Bug 15305

Looks like you have CONFIG_FRAMEBUFFER_CONSOLE=m, do you get a console when you load that driver or set it to 'y' instead?

I reconfigured as:

CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
# CONFIG_FONTS is not set

and rebuilt/installed.   Now the system seems to hang.   When I boot, I get the lilo prompt, but when I select the new kernel, the screen dies as soon as the kernel loads and I can no longer access the machine remotely (this wasn't the case before).

One more thing.  .config shows:

#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set

#

Is that correct?

I tried 2.6.33 on this box; the problem is still there, and may even be worse.  The box now hangs at some point after the screen goes blank.

Hm, ugly.  Can you attach your lspci -vv output to this bug?  Also a dmesg from a working boot (maybe one without i915 built in) would be good to get.

Here's the lspci output (the dmesg output is later):

00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface (rev 02)
	Subsystem: Dell Device 019d
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
	Capabilities: [e4] Vendor Specific Information <?>
	Kernel driver in use: agpgart-intel
	Kernel modules: intel-agp

00:02.0 VGA compatible controller: Intel Corporation 82865G Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller])
	Subsystem: Dell Dimension 3000
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
	Region 1: Memory at feb80000 (32-bit, non-prefetchable) [size=512K]
	Region 2: I/O ports at ed98 [size=8]
	Expansion ROM at <unassigned> [disabled]
	Capabilities: [d0] Power Management version 1
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: i915
	Kernel modules: i915

00:06.0 System peripheral: Intel Corporation 82865G/PE/P Processor to I/O Memory Interface (rev 02)
	Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Region 0: Memory at fecf0000 (32-bit, non-prefetchable) [size=4K]

00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
	Subsystem: Dell Device 019d
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 4: I/O ports at ff80 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
	Subsystem: Dell Device 019d
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 19
	Region 4: I/O ports at ff60 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
	Subsystem: Dell Device 019d
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 4: I/O ports at ff20 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
	Subsystem: Dell Device 019d
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin D routed to IRQ 23
	Region 0: Memory at ffa80800 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Debug port: BAR=1 offset=00a0
	Kernel driver in use: ehci_hcd
	Kernel modules: ehci-hcd

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
	I/O behind bridge: 0000d000-0000dfff
	Memory behind bridge: fea00000-feafffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge (rev 02)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0

00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02) (prog-if 8a [Master SecP PriP])
	Subsystem: Dell Device 019d
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 18
	Region 0: I/O ports at 01f0 [size=8]
	Region 1: I/O ports at 03f4 [size=1]
	Region 2: I/O ports at 0170 [size=8]
	Region 3: I/O ports at 0374 [size=1]
	Region 4: I/O ports at ffa0 [size=16]
	Region 5: Memory at feb7fc00 (32-bit, non-prefetchable) [size=1K]
	Kernel driver in use: PIIX_IDE

00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02)
	Subsystem: Dell Device 019d
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin B routed to IRQ 17
	Region 4: I/O ports at eda0 [size=32]
	Kernel driver in use: i801_smbus
	Kernel modules: i2c-i801

00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
	Subsystem: Dell Device 019d
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 17
	Region 0: I/O ports at ee00 [size=256]
	Region 1: I/O ports at edc0 [size=64]
	Region 2: Memory at feb7fa00 (32-bit, non-prefetchable) [size=512]
	Region 3: Memory at feb7f900 (32-bit, non-prefetchable) [size=256]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: Intel ICH
	Kernel modules: snd-intel8x0

01:01.0 Modem: ALi Corporation SmartLink SmartPCI561 56K Modem (prog-if 00 [Generic])
	Subsystem: Smart Link Ltd. Device 5459
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Interrupt: pin A routed to IRQ 22
	Region 0: Memory at feafe000 (32-bit, non-prefetchable) [size=4K]
	Region 1: I/O ports at de00 [size=256]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: serial
	Kernel modules: 8250_pci

01:08.0 Ethernet controller: Intel Corporation 82562EZ 10/100 Ethernet Controller (rev 02)
	Subsystem: Dell Dimension 3000
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 20
	Region 0: Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
	Region 1: I/O ports at ddc0 [size=64]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
	Kernel driver in use: e100
	Kernel modules: e100

and here's the dmseg output:

Linux version 2.6.32.2 (root@kirkwood) (gcc version 4.4.2 (GCC) ) #23 SMP PREEMPT Fri Dec 25 10:27:46 EST 2009
KERNEL supported cpus:
  Intel GenuineIntel
  AMD AuthenticAMD
  NSC Geode by NSC
  Cyrix CyrixInstead
  Centaur CentaurHauls
  Transmeta GenuineTMx86
  Transmeta TransmetaCPU
  UMC UMC UMC UMC
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007fe70000 (usable)
 BIOS-e820: 000000007fe70000 - 000000007fe72000 (ACPI NVS)
 BIOS-e820: 000000007fe72000 - 000000007fe93000 (ACPI data)
 BIOS-e820: 000000007fe93000 - 000000007ff00000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fecf0000 - 00000000fecf1000 (reserved)
 BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
 BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
DMI 2.3 present.
last_pfn = 0x7fe70 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
  00000-9FFFF write-back
  A0000-BFFFF uncachable
  C0000-CBFFF write-protect
  CC000-EFFFF uncachable
  F0000-FFFFF write-protect
MTRR variable ranges enabled:
  0 base 000000000 mask F80000000 write-back
  1 base 07FF00000 mask FFFF00000 uncachable
  2 disabled
  3 disabled
  4 disabled
  5 disabled
  6 disabled
  7 disabled
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-00000000377fe000
 0000000000 - 0000400000 page 4k
 0000400000 - 0037400000 page 2M
 0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 7000-c000
ACPI: RSDP 000feb90 00014 (v00 DELL  )
ACPI: RSDT 000fd28b 00034 (v01 DELL    3000    00000008 ASL  00000061)
ACPI: FACP 000fd2bf 00074 (v01 DELL    3000    00000008 ASL  00000061)
ACPI: DSDT fffcf6b6 024C9 (v01   DELL    dt_ex 00001000 MSFT 0100000D)
ACPI: FACS 7fe70000 00040
ACPI: SSDT fffd1b7f 000A7 (v01   DELL    st_ex 00001000 MSFT 0100000D)
ACPI: APIC 000fd333 0006C (v01 DELL    3000    00000008 ASL  00000061)
ACPI: BOOT 000fd39f 00028 (v01 DELL    3000    00000008 ASL  00000061)
ACPI: Local APIC address 0xfee00000
1158MB HIGHMEM available.
887MB LOWMEM available.
  mapped low ram: 0 - 377fe000
  low ram: 0 - 377fe000
  node 0 low ram: 00000000 - 377fe000
  node 0 bootmap 00008000 - 0000ef00
(8 early reservations) ==> bootmem [0000000000 - 00377fe000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
  #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
  #3 [0001000000 - 0001349894]    TEXT DATA BSS ==> [0001000000 - 0001349894]
  #4 [000009fc00 - 0000100000]    BIOS reserved ==> [000009fc00 - 0000100000]
  #5 [000134a000 - 00013501c0]              BRK ==> [000134a000 - 00013501c0]
  #6 [0000007000 - 0000008000]          PGTABLE ==> [0000007000 - 0000008000]
  #7 [0000008000 - 000000f000]          BOOTMAP ==> [0000008000 - 000000f000]
found SMP MP-table at [c00fe710] fe710
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  Normal   0x00001000 -> 0x000377fe
  HighMem  0x000377fe -> 0x0007fe70
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0: 0x00000000 -> 0x000000a0
    0: 0x00000100 -> 0x0007fe70
On node 0 totalpages: 523792
free_area_init_node: node 0, pgdat c12d1f00, node_mem_map c1352000
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 3968 pages, LIFO batch:0
  Normal zone: 1744 pages used for memmap
  Normal zone: 221486 pages, LIFO batch:31
  HighMem zone: 2317 pages used for memmap
  HighMem zone: 294245 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
4 Processors exceeds NR_CPUS limit of 2
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
Allocating PCI resources starting at 7ff00000 (gap: 7ff00000:7ed00000)
NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 11 pages/cpu @c2400000 s21784 r0 d23272 u2097152
pcpu-alloc: s21784 r0 d23272 u2097152 alloc=1*4194304
pcpu-alloc: [0] 0 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 519699
Kernel command line: auto BOOT_IMAGE=Linux-2.6.32.2 ro root=302
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:0007fe70)
Memory: 2073352k/2095552k available (2052k kernel code, 20724k reserved, 850k data, 284k init, 1186248k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff91000 - 0xfffff000   ( 440 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
    lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
      .init : 0xc12d6000 - 0xc131d000   ( 284 kB)
      .data : 0xc12010bc - 0xc12d5ae8   ( 850 kB)
      .text : 0xc1000000 - 0xc12010bc   (2052 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
Hierarchical RCU implementation.
NR_IRQS:320
Console: colour VGA+ 80x25
console [tty0] enabled
Fast TSC calibration using PIT
Detected 2792.918 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 5585.83 BogoMIPS (lpj=11171672)
Mount-cache hash table entries: 512
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 4 MCE banks
CPU0: Thermal monitoring enabled (TM1)
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20090903
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 03
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5586.29 BogoMIPS (lpj=11172598)
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU1: Thermal monitoring enabled (TM1)
CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 03
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (11172.13 BogoMIPS).
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfbbf8, last bus=1
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: Enabling MCH 'Overflow' Device
pci 0000:00:00.0: reg 10 32bit mmio pref: [0xf0000000-0xf7ffffff]
pci 0000:00:02.0: reg 10 32bit mmio pref: [0xe8000000-0xefffffff]
pci 0000:00:02.0: reg 14 32bit mmio: [0xfeb80000-0xfebfffff]
pci 0000:00:02.0: reg 18 io port: [0xed98-0xed9f]
pci 0000:00:06.0: reg 10 32bit mmio: [0xfecf0000-0xfecf0fff]
pci 0000:00:1d.0: reg 20 io port: [0xff80-0xff9f]
pci 0000:00:1d.1: reg 20 io port: [0xff60-0xff7f]
pci 0000:00:1d.3: reg 20 io port: [0xff20-0xff3f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xffa80800-0xffa80bff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: HPET at 0xfed00000
pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 0880-08bf claimed by ICH4 GPIO
pci 0000:00:1f.1: reg 10 io port: [0x1f0-0x1f7]
pci 0000:00:1f.1: reg 14 io port: [0x3f4-0x3f7]
pci 0000:00:1f.1: reg 18 io port: [0x170-0x177]
pci 0000:00:1f.1: reg 1c io port: [0x374-0x377]
pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf]
pci 0000:00:1f.1: reg 24 32bit mmio: [0xfeb7fc00-0xfeb7ffff]
pci 0000:00:1f.3: reg 20 io port: [0xeda0-0xedbf]
pci 0000:00:1f.5: reg 10 io port: [0xee00-0xeeff]
pci 0000:00:1f.5: reg 14 io port: [0xedc0-0xedff]
pci 0000:00:1f.5: reg 18 32bit mmio: [0xfeb7fa00-0xfeb7fbff]
pci 0000:00:1f.5: reg 1c 32bit mmio: [0xfeb7f900-0xfeb7f9ff]
pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1f.5: PME# disabled
pci 0000:01:01.0: reg 10 32bit mmio: [0xfeafe000-0xfeafefff]
pci 0000:01:01.0: reg 14 io port: [0xde00-0xdeff]
pci 0000:01:01.0: PME# supported from D3hot D3cold
pci 0000:01:01.0: PME# disabled
pci 0000:01:08.0: reg 10 32bit mmio: [0xfeaff000-0xfeafffff]
pci 0000:01:08.0: reg 14 io port: [0xddc0-0xddff]
pci 0000:01:08.0: supports D1 D2
pci 0000:01:08.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:01:08.0: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge io port: [0xd000-0xdfff]
pci 0000:00:1e.0: bridge 32bit mmio: [0xfea00000-0xfeafffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 15)
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
ACPI: WMI: Mapper loaded
PCI: Using ACPI for IRQ routing
hpet clockevent registered
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 64-bit 14.318180 MHz counter
Switching to clocksource tsc
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:0a: io resource (0x800-0x85f) overlaps 0000:00:1f.0 BAR 7 (0x800-0x87f), disabling
pnp 00:0a: io resource (0x860-0x8ff) overlaps 0000:00:1f.0 BAR 7 (0x800-0x87f), disabling
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0x100000-0xffffff could not be reserved
system 00:00: iomem range 0x1000000-0x7fe6ffff could not be reserved
system 00:00: iomem range 0xc0000-0xfffff could not be reserved
system 00:00: iomem range 0xfec00000-0xfec0ffff could not be reserved
system 00:00: iomem range 0xfee00000-0xfee0ffff has been reserved
system 00:00: iomem range 0xfed20000-0xfed8ffff has been reserved
system 00:00: iomem range 0xfecf0000-0xfecf0fff has been reserved
system 00:00: iomem range 0xffb00000-0xffbfffff has been reserved
system 00:00: iomem range 0xffc00000-0xffffffff has been reserved
system 00:0a: ioport range 0xc00-0xc7f has been reserved
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
pci 0000:00:1e.0:   IO window: 0xd000-0xdfff
pci 0000:00:1e.0:   MEM window: 0xfea00000-0xfeafffff
pci 0000:00:1e.0:   PREFETCH window: disabled
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io:  [0xd000-0xdfff]
pci_bus 0000:01: resource 1 mem: [0xfea00000-0xfeafffff]
pci_bus 0000:01: resource 3 io:  [0x00-0xffff]
pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
pci 0000:00:02.0: Boot video device
pci 0000:01:08.0: Firmware left e100 interrupts enabled; disabling
Simple Boot Flag value 0x87 read from CMOS RAM was invalid
Simple Boot Flag at 0x7a set to 0x1
highmem bounce pool size: 64 pages
msgmni has been set to 1734
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
input: Power Button as /class/input/input0
ACPI: Power Button [VBTN]
input: Power Button as /class/input/input1
ACPI: Power Button [PWRF]
processor LNXCPU:00: registered as cooling_device0
processor LNXCPU:01: registered as cooling_device1
Real Time Clock Driver v1.12b
Uniform Multi-Platform E-IDE driver
piix 0000:00:1f.1: IDE controller (0x8086:0x24db rev 0x02)
PIIX_IDE 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
piix 0000:00:1f.1: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7
    ide1: BM-DMA at 0xffa8-0xffaf
Probing IDE interface ide0...
hda: WDC WD5000AAKB-00H8A0, ATA DISK drive
hdb: ST340014A, ATA DISK drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/100 mode selected
Probing IDE interface ide1...
hdc: SONY CD-RW/DVD-ROM CRX330E, ATAPI CD/DVD-ROM drive
hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdc: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide-gd driver 1.18
hda: max request size: 512KiB
hda: 976773168 sectors (500107 MB) w/16384KiB Cache, CHS=60801/255/63
hda: cache flushes supported
 hda: hda1 hda2
hdb: max request size: 512KiB
hdb: 78125000 sectors (40000 MB) w/2048KiB Cache, CHS=16383/255/63
hdb: cache flushes supported
 hdb: hdb1 hdb2 hdb3
ide-cd driver 5.00
ide-cd: hdc: ATAPI 48X DVD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
PNP: PS/2 Controller [PNP0303:KBD] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input2
cpuidle: using governor ladder
TCP cubic registered
Using IPI No-Shortcut mode
input: AT Translated Set 2 keyboard as /class/input/input3
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
EXT3-fs: recovery complete.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (ext3 filesystem) readonly on device 3:2.
Freeing unused kernel memory: 284k freed
dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel 865 Chipset
agpgart-intel 0000:00:00.0: detected 892K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xe8000000
Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
Intel ICH 0000:00:1f.5: setting latency timer to 64
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
e100 0000:01:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
e100 0000:01:08.0: PME# disabled
e100: eth0: e100_probe: addr 0xfeaff000, irq 20, MAC addr 00:11:11:bd:a7:9f
serial 0000:01:01.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
0000:01:01.0: ttyS1 at I/O 0xde28 (irq = 22) is a 8250
0000:01:01.0: ttyS2 at I/O 0xde40 (irq = 22) is a 8250
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
0000:01:01.0: ttyS3 at I/O 0xde50 (irq = 22) is a 8250
Couldn't register serial port 0000:01:01.0: -28
[drm] Initialized drm 1.1.0 20060810
intel8x0_measure_ac97_clock: measured 55626 usecs (2680 samples)
intel8x0: clocking to 48000
ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xffa80800
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
i915 0000:00:02.0: setting latency timer to 64
[drm] set up 0M of stolen space
uhci_hcd: USB Universal Host Controller Interface driver
fb0: inteldrmfb frame buffer device
registered panic notifier
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000ff80
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000ff60
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000ff20
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Adding 1060248k swap on /dev/hda1.  Priority:-1 extents:1 across:1060248k 
usb 1-4: new high speed USB device using ehci_hcd and address 4
usb 1-4: configuration #1 chosen from 1 choice
EXT3 FS on hda2, internal journal
usblp0: USB Bidirectional printer dev 4 if 1 alt 0 proto 2 vid 0x04E8 pid 0x341B
usbcore: registered new interface driver usblp
usb 2-2: new full speed USB device using uhci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice
Linux video capture interface: v2.00
lp0: using parport0 (interrupt-driven).
gspca: main v2.7.0 registered
STV06xx: Probing for a stv06xx device
gspca: probing 046d:08f0
STV06xx: Configuring camera
STV06xx: st6422 sensor detected
STV06xx: Initializing camera
usb 3-1: new low speed USB device using uhci_hcd and address 2
gspca: probe ok
STV06xx: Probing for a stv06xx device
gspca: probing 046d:08f0
STV06xx: Probing for a stv06xx device
gspca: probing 046d:08f0
usbcore: registered new interface driver STV06xx
STV06xx: registered
usb 3-1: configuration #1 chosen from 1 choice
input: HID 413c:3010 as /class/input/input4
generic-usb 0003:413C:3010.0001: input: USB HID v1.00 Mouse [HID 413c:3010] on usb-0000:00:1d.1-1/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
NTFS driver 2.1.29 [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS-fs warning (device hdb2): load_system_files(): Unsupported volume flags 0x4000 encountered.
NTFS-fs error (device hdb2): load_system_files(): Volume has unsupported flags set.  Mounting read-only.  Run chkdsk and mount in Windows.
e100: eth0 NIC Link is Up 100 Mbps Full Duplex
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: unable to find recovery directory /var/lib/nfs/v4recovery
NFSD: starting 90-second grace period
udev: starting version 141
udev: deprecated sysfs layout; update the kernel or disable CONFIG_SYSFS_DEPRECATED; some udev features will not work correctly
Console: switching to colour frame buffer device 160x64
render error detected, EIR: 0x00000010
[drm:i915_handle_error] *ERROR* EIR stuck: 0x00000010, masking
render error detected, EIR: 0x00000010
[drm] DAC-5: set mode 1280x1024 12
IPT INPUT packet died: IN=eth0 OUT= MAC=00:11:11:bd:a7:9f:00:13:a3:38:35:b9:08:00 SRC=17.250.248.38 DST=192.168.2.12 LEN=40 TOS=0x00 PREC=0x00 TTL=50 ID=60705 PROTO=TCP SPT=80 DPT=42044 WINDOW=16384 RES=0x00 ACK RST URGP=0 
IPT INPUT packet died: IN=eth0 OUT= MAC=00:11:11:bd:a7:9f:00:13:a3:38:35:b9:08:00 SRC=17.250.248.34 DST=192.168.2.12 LEN=40 TOS=0x00 PREC=0x00 TTL=241 ID=23526 PROTO=TCP SPT=80 DPT=33258 WINDOW=9300 RES=0x00 ACK RST URGP=0

Next time please use attachments instead of dumping information directly into a comment.

Did you test anything later than 2.6.32.2 in the meantime?

I've tried: 

 2.6.32.7/  2.6.32.8/  2.6.33/	2.6.33.1/

All have the same problem.   In addition, I've a similar problem on another slackware box (this one doesn't hang though), running 2.6.33.1.

I also just tried 2.6.33.2--same issue.  This is still a regression.

commit fd2e8ea597222b8f38ae8948776a61ea7958232e
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Tue Feb 9 14:14:36 2010 +0000

    drm/i915: Increase fb alignment to 64k
    
    An untiled framebuffer must be aligned to 64k. This is normally handled
    by intel_pin_and_fence_fb_obj(), but the intelfb_create() likes to be
    different and do the pinning itself. However, it aligns the buffer
    object incorrectly for pre-i965 chipsets causing a PGTBL_ERR when it is
    installed onto the output.
    
    Fixes:
      KMS error message while initializing modesetting -
      render error detected: EIR: 0x10 [i915]
      http://bugs.freedesktop.org/show_bug.cgi?id=22936
    
    Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
    Cc: stable@kernel.org
    Signed-off-by: Eric Anholt <eric@anholt.net>

commit ac0c6b5ad3b3b513e1057806d4b7627fcc0ecc27
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Thu May 27 13:18:18 2010 +0100

    drm/i915: Rebind bo if currently bound with incorrect alignment.
    
    Whilst pinning the buffer, check that that its current alignment
    matches the requested alignment. If it does not, rebind.
    
    This should clear up any final render errors whilst resuming,
    for reference:
    
      Bug 27070 - [i915] Page table errors with empty ringbuffer
      https://bugs.freedesktop.org/show_bug.cgi?id=27070
    
      Bug 15502 -  render error detected, EIR: 0x00000010
      https://bugzilla.kernel.org/show_bug.cgi?id=15502
    
      Bug 13844 -  i915 error: "render error detected"
      https://bugzilla.kernel.org/show_bug.cgi?id=13844
    
    Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
    Cc: stable@kernel.org
    Signed-off-by: Eric Anholt <eric@anholt.net>