/bus/scsi/devices/0:0:1:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:02:00.0/host0/port-0:1/end_device-0:1/target0:0:1/0:0:1:0] [0:0:2:0] disk sas:0x5000c5003432eafe /dev/sdd dir: /sys/bus/scsi/devices/0:0:2:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:02:00.0/host0/port-0:2/end_device-0:2/target0:0:2/0:0:2:0] [0:0:3:0] disk sas:0x5000c5003432eafd /dev/sde dir: /sys/bus/scsi/devices/0:0:3:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:02:00.0/host0/port-0:3/end_device-0:3/target0:0:3/0:0:3:0] [0:0:4:0] disk sas:0x5000c500741d842a /dev/sdf dir: /sys/bus/scsi/devices/0:0:4:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:02:00.0/host0/port-0:4/end_device-0:4/target0:0:4/0:0:4:0] [0:0:5:0] disk sas:0x5000c500741d8429 /dev/sdg dir: /sys/bus/scsi/devices/0:0:5:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:02:00.0/host0/port-0:5/end_device-0:5/target0:0:5/0:0:5:0] [0:0:6:0] disk sas:0x5000c5003c9335ca /dev/sdh dir: /sys/bus/scsi/devices/0:0:6:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:02:00.0/host0/port-0:6/end_device-0:6/target0:0:6/0:0:6:0] [0:0:7:0] disk sas:0x5000c5003c9335c9 /dev/sdi dir: /sys/bus/scsi/devices/0:0:7:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:02:00.0/host0/port-0:7/end_device-0:7/target0:0:7/0:0:7:0] [2:0:0:0] disk sata: /dev/sda dir: /sys/bus/scsi/devices/2:0:0:0 [/sys/devices/pci0000:00/0000:00:18.0/ata2/host2/target2:0:0/2:0:0:0] [3:0:0:0] disk sas:0x5000c5005d722942 /dev/sdj dir: /sys/bus/scsi/devices/3:0:0:0 [/sys/devices/pci0000:00/0000:00:04.0/0000:01:00.0/host3/port-3:0/end_device-3:0/target3:0:0/3:0:0:0] [3:0:1:0] disk sas:0x5000c5005d722941 /dev/sdk dir: /sys/bus/scsi/devices/3:0:1:0 [/sys/devices/pci0000:00/0000:00:04.0/0000:01:00.0/host3/port-3:1/end_device-3:1/target3:0:1/3:0:1:0] [3:0:2:0] disk sas:0x5000c5005d84e1a6 /dev/sdl dir: /sys/bus/scsi/devices/3:0:2:0 [/sys/devices/pci0000:00/0000:00:04.0/0000:01:00.0/host3/port-3:2/end_device-3:2/target3:0:2/3:0:2:0] [3:0:3:0] disk sas:0x5000c5005d84e1a5 /dev/sdm dir: /sys/bus/scsi/devices/3:0:3:0 [/sys/devices/pci0000:00/0000:00:04.0/0000:01:00.0/host3/port-3:3/end_device-3:3/target3:0:3/3:0:3:0] [3:0:4:0] disk sas:0x5000c5007408d282 /dev/sdn dir: /sys/bus/scsi/devices/3:0:4:0 [/sys/devices/pci0000:00/0000:00:04.0/0000:01:00.0/host3/port-3:4/end_device-3:4/target3:0:4/3:0:4:0] [3:0:5:0] disk sas:0x5000c5007408d281 /dev/sdo dir: /sys/bus/scsi/devices/3:0:5:0 [/sys/devices/pci0000:00/0000:00:04.0/0000:01:00.0/host3/port-3:5/end_device-3:5/target3:0:5/3:0:5:0] [3:0:6:0] disk sas:0x5000c500740c1212 /dev/sdp dir: /sys/bus/scsi/devices/3:0:6:0 [/sys/devices/pci0000:00/0000:00:04.0/0000:01:00.0/host3/port-3:6/end_device-3:6/target3:0:6/3:0:6:0] [3:0:7:0] disk sas:0x5000c500740c1211 /dev/sdq dir: /sys/bus/scsi/devices/3:0:7:0 [/sys/devices/pci0000:00/0000:00:04.0/0000:01:00.0/host3/port-3:7/end_device-3:7/target3:0:7/3:0:7:0] [4:0:0:0] cd/dvd usb: 1-1.3.2:1.0 /dev/sr0 dir: /sys/bus/scsi/devices/4:0:0:0 [/sys/devices/pci0000:00/0000:00:16.0/usb1/1-1/1-1.3/1-1.3.2/1-1.3.2:1.0/host4/target4:0:0/4:0:0:0] [5:0:0:0] disk usb: 1-1.3.3:1.0 /dev/sdr dir: /sys/bus/scsi/devices/5:0:0:0 [/sys/devices/pci0000:00/0000:00:16.0/usb1/1-1/1-1.3/1-1.3.3/1-1.3.3:1.0/host5/target5:0:0/5:0:0:0] [6:0:0:0] disk usb: 1-1.3.4:1.0 /dev/sds dir: /sys/bus/scsi/devices/6:0:0:0 [/sys/devices/pci0000:00/0000:00:16.0/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4:1.0/host6/target6:0:0/6:0:0:0] Relevant dmesg snip: [ 1.274088] mvsas 0000:02:00.0: mvsas: driver version 0.8.16 [ 1.276086] dca service started, version 1.12.1 [ 1.296857] mvsas 0000:02:00.0: mvsas: PCI-E x4, Bandwidth Usage: 5.0 Gbps [ 1.303168] ahci 0000:00:18.0: version 3.0 [ 1.303887] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.2.15-k [ 1.310071] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.318636] ahci 0000:00:18.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl SATA mode [ 1.325008] ahci 0000:00:18.0: flags: 64bit ncq led clo pio deso sadm sds apst [ 1.332076] scsi host1: ahci [ 1.338704] scsi host2: ahci [ 1.345099] ata1: SATA max UDMA/133 abar m2048@0xde412000 port 0xde412100 irq 28 [ 1.351516] ata2: SATA max UDMA/133 abar m2048@0xde412000 port 0xde412180 irq 28 [ 1.535197] usb 1-1: New USB device found, idVendor=8087, idProduct=07db [ 1.541442] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.548138] hub 1-1:1.0: USB hub found [ 1.554581] hub 1-1:1.0: 4 ports detected [ 1.682855] ata1: SATA link down (SStatus 0 SControl 300) [ 1.689116] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 1.696299] ata2.00: ATA-9: TS32GMTS400, N1126I, max UDMA/133 [ 1.700761] igb 0000:00:14.0: added PHC on eth0 [ 1.700763] igb 0000:00:14.0: Intel(R) Gigabit Ethernet Network Connection [ 1.700866] igb 0000:00:14.0: eth0: PBA No: 001800-000 [ 1.700868] igb 0000:00:14.0: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s) [ 1.727495] ata2.00: 62533296 sectors, multi 2: LBA48 NCQ (depth 31/32), AA [ 1.734384] ata2.00: configured for UDMA/133 [ 1.740435] tsc: Refined TSC clocksource calibration: 2393.903 MHz [ 1.740675] scsi 2:0:0:0: Direct-Access ATA TS32GMTS400 6I PQ: 0 ANSI: 5 [ 1.741127] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 1.741163] sd 2:0:0:0: [sda] 62533296 512-byte logical blocks: (32.0 GB/29.8 GiB) [ 1.741356] sd 2:0:0:0: [sda] Write Protect is off [ 1.741359] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.741416] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.771415] sda: sda1 sda2 sda3 [ 1.772620] sd 2:0:0:0: [sda] Attached SCSI disk [ 1.795221] clocksource tsc: mask: 0xffffffffffffffff max_cycles: 0x2281b7b41ef, max_idle_ns: 440795228866 ns [ 1.848857] EXT4-fs (sda2): INFO: recovery required on readonly filesystem [ 1.854997] EXT4-fs (sda2): write access will be enabled during recovery [ 1.862974] usb 1-1.2: new low-speed USB device number 3 using ehci-pci [ 2.048981] igb 0000:00:14.1: added PHC on eth1 [ 2.055033] igb 0000:00:14.1: Intel(R) Gigabit Ethernet Network Connection [ 2.061179] igb 0000:00:14.1: eth1: PBA No: 001800-000 [ 2.067121] igb 0000:00:14.1: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s) [ 2.073980] usb 1-1.2: New USB device found, idVendor=051d, idProduct=0002 [ 2.080015] usb 1-1.2: New USB device strings: Mfr=3, Product=1, SerialNumber=2 [ 2.086172] usb 1-1.2: Product: Back-UPS XS 1300 LCD FW:836.H8 .D USB FW:H8 [ 2.092281] usb 1-1.2: Manufacturer: American Power Conversion [ 2.098478] usb 1-1.2: SerialNumber: BB0820012670 [ 2.112737] hidraw: raw HID events driver (C) Jiri Kosina [ 2.148885] EXT4-fs (sda2): orphan cleanup on readonly fs [ 2.155061] EXT4-fs (sda2): 2 orphan inodes deleted [ 2.161145] EXT4-fs (sda2): recovery complete [ 2.176864] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 2.183027] usb 1-1.3: new high-speed USB device number 4 using ehci-pci [ 2.425276] igb 0000:00:14.2: added PHC on eth2 [ 2.431530] igb 0000:00:14.2: Intel(R) Gigabit Ethernet Network Connection [ 2.438023] igb 0000:00:14.2: eth2: PBA No: 001800-000 [ 2.444316] igb 0000:00:14.2: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s) [ 2.485000] usb 1-1.3: New USB device found, idVendor=046b, idProduct=ff01 [ 2.491400] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.497736] usb 1-1.3: Product: Virtual Hub [ 2.503956] usb 1-1.3: Manufacturer: American Megatrends Inc. [ 2.510176] usb 1-1.3: SerialNumber: serial [ 2.516878] hub 1-1.3:1.0: USB hub found [ 2.522991] hub 1-1.3:1.0: 5 ports detected [ 2.712822] usbcore: registered new interface driver usbhid [ 2.718787] usbhid: USB HID core driver [ 2.797332] igb 0000:00:14.3: added PHC on eth3 [ 2.803157] igb 0000:00:14.3: Intel(R) Gigabit Ethernet Network Connection [ 2.808999] igb 0000:00:14.3: eth3: PBA No: 001800-000 [ 2.814722] igb 0000:00:14.3: Using MSI-X interrupts. 4 rx queue(s), 4 tx queue(s) [ 2.821282] Switched to clocksource tsc [ 2.851520] usb 1-1.3.1: new low-speed USB device number 5 using ehci-pci [ 3.012794] usb 1-1.3.1: New USB device found, idVendor=046b, idProduct=ff10 [ 3.018561] usb 1-1.3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.024327] usb 1-1.3.1: Product: Virtual Keyboard and Mouse [ 3.030071] usb 1-1.3.1: Manufacturer: American Megatrends Inc. [ 3.159691] usb 1-1.3.2: new high-speed USB device number 6 using ehci-pci [ 3.320714] usb 1-1.3.2: New USB device found, idVendor=046b, idProduct=ff20 [ 3.326434] usb 1-1.3.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.332120] usb 1-1.3.2: Product: Virtual Cdrom Device [ 3.337745] usb 1-1.3.2: Manufacturer: American Megatrends Inc. [ 3.343394] usb 1-1.3.2: SerialNumber: AAAABBBBCCCC1 [ 3.475869] usb 1-1.3.3: new high-speed USB device number 7 using ehci-pci [ 3.636901] usb 1-1.3.3: New USB device found, idVendor=046b, idProduct=ff40 [ 3.642636] usb 1-1.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.648426] usb 1-1.3.3: Product: Virtual Floppy Device [ 3.654156] usb 1-1.3.3: Manufacturer: American Megatrends Inc. [ 3.659810] usb 1-1.3.3: SerialNumber: AAAABBBBCCCC2 [ 3.788051] usb 1-1.3.4: new high-speed USB device number 8 using ehci-pci [ 3.949074] usb 1-1.3.4: New USB device found, idVendor=046b, idProduct=ff31 [ 3.954635] usb 1-1.3.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.960087] usb 1-1.3.4: Product: Virtual HardDisk Device [ 3.965503] usb 1-1.3.4: Manufacturer: American Megatrends Inc. [ 3.970899] usb 1-1.3.4: SerialNumber: AAAABBBBCCCC3 [ 8.691723] scsi host0: mvsas [ 8.697850] mvsas 0000:01:00.0: mvsas: driver version 0.8.16 [ 8.703663] mvsas 0000:01:00.0: mvsas: PCI-E x4, Bandwidth Usage: 5.0 Gbps [ 8.707897] sas: phy-0:0 added to port-0:0, phy_mask:0x1 (5000c50034367baa) [ 8.707900] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide port phy map 1 [ 8.727818] sas: phy-0:1 added to port-0:1, phy_mask:0x2 (5000c50034367ba9) [ 8.727823] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide port phy map 2 [ 8.757662] sas: phy-0:2 added to port-0:2, phy_mask:0x4 (5000c5003432eafe) [ 8.757665] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide port phy map 4 [ 8.797395] sas: DOING DISCOVERY on port 0, pid:155 [ 8.797399] sas: DONE DISCOVERY on port 0, pid:155, result:0 [ 8.797448] sas: phy-0:3 added to port-0:3, phy_mask:0x8 (5000c5003432eafd) [ 8.797451] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide port phy map 8 [ 8.847156] sas: phy-0:4 added to port-0:4, phy_mask:0x1 (5000c500741d842a) [ 8.847160] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide port phy map 1 [ 8.867071] sas: phy-0:5 added to port-0:5, phy_mask:0x2 (5000c500741d8429) [ 8.867074] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide port phy map 2 [ 8.896874] sas: DOING DISCOVERY on port 1, pid:155 [ 8.896877] sas: DONE DISCOVERY on port 1, pid:155, result:0 [ 8.896927] sas: phy-0:6 added to port-0:6, phy_mask:0x4 (5000c5003c9335ca) [ 8.896930] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide port phy map 4 [ 8.936699] sas: phy-0:7 added to port-0:7, phy_mask:0x8 (5000c5003c9335c9) [ 8.936702] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide port phy map 8 [ 8.986359] sas: DOING DISCOVERY on port 2, pid:155 [ 8.986363] sas: DONE DISCOVERY on port 2, pid:155, result:0 [ 8.987647] scsi 0:0:0:0: Direct-Access SEAGATE ST32000444SS 0006 PQ: 0 ANSI: 5 [ 8.995126] sas: DOING DISCOVERY on port 3, pid:155 [ 8.995136] sas: DONE DISCOVERY on port 3, pid:155, result:0 [ 8.995145] sas: DOING DISCOVERY on port 4, pid:155 [ 8.995149] sas: DONE DISCOVERY on port 4, pid:155, result:0 [ 8.995161] sas: DOING DISCOVERY on port 5, pid:155 [ 8.995166] sas: DONE DISCOVERY on port 5, pid:155, result:0 [ 8.996181] scsi 0:0:1:0: Direct-Access SEAGATE ST32000444SS 0006 PQ: 0 ANSI: 5 [ 9.003056] sas: DOING DISCOVERY on port 6, pid:155 [ 9.003062] sas: DONE DISCOVERY on port 6, pid:155, result:0 [ 9.003071] sas: DOING DISCOVERY on port 7, pid:155 [ 9.003074] sas: DONE DISCOVERY on port 7, pid:155, result:0 [ 9.004324] scsi 0:0:2:0: Direct-Access SEAGATE ST32000444SS 0006 PQ: 0 ANSI: 5 [ 9.012459] scsi 0:0:3:0: Direct-Access SEAGATE ST32000444SS 0006 PQ: 0 ANSI: 5 [ 9.020051] scsi 0:0:4:0: Direct-Access SEAGATE ST2000NM0001 0002 PQ: 0 ANSI: 6 [ 9.026562] scsi 0:0:5:0: Direct-Access SEAGATE ST2000NM0001 0002 PQ: 0 ANSI: 6 [ 9.033522] scsi 0:0:6:0: Direct-Access SEAGATE ST32000444SS 0006 PQ: 0 ANSI: 5 [ 9.040745] scsi 0:0:7:0: Direct-Access SEAGATE ST32000444SS 0006 PQ: 0 ANSI: 5 [ 9.047242] sd 0:0:0:0: Attached scsi generic sg1 type 0 [ 9.052400] sd 0:0:1:0: Attached scsi generic sg2 type 0 [ 9.052502] sd 0:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 9.053230] sd 0:0:1:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 9.057101] sd 0:0:0:0: [sdb] Write Protect is off [ 9.057104] sd 0:0:0:0: [sdb] Mode Sense: d7 00 10 08 [ 9.058949] sd 0:0:1:0: [sdc] Write Protect is off [ 9.058952] sd 0:0:1:0: [sdc] Mode Sense: d7 00 10 08 [ 9.059533] sd 0:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 9.061023] sd 0:0:1:0: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 9.077443] sdb: sdb1 sdb9 [ 9.080843] sdc: sdc1 sdc9 [ 9.090572] sd 0:0:0:0: [sdb] Attached SCSI disk [ 9.091371] sd 0:0:1:0: [sdc] Attached SCSI disk [ 9.101422] sd 0:0:2:0: Attached scsi generic sg3 type 0 [ 9.105866] sd 0:0:3:0: Attached scsi generic sg4 type 0 [ 9.106006] sd 0:0:2:0: [sdd] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 9.106774] sd 0:0:3:0: [sde] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 9.109925] sd 0:0:2:0: [sdd] Write Protect is off [ 9.109928] sd 0:0:2:0: [sdd] Mode Sense: d7 00 10 08 [ 9.111779] sd 0:0:3:0: [sde] Write Protect is off [ 9.111782] sd 0:0:3:0: [sde] Mode Sense: d7 00 10 08 [ 9.112379] sd 0:0:2:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 9.113844] sd 0:0:3:0: [sde] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 9.133888] sd 0:0:4:0: Attached scsi generic sg5 type 0 [ 9.134050] sd 0:0:4:0: [sdf] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 9.137751] sd 0:0:4:0: [sdf] Write Protect is off [ 9.137754] sd 0:0:4:0: [sdf] Mode Sense: d7 00 10 08 [ 9.138307] sd 0:0:4:0: [sdf] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 9.138761] sdd: sdd1 sdd9 [ 9.142160] sde: sde1 sde9 [ 9.146352] random: nonblocking pool is initialized [ 9.154838] sd 0:0:2:0: [sdd] Attached SCSI disk [ 9.156295] sd 0:0:3:0: [sde] Attached SCSI disk [ 9.168918] sd 0:0:5:0: Attached scsi generic sg6 type 0 [ 9.172961] sd 0:0:6:0: Attached scsi generic sg7 type 0 [ 9.173030] sd 0:0:5:0: [sdg] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 9.173418] sd 0:0:6:0: [sdh] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 9.173786] sdf: sdf1 sdf9 [ 9.176797] sd 0:0:5:0: [sdg] Write Protect is off [ 9.176800] sd 0:0:5:0: [sdg] Mode Sense: d7 00 10 08 [ 9.177650] sd 0:0:6:0: [sdh] Write Protect is off [ 9.177653] sd 0:0:6:0: [sdh] Mode Sense: d7 00 10 08 [ 9.177853] sd 0:0:5:0: [sdg] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 9.181519] sd 0:0:6:0: [sdh] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 9.182154] sd 0:0:4:0: [sdf] Attached SCSI disk [ 9.192969] sdg: sdg1 sdg9 [ 9.202032] sd 0:0:5:0: [sdg] Attached SCSI disk [ 9.202056] sdh: sdh1 sdh9 [ 9.212823] sd 0:0:6:0: [sdh] Attached SCSI disk [ 9.226675] sd 0:0:7:0: Attached scsi generic sg8 type 0 [ 9.227054] sd 0:0:7:0: [sdi] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 9.236118] sd 0:0:7:0: [sdi] Write Protect is off [ 9.240479] sd 0:0:7:0: [sdi] Mode Sense: d7 00 10 08 [ 9.241806] sd 0:0:7:0: [sdi] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 9.253848] sdi: sdi1 sdi9 [ 9.263261] sd 0:0:7:0: [sdi] Attached SCSI disk [ 16.099998] scsi host3: mvsas [ 16.175273] sas: phy-3:0 added to port-3:0, phy_mask:0x1 (5000c5005d722942) [ 16.175277] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide port phy map 1 [ 16.195203] sas: phy-3:1 added to port-3:1, phy_mask:0x2 (5000c5005d722941) [ 16.195206] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide port phy map 2 [ 16.225049] sas: phy-3:2 added to port-3:2, phy_mask:0x4 (5000c5005d84e1a6) [ 16.225052] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide port phy map 4 [ 16.264821] sas: phy-3:3 added to port-3:3, phy_mask:0x8 (5000c5005d84e1a5) [ 16.264824] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide port phy map 8 [ 16.314519] sas: phy-3:4 added to port-3:4, phy_mask:0x1 (5000c5007408d282) [ 16.314523] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide port phy map 1 [ 16.334436] sas: phy-3:5 added to port-3:5, phy_mask:0x2 (5000c5007408d281) [ 16.334439] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide port phy map 2 [ 16.364281] sas: phy-3:6 added to port-3:6, phy_mask:0x4 (5000c500740c1212) [ 16.364285] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide port phy map 4 [ 16.404052] sas: phy-3:7 added to port-3:7, phy_mask:0x8 (5000c500740c1211) [ 16.404055] /home/kernel/COD/linux/drivers/scsi/mvsas/mv_sas.c 1116:set wide port phy map 8 [ 16.453711] sas: DOING DISCOVERY on port 0, pid:6 [ 16.453716] sas: DONE DISCOVERY on port 0, pid:6, result:0 [ 16.453725] sas: DOING DISCOVERY on port 1, pid:6 [ 16.453728] sas: DONE DISCOVERY on port 1, pid:6, result:0 [ 16.453735] sas: DOING DISCOVERY on port 2, pid:6 [ 16.453740] sas: DONE DISCOVERY on port 2, pid:6, result:0 [ 16.453747] sas: DOING DISCOVERY on port 3, pid:6 [ 16.453751] sas: DONE DISCOVERY on port 3, pid:6, result:0 [ 16.453757] sas: DOING DISCOVERY on port 4, pid:6 [ 16.453760] sas: DONE DISCOVERY on port 4, pid:6, result:0 [ 16.453767] sas: DOING DISCOVERY on port 5, pid:6 [ 16.453771] sas: DONE DISCOVERY on port 5, pid:6, result:0 [ 16.453780] sas: DOING DISCOVERY on port 6, pid:6 [ 16.453785] sas: DONE DISCOVERY on port 6, pid:6, result:0 [ 16.453791] sas: DOING DISCOVERY on port 7, pid:6 [ 16.453794] sas: DONE DISCOVERY on port 7, pid:6, result:0 [ 16.454955] scsi 3:0:0:0: Direct-Access SEAGATE ST32000444SS 0006 PQ: 0 ANSI: 5 [ 16.462566] scsi 3:0:1:0: Direct-Access SEAGATE ST32000444SS 0006 PQ: 0 ANSI: 5 [ 16.469684] scsi 3:0:2:0: Direct-Access SEAGATE ST2000NM0001 0002 PQ: 0 ANSI: 6 [ 16.475938] scsi 3:0:3:0: Direct-Access SEAGATE ST2000NM0001 0002 PQ: 0 ANSI: 6 [ 16.482286] scsi 3:0:4:0: Direct-Access SEAGATE ST2000NM0001 0002 PQ: 0 ANSI: 6 [ 16.488166] scsi 3:0:5:0: Direct-Access SEAGATE ST2000NM0001 0002 PQ: 0 ANSI: 6 [ 16.494331] scsi 3:0:6:0: Direct-Access SEAGATE ST2000NM0001 0002 PQ: 0 ANSI: 6 [ 16.500037] scsi 3:0:7:0: Direct-Access SEAGATE ST2000NM0001 0002 PQ: 0 ANSI: 6 [ 16.505321] sd 3:0:0:0: Attached scsi generic sg9 type 0 [ 16.505715] sd 3:0:0:0: [sdj] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 16.509529] sd 3:0:0:0: [sdj] Write Protect is off [ 16.509532] sd 3:0:0:0: [sdj] Mode Sense: d7 00 10 08 [ 16.510861] sd 3:0:0:0: [sdj] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 16.522593] sd 3:0:1:0: Attached scsi generic sg10 type 0 [ 16.522759] sdj: sdj1 sdj9 [ 16.523057] sd 3:0:1:0: [sdk] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 16.528211] sd 3:0:1:0: [sdk] Write Protect is off [ 16.528214] sd 3:0:1:0: [sdk] Mode Sense: d7 00 10 08 [ 16.530029] sd 3:0:1:0: [sdk] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 16.535869] sd 3:0:0:0: [sdj] Attached SCSI disk [ 16.545809] sdk: sdk1 sdk9 [ 16.553421] sd 3:0:1:0: [sdk] Attached SCSI disk [ 16.559721] sd 3:0:2:0: Attached scsi generic sg11 type 0 [ 16.559930] sd 3:0:2:0: [sdl] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 16.560876] sd 3:0:2:0: [sdl] Write Protect is off [ 16.560880] sd 3:0:2:0: [sdl] Mode Sense: d7 00 10 08 [ 16.561424] sd 3:0:2:0: [sdl] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 16.579652] sd 3:0:3:0: Attached scsi generic sg12 type 0 [ 16.584941] sd 3:0:4:0: Attached scsi generic sg13 type 0 [ 16.585205] sd 3:0:4:0: [sdn] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 16.590244] sd 3:0:4:0: [sdn] Write Protect is off [ 16.590247] sd 3:0:4:0: [sdn] Mode Sense: d7 00 10 08 [ 16.590820] sd 3:0:4:0: [sdn] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 16.595308] sd 3:0:3:0: [sdm] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 16.595927] sdl: sdl1 sdl9 [ 16.599987] sd 3:0:3:0: [sdm] Write Protect is off [ 16.599996] sd 3:0:3:0: [sdm] Mode Sense: d7 00 10 08 [ 16.601006] sd 3:0:3:0: [sdm] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 16.611179] sd 3:0:2:0: [sdl] Attached SCSI disk [ 16.621188] sdm: sdm1 sdm9 [ 16.621920] sdn: sdn1 sdn9 [ 16.631919] sd 3:0:3:0: [sdm] Attached SCSI disk [ 16.641101] sd 3:0:4:0: [sdn] Attached SCSI disk [ 16.651243] sd 3:0:5:0: Attached scsi generic sg14 type 0 [ 16.651458] sd 3:0:5:0: [sdo] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 16.652367] sd 3:0:5:0: [sdo] Write Protect is off [ 16.652370] sd 3:0:5:0: [sdo] Mode Sense: d7 00 10 08 [ 16.656289] sd 3:0:5:0: [sdo] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 16.672397] sdo: sdo1 sdo9 [ 16.672628] sd 3:0:6:0: Attached scsi generic sg15 type 0 [ 16.672895] sd 3:0:6:0: [sdp] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 16.672926] sd 3:0:7:0: Attached scsi generic sg16 type 0 [ 16.673456] sd 3:0:7:0: [sdq] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 16.674218] sd 3:0:6:0: [sdp] Write Protect is off [ 16.674222] sd 3:0:6:0: [sdp] Mode Sense: d7 00 10 08 [ 16.678415] sd 3:0:6:0: [sdp] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 16.678646] sd 3:0:7:0: [sdq] Write Protect is off [ 16.678649] sd 3:0:7:0: [sdq] Mode Sense: d7 00 10 08 [ 16.679391] sd 3:0:7:0: [sdq] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 16.718785] sdp: sdp1 sdp9 [ 16.718975] sdq: sdq1 sdq9 [ 16.732110] sd 3:0:6:0: [sdp] Attached SCSI disk [ 16.741467] sd 3:0:7:0: [sdq] Attached SCSI disk [ 16.747488] sd 3:0:5:0: [sdo] Attached SCSI disk And finally reported errors on load: [ 2007.415225] sd 0:0:6:0: [sdh] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 2007.415239] sd 0:0:6:0: [sdh] tag#0 Sense Key : Aborted Command [current] [ 2007.415246] sd 0:0:6:0: [sdh] tag#0 Add. Sense: Ack/nak timeout [ 2007.415252] sd 0:0:6:0: [sdh] tag#0 CDB: Read(10) 28 00 2d 02 9d 24 00 00 dc 00 [ 2007.415257] blk_update_request: I/O error, dev sdh, sector 755146020 [ 2958.428448] sd 0:0:6:0: [sdh] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 2958.428466] sd 0:0:6:0: [sdh] tag#0 Sense Key : Aborted Command [current] [ 2958.428474] sd 0:0:6:0: [sdh] tag#0 Add. Sense: Ack/nak timeout [ 2958.428481] sd 0:0:6:0: [sdh] tag#0 CDB: Read(10) 28 00 08 fe 2f c9 00 00 dd 00 [ 2958.428486] blk_update_request: I/O error, dev sdh, sector 150876105
Created attachment 202131 [details] attachment-706-0.html Okay, I'll move around the cables and see if the problems move with them.
After a check and reseat of all cables, now getting this in dmesg: [ 4386.920825] sd 3:0:4:0: [sdn] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 4386.920834] sd 3:0:4:0: [sdn] tag#0 Sense Key : Aborted Command [current] [ 4386.920841] sd 3:0:4:0: [sdn] tag#0 ASC=0x4b ASCQ=0x20 [ 4386.920847] sd 3:0:4:0: [sdn] tag#0 CDB: Read(10) 28 00 33 03 4f bf 00 00 25 00 [ 4386.920852] blk_update_request: I/O error, dev sdn, sector 855855039
Recently problems very similar to this showed up in a discussion on reddit. See https://www.reddit.com/r/zfs/comments/43z0sn/scrub_knocked_a_drive_offline_flaky_hardware_other/ It kinda looks like Marvell controllers (or the mvsas driver?) are sensitive to cable length. I'm looking at halving the length of my cabling, will report back if the issues resolve.
After much more research and reading, I believe I've found the root issue causing the communication timeouts to the disks. I have not changed any cables (other than reseating everything). I came across several reports of marvell (mvsas) controllers randomly causing issues with load, which mentioned SMART. http://www.spinics.net/lists/linux-ide/msg50075.html https://bugzilla.kernel.org/show_bug.cgi?id=42679 So I decided to stop smartd and try my load tests. I have now gone through three iterations of high-load zfs scrubs along with iotest.sh hammering the array simultaneously with no timeouts or communications issues. I believe this indicates some issue with the driver/controller/disks handling smart commands during load. Do you have any recommendations as how I can test this further? Is there any debug info I can provide?