[ 0.651690] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.651692] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.651694] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.651696] pci_bus 0000:00: resource 7 [mem 0x7c000000-0xffffffff] [ 0.651698] pci_bus 0000:11: resource 0 [io 0x3000-0x3fff] [ 0.651700] pci_bus 0000:11: resource 1 [mem 0x7c200000-0x7c3fffff] [ 0.651702] pci_bus 0000:11: resource 2 [mem 0x7c400000-0x7c5fffff 64bit pref] [ 0.651704] pci_bus 0000:12: resource 0 [io 0x2000-0x2fff] [ 0.651706] pci_bus 0000:12: resource 1 [mem 0xfbb00000-0xfbbfffff] [ 0.651707] pci_bus 0000:12: resource 2 [mem 0x7c000000-0x7c1fffff 64bit pref] [ 0.651709] pci_bus 0000:13: resource 0 [io 0xe000-0xefff] [ 0.651711] pci_bus 0000:13: resource 1 [mem 0xfba00000-0xfbafffff] [ 0.651713] pci_bus 0000:13: resource 2 [mem 0xd0b00000-0xd0bfffff 64bit pref] [ 0.651715] pci_bus 0000:15: resource 0 [io 0xd000-0xdfff] [ 0.651717] pci_bus 0000:15: resource 1 [mem 0xfb000000-0xfb9fffff] [ 0.651719] pci_bus 0000:15: resource 2 [mem 0xd0000000-0xd09fffff 64bit pref] [ 0.651721] pci_bus 0000:20: resource 4 [io 0x0000-0x0cf7] [ 0.651722] pci_bus 0000:20: resource 5 [io 0x0d00-0xffff] [ 0.651724] pci_bus 0000:20: resource 6 [mem 0x000a0000-0x000bffff] [ 0.651726] pci_bus 0000:20: resource 7 [mem 0x7c000000-0xffffffff] [ 0.651749] NET: Registered protocol family 2 [ 0.651786] IP route cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.651944] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 0.653046] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.653352] TCP: Hash tables configured (established 262144 bind 65536) [ 0.653357] TCP reno registered [ 0.653362] UDP hash table entries: 1024 (order: 3, 32768 bytes) [ 0.653376] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes) [ 0.653479] NET: Registered protocol family 1 [ 0.653573] RPC: Registered udp transport module. [ 0.653578] RPC: Registered tcp transport module. [ 0.653581] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.653597] pci 0000:00:02.0: Boot video device [ 0.898539] PCI: CLS 64 bytes, default 64 [ 0.898604] Trying to unpack rootfs image as initramfs... [ 0.933504] Freeing initrd memory: 2008k freed [ 0.934984] Intel AES-NI instructions are not detected. [ 0.935083] audit: initializing netlink socket (disabled) [ 0.935096] type=2000 audit(1305583665.757:1): initialized [ 0.938382] VFS: Disk quotas dquot_6.5.2 [ 0.938476] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.939176] NTFS driver 2.1.30 [Flags: R/W]. [ 0.939295] ROMFS MTD (C) 2007 Red Hat, Inc. [ 0.939350] msgmni has been set to 3741 [ 0.940369] async_tx: api initialized (async) [ 0.940490] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.940497] io scheduler noop registered [ 0.940500] io scheduler deadline registered (default) [ 0.940602] pcieport 0000:00:1c.0: setting latency timer to 64 [ 0.940658] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X [ 0.940763] pcieport 0000:00:1c.1: setting latency timer to 64 [ 0.940811] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X [ 0.940913] pcieport 0000:00:1c.2: setting latency timer to 64 [ 0.940961] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X [ 0.941062] pcieport 0000:00:1c.4: setting latency timer to 64 [ 0.941111] pcieport 0000:00:1c.4: irq 43 for MSI/MSI-X [ 0.941330] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.941430] vesafb: mode is 1024x768x8, linelength=1024, pages=41 [ 0.941435] vesafb: scrolling: redraw [ 0.941439] vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0 [ 0.941708] vesafb: framebuffer at 0xc0000000, mapped to 0xffffc90010100000, using 1536k, total 32704k [ 0.973664] Console: switching to colour frame buffer device 128x48 [ 1.005428] fb0: VESA VGA frame buffer device [ 1.005739] intel_idle: MWAIT substates: 0x1120 [ 1.005741] intel_idle: v0.4 model 0x25 [ 1.005742] intel_idle: lapic_timer_reliable_states 0xffffffff [ 1.005962] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 1.006652] ACPI: AC Adapter [AC] (on-line) [ 1.007010] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0 [ 1.007505] ACPI: Power Button [PWRB] [ 1.007785] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1 [ 1.010417] ACPI: Lid Switch [LID0] [ 1.010688] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2 [ 1.011173] ACPI: Sleep Button [SBTN] [ 1.011456] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 1.011896] ACPI: Power Button [PWRF] [ 1.012192] ACPI: acpi_idle yielding to intel_idle [ 1.013806] ERST: Table is not found! [ 1.017124] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.018707] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 1.019329] ACPI: Battery Slot [BAT0] (battery present) [ 1.080601] Linux agpgart interface v0.103 [ 1.082500] brd: module loaded [ 1.083460] loop: module loaded [ 1.096070] Loading iSCSI transport class v2.0-870. [ 1.109277] ahci 0000:00:1f.2: version 3.0 [ 1.109296] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1.122302] ahci 0000:00:1f.2: irq 44 for MSI/MSI-X [ 1.133153] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 1.146210] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck pm led clo pio slum part ems sxs apst [ 1.146218] ahci 0000:00:1f.2: setting latency timer to 64 [ 1.157105] scsi0 : ahci [ 1.157260] scsi1 : ahci [ 1.157394] scsi2 : ahci [ 1.157531] scsi3 : ahci [ 1.157672] scsi4 : ahci [ 1.157808] scsi5 : ahci [ 1.158106] ata1: SATA max UDMA/133 abar m2048@0xfbc06000 port 0xfbc06100 irq 44 [ 1.158109] ata2: SATA max UDMA/133 abar m2048@0xfbc06000 port 0xfbc06180 irq 44 [ 1.158112] ata3: SATA max UDMA/133 abar m2048@0xfbc06000 port 0xfbc06200 irq 44 [ 1.158115] ata4: SATA max UDMA/133 abar m2048@0xfbc06000 port 0xfbc06280 irq 44 [ 1.158118] ata5: SATA max UDMA/133 abar m2048@0xfbc06000 port 0xfbc06300 irq 44 [ 1.158121] ata6: SATA max UDMA/133 abar m2048@0xfbc06000 port 0xfbc06380 irq 44 [ 1.158153] ata1: ata_sff_flush_pio_task: EXIT [ 1.158155] ata2: ata_sff_flush_pio_task: EXIT [ 1.158187] ata3: ata_sff_flush_pio_task: EXIT [ 1.158218] ata4: ata_sff_flush_pio_task: EXIT [ 1.158255] ata5: ata_sff_flush_pio_task: EXIT [ 1.158295] ata6: ata_sff_flush_pio_task: EXIT [ 1.160636] i8042: PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2] at 0x60,0x64 irq 1,12 [ 1.186763] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.186773] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.186916] mousedev: PS/2 mouse device common for all mice [ 1.187174] rtc_cmos 00:03: RTC can wake from S4 [ 1.364956] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 1.366778] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4 [ 1.387513] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs [ 1.398907] md: linear personality registered for level -1 [ 1.412101] md: raid0 personality registered for level 0 [ 1.423112] md: raid1 personality registered for level 1 [ 1.433725] md: raid10 personality registered for level 10 [ 1.444160] md: raid6 personality registered for level 6 [ 1.454398] md: raid5 personality registered for level 5 [ 1.463540] ata5: SATA link down (SStatus 0 SControl 300) [ 1.463575] ata3: SATA link down (SStatus 0 SControl 300) [ 1.463616] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.463621] ata1.00: ata_dev_read_id: ENTER [ 1.463646] ata4: SATA link down (SStatus 0 SControl 300) [ 1.463676] ata6: SATA link down (SStatus 0 SControl 300) [ 1.463707] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.463713] ata2.00: ata_dev_read_id: ENTER [ 1.464794] ata1: ata_sff_flush_pio_task: EXIT [ 1.464797] ata1.00: ata_dev_configure: ENTER [ 1.464802] ata1.00: ata_acpi_push_id: ix = 0, port#: 0 [ 1.464862] ata1.00: ata_dev_get_GTF: ENTER: port#: 0 [ 1.464871] ata1.00: ata_dev_get_GTF: returning gtf=ffff880076f9def8, gtf_count=1 [ 1.466733] ata2: ata_sff_flush_pio_task: EXIT [ 1.466735] ata2.00: ata_dev_configure: ENTER [ 1.466739] ata2.00: ata_dev_configure: cfg 49:0f00 82:0210 83:5000 84:4000 85:0210 86:1000 87:4000 88:203f [ 1.466742] ata2.00: ATAPI: PLDS DVD+/-RW DS-8A5SH, XD12, max UDMA/100 [ 1.466748] ata1: ata_sff_flush_pio_task: EXIT [ 1.466751] ata1.00: ACPI cmd ef/5a:00:00:00:00:a0 (SET FEATURES) succeeded [ 1.466753] ata1.00: ata_dev_read_id: ENTER [ 1.467636] ata2: ata_sff_flush_pio_task: EXIT [ 1.467641] ata2.00: ata_dev_read_id: ENTER [ 1.467947] ata2: ata_sff_flush_pio_task: EXIT [ 1.467950] ata2.00: ata_dev_configure: ENTER [ 1.467953] ata2.00: ata_dev_configure: cfg 49:0f00 82:0210 83:5000 84:4000 85:0210 86:1000 87:4000 88:203f [ 1.467956] ata2.00: configured for UDMA/100 [ 1.469335] ata2: ata_sff_flush_pio_task: EXIT [ 1.469359] ata1: ata_sff_flush_pio_task: EXIT [ 1.469651] ata1: ata_sff_flush_pio_task: EXIT [ 1.469654] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7469 86:bc09 87:61e3 88:207f [ 1.469660] ata1.00: ATA-8: ST9250410AS, D005SDM1, max UDMA/133 [ 1.469662] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 1.469997] ata1: ata_sff_flush_pio_task: EXIT [ 1.469999] ata1.00: ata_dev_read_id: ENTER [ 1.552679] md: raid4 personality registered for level 4 [ 1.552681] ata1: ata_sff_flush_pio_task: EXIT [ 1.552684] ata1.00: ata_dev_configure: ENTER [ 1.552686] ata1.00: ata_acpi_push_id: ix = 0, port#: 0 [ 1.552732] ata1.00: ata_dev_get_GTF: ENTER: port#: 0 [ 1.552739] ata1.00: ata_dev_get_GTF: returning gtf=ffff880076f9df18, gtf_count=1 [ 1.553001] ata1: ata_sff_flush_pio_task: EXIT [ 1.553013] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04) [ 1.553385] ata1: ata_sff_flush_pio_task: EXIT [ 1.553387] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7469 86:bc09 87:61e3 88:407f [ 1.553392] ata1.00: configured for UDMA/133 [ 1.553494] scsi 0:0:0:0: Direct-Access ATA ST9250410AS D005 PQ: 0 ANSI: 5 [ 1.553670] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB) [ 1.553704] sd 0:0:0:0: [sda] Write Protect is off [ 1.553706] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.553720] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.571878] scsi 1:0:0:0: CD-ROM PLDS DVD+-RW DS-8A5SH XD12 PQ: 0 ANSI: 5 [ 1.575277] ata2: ata_sff_flush_pio_task: EXIT [ 1.575985] ata2: ata_sff_flush_pio_task: EXIT [ 1.584445] sr0: scsi3-mmc drive: 24x/8x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.584448] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 1.584589] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 1.643412] md: multipath personality registered for level -4 [ 1.653621] device-mapper: uevent: version 1.0.3 [ 1.661420] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 > [ 1.674220] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com [ 1.674471] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.696500] cpuidle: using governor ladder [ 1.708564] cpuidle: using governor menu [ 1.720826] usbcore: registered new interface driver usbhid [ 1.732265] usbhid: USB HID core driver [ 1.743460] ALSA device list: [ 1.754369] No soundcards found. [ 1.765461] TCP cubic registered [ 1.776345] Initializing XFRM netlink socket [ 1.787232] NET: Registered protocol family 17 [ 1.798145] Registering the dns_resolver key type [ 1.810526] registered taskstats version 1 [ 1.821310] rtc_cmos 00:03: setting system clock to 2011-05-16 22:07:47 UTC (1305583667) [ 1.832199] Freeing unused kernel memory: 476k freed [ 1.934844] Refined TSC clocksource calibration: 2393.999 MHz. [ 1.946315] Switching to clocksource tsc [ 2.959756] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null) [ 5.030742] udev[1138]: starting version 165 [ 5.702052] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.707122] wmi: Mapper loaded [ 5.727458] ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 5.740395] ehci_hcd 0000:00:1a.0: setting latency timer to 64 [ 5.740400] ehci_hcd 0000:00:1a.0: EHCI Host Controller [ 5.753231] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 [ 5.769120] ehci_hcd 0000:00:1a.0: debug port 2 [ 5.785756] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported [ 5.785774] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xfbc08000 [ 5.808068] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00 [ 5.820446] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 5.832783] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.845076] usb usb1: Product: EHCI Host Controller [ 5.857204] usb usb1: Manufacturer: Linux 2.6.39-rc7-t2-dbg-00182-g56f8dd5-dirty ehci_hcd [ 5.866976] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 5.867050] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 5.869865] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 5.869890] r8169 0000:13:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 5.869938] r8169 0000:13:00.0: setting latency timer to 64 [ 5.869998] r8169 0000:13:00.0: irq 45 for MSI/MSI-X [ 5.870118] r8169 0000:13:00.0: eth0: RTL8168d/8111d at 0xffffc9000007a000, f0:4d:a2:a1:bd:e9, XID 083000c0 IRQ 45 [ 5.929988] usb usb1: SerialNumber: 0000:00:1a.0 [ 5.941526] thermal LNXTHERM:00: registered as thermal_zone0 [ 5.941528] ACPI: Thermal Zone [THM] (50 C) [ 5.977157] hub 1-0:1.0: USB hub found [ 5.977946] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 6.000927] hub 1-0:1.0: 2 ports detected [ 6.013239] ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 6.026278] ehci_hcd 0000:00:1d.0: setting latency timer to 64 [ 6.026284] ehci_hcd 0000:00:1d.0: EHCI Host Controller [ 6.027167] ata2: ata_sff_flush_pio_task: EXIT [ 6.027876] ata2: ata_sff_flush_pio_task: EXIT [ 6.029273] ata2: ata_sff_flush_pio_task: EXIT [ 6.029978] ata2: ata_sff_flush_pio_task: EXIT [ 6.031388] ata2: ata_sff_flush_pio_task: EXIT [ 6.032102] ata2: ata_sff_flush_pio_task: EXIT [ 6.039706] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 6.040824] input: Dell WMI hotkeys as /devices/virtual/input/input5 [ 6.049864] ata2: ata_sff_flush_pio_task: EXIT [ 6.055829] ata2: ata_sff_flush_pio_task: EXIT [ 6.064604] ata2: ata_sff_flush_pio_task: EXIT [ 6.066712] ata2: ata_sff_flush_pio_task: EXIT [ 6.071128] ata2: ata_sff_flush_pio_task: EXIT [ 6.071717] ehci_hcd 0000:00:1d.0: debug port 2 [ 6.074027] ata2: ata_sff_flush_pio_task: EXIT [ 6.088297] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported [ 6.088322] ehci_hcd 0000:00:1d.0: irq 23, io mem 0xfbc07000 [ 6.110547] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00 [ 6.123304] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 6.136402] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.149438] usb usb2: Product: EHCI Host Controller [ 6.162234] usb usb2: Manufacturer: Linux 2.6.39-rc7-t2-dbg-00182-g56f8dd5-dirty ehci_hcd [ 6.175194] usb usb2: SerialNumber: 0000:00:1d.0 [ 6.187644] hub 2-0:1.0: USB hub found [ 6.199912] hub 2-0:1.0: 2 ports detected [ 6.212055] intel ips 0000:00:1f.6: CPU TDP doesn't match expected value (found 25, expected 29) [ 6.224216] intel ips 0000:00:1f.6: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 6.236603] intel ips 0000:00:1f.6: failed to get i915 symbols, graphics turbo disabled [ 6.248985] intel ips 0000:00:1f.6: IPS driver initialized, MCP temp limit 90 [ 6.261206] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 6.273529] agpgart-intel 0000:00:00.0: Intel HD Graphics Chipset [ 6.285852] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable [ 6.298979] agpgart-intel 0000:00:00.0: detected 32768K stolen memory [ 6.311143] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000 [ 6.323289] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 6.335502] HDA Intel 0000:00:1b.0: irq 46 for MSI/MSI-X [ 6.335535] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 6.336130] usb 1-1: new high speed USB device number 2 using ehci_hcd [ 6.355968] [drm] Initialized drm 1.1.0 20060810 [ 6.438629] input: HDA Intel Mic at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6 [ 6.451605] input: HDA Intel HP Out at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 [ 6.476406] usb 1-1: New USB device found, idVendor=8087, idProduct=0020 [ 6.488559] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 6.500911] hub 1-1:1.0: USB hub found [ 6.513070] hub 1-1:1.0: 6 ports detected [ 6.518598] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 6.518605] i915 0000:00:02.0: setting latency timer to 64 [ 6.566732] i915 0000:00:02.0: irq 47 for MSI/MSI-X [ 6.566737] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 6.567858] [drm] Driver supports precise vblank timestamp query. [ 6.639622] usb 2-1: new high speed USB device number 2 using ehci_hcd [ 6.687907] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 6.755677] usb 2-1: New USB device found, idVendor=8087, idProduct=0020 [ 6.756804] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 6.758152] hub 2-1:1.0: USB hub found [ 6.759270] hub 2-1:1.0: 8 ports detected [ 6.806518] checking generic (c0000000 1ff0000) vs hw (c0000000 10000000) [ 6.806521] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver [ 6.807616] Console: switching to colour dummy device 80x25 [ 6.807945] fbcon: inteldrmfb (fb0) is primary device [ 6.965814] Console: switching to colour frame buffer device 170x48 [ 6.968450] fb0: inteldrmfb frame buffer device [ 6.968472] drm: registered panic notifier [ 6.969334] acpi device:2b: registered as cooling_device4 [ 6.969531] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input8 [ 6.969603] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 6.969874] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 7.035123] usb 2-1.1: new low speed USB device number 3 using ehci_hcd [ 7.114311] usb 2-1.1: New USB device found, idVendor=093a, idProduct=2510 [ 7.114392] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 7.114458] usb 2-1.1: Product: USB OPTICAL MOUSE [ 7.114482] usb 2-1.1: Manufacturer: PIXART [ 7.118874] input: PIXART USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/input/input9 [ 7.118995] generic-usb 0003:093A:2510.0001: input,hidraw0: USB HID v1.11 Mouse [PIXART USB OPTICAL MOUSE] on usb-0000:00:1d.0-1.1/input0 [ 7.191809] usb 2-1.8: new high speed USB device number 4 using ehci_hcd [ 7.234556] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 7.314908] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input10 [ 7.355275] usb 2-1.8: New USB device found, idVendor=0c45, idProduct=6421 [ 7.355370] usb 2-1.8: New USB device strings: Mfr=2, Product=1, SerialNumber=0 [ 7.355447] usb 2-1.8: Product: Laptop_Integrated_Webcam_2M [ 7.355473] usb 2-1.8: Manufacturer: CN023VXT7248706813AE [ 7.486370] Linux video capture interface: v2.00 [ 7.491178] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:6421) [ 7.499756] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.8/2-1.8:1.0/input/input11 [ 7.501228] usbcore: registered new interface driver uvcvideo [ 7.502610] USB Video Class driver (v1.0.0) [ 9.194232] Adding 9703224k swap on /dev/sda8. Priority:-1 extents:1 across:9703224k [ 9.350263] fuse init (API version 7.16) [ 10.309013] EXT4-fs (sda5): re-mounted. Opts: (null) [ 10.375757] EXT4-fs (sda5): re-mounted. Opts: (null) [ 11.442683] intel ips 0000:00:1f.6: i915 driver attached, reenabling gpu turbo [ 14.697490] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 18.753992] NET: Registered protocol family 10 [ 29.059615] ata2: ata_sff_flush_pio_task: EXIT [ 29.060375] ata2: ata_sff_flush_pio_task: EXIT [ 29.075263] ata2: ata_sff_flush_pio_task: EXIT [ 29.075982] ata2: ata_sff_flush_pio_task: EXIT [ 29.077373] ata2: ata_sff_flush_pio_task: EXIT [ 29.078117] ata2: ata_sff_flush_pio_task: EXIT [ 39.162771] r8169 0000:13:00.0: eth0: unable to load firmware patch rtl_nic/rtl8168d-2.fw (-2) [ 39.170122] r8169 0000:13:00.0: eth0: link down [ 39.170127] r8169 0000:13:00.0: eth0: link down [ 39.170326] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 40.833649] r8169 0000:13:00.0: eth0: link up [ 40.833871] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 41.315319] r8169 0000:13:00.0: eth0: link down [ 41.315325] r8169 0000:13:00.0: eth0: link down [ 41.315514] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 41.344866] r8169 0000:13:00.0: eth0: link down [ 41.345058] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 42.872200] r8169 0000:13:00.0: eth0: link up [ 42.872454] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 44.110016] ata2: ata_sff_flush_pio_task: EXIT [ 44.110809] ata2: ata_sff_flush_pio_task: EXIT [ 44.112575] ata2: ata_sff_flush_pio_task: EXIT [ 44.113352] ata2: ata_sff_flush_pio_task: EXIT [ 44.122044] ata2: ata_sff_flush_pio_task: EXIT [ 44.122805] ata2: ata_sff_flush_pio_task: EXIT [ 44.125329] ata2: ata_sff_flush_pio_task: EXIT [ 44.126063] ata2: ata_sff_flush_pio_task: EXIT [ 44.136354] ata2: ata_sff_flush_pio_task: EXIT [ 44.137154] ata2: ata_sff_flush_pio_task: EXIT [ 44.138512] ata2: ata_sff_flush_pio_task: EXIT [ 44.139245] ata2: ata_sff_flush_pio_task: EXIT [ 46.105770] ata2: ata_sff_flush_pio_task: EXIT [ 46.106541] ata2: ata_sff_flush_pio_task: EXIT [ 46.108279] ata2: ata_sff_flush_pio_task: EXIT [ 46.109015] ata2: ata_sff_flush_pio_task: EXIT [ 48.103854] ata2: ata_sff_flush_pio_task: EXIT [ 48.104601] ata2: ata_sff_flush_pio_task: EXIT [ 48.105967] ata2: ata_sff_flush_pio_task: EXIT [ 48.106707] ata2: ata_sff_flush_pio_task: EXIT [ 50.098425] ata2: ata_sff_flush_pio_task: EXIT [ 50.099177] ata2: ata_sff_flush_pio_task: EXIT [ 50.100541] ata2: ata_sff_flush_pio_task: EXIT [ 50.101275] ata2: ata_sff_flush_pio_task: EXIT [ 51.108191] ata1: ata_sff_flush_pio_task: EXIT [ 51.108213] ata1.00: ata_dev_read_id: ENTER [ 51.109582] ata1: ata_sff_flush_pio_task: EXIT [ 51.109589] ata1.00: ata_dev_configure: ENTER [ 51.109958] ata1: ata_sff_flush_pio_task: EXIT [ 51.109964] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7469 86:bc09 87:61e3 88:407f [ 51.110271] ata1: ata_sff_flush_pio_task: EXIT [ 51.110275] ata1.00: ata_dev_read_id: ENTER [ 51.111664] ata1: ata_sff_flush_pio_task: EXIT [ 51.111669] ata1.00: ata_dev_configure: ENTER [ 51.111999] ata1: ata_sff_flush_pio_task: EXIT [ 51.112003] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7469 86:bc09 87:61e3 88:407f [ 51.112009] ata1.00: configured for UDMA/133 [ 51.112013] ata1: EH complete [ 51.513508] EXT4-fs (sda5): re-mounted. Opts: commit=0 [ 51.938165] EXT4-fs (sda6): re-mounted. Opts: commit=0 [ 52.094554] ata2: ata_sff_flush_pio_task: EXIT [ 52.095273] ata2: ata_sff_flush_pio_task: EXIT ata_sff_flush_pio_task ... // AC unplugged here [ 169.892680] ata2: ata_sff_flush_pio_task: EXIT [ 169.894446] ata2: ata_sff_flush_pio_task: EXIT [ 169.895236] ata2: ata_sff_flush_pio_task: EXIT [ 170.890864] ata2: ata_sff_flush_pio_task: EXIT [ 170.891605] ata2: ata_sff_flush_pio_task: EXIT [ 171.331273] ata1: ata_sff_flush_pio_task: EXIT [ 171.331299] ata1.00: ata_dev_read_id: ENTER [ 171.332654] ata1: ata_sff_flush_pio_task: EXIT [ 171.332663] ata1.00: ata_dev_configure: ENTER [ 171.333013] ata1: ata_sff_flush_pio_task: EXIT [ 171.333023] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7449 86:be09 87:61e3 88:407f [ 171.333371] ata1: ata_sff_flush_pio_task: EXIT [ 171.333376] ata1.00: ata_dev_read_id: ENTER [ 171.334769] ata1: ata_sff_flush_pio_task: EXIT [ 171.334773] ata1.00: ata_dev_configure: ENTER [ 171.335119] ata1: ata_sff_flush_pio_task: EXIT [ 171.335122] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7449 86:be09 87:61e3 88:407f [ 171.335128] ata1.00: configured for UDMA/133 [ 171.335131] ata1: EH complete [ 171.335252] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 171.552842] EXT4-fs (sda5): re-mounted. Opts: commit=600 [ 171.556019] EXT4-fs (sda6): re-mounted. Opts: commit=600 ata_sff_flush_pio_task ... // AC plugged in here [ 194.852806] ata2: ata_sff_flush_pio_task: EXIT [ 195.849754] ata2: ata_sff_flush_pio_task: EXIT [ 195.850684] ata2: ata_sff_flush_pio_task: EXIT [ 195.852709] ata2: ata_sff_flush_pio_task: EXIT [ 195.853603] ata2: ata_sff_flush_pio_task: EXIT [ 196.657169] ata1: ata_sff_flush_pio_task: EXIT [ 196.657198] ata1: hard resetting link [ 196.847316] ata2: ata_sff_flush_pio_task: EXIT [ 196.848142] ata2: ata_sff_flush_pio_task: EXIT [ 196.961568] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 196.961581] ata1.00: ata_dev_read_id: ENTER [ 196.962954] ata1: ata_sff_flush_pio_task: EXIT [ 196.962964] ata1.00: ata_dev_configure: ENTER [ 196.962973] ata1.00: ata_acpi_push_id: ix = 0, port#: 0 [ 196.963112] ata1.00: ata_dev_get_GTF: ENTER: port#: 0 [ 196.963123] ata1.00: ata_dev_get_GTF: returning gtf=ffff88003f0f31f8, gtf_count=1 [ 196.963435] ata1: ata_sff_flush_pio_task: EXIT [ 196.963478] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04) [ 196.963799] ata1: ata_sff_flush_pio_task: EXIT [ 196.963807] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7469 86:bc09 87:61e3 88:407f [ 196.964203] ata1: ata_sff_flush_pio_task: EXIT [ 196.964209] ata1.00: ata_dev_read_id: ENTER [ 196.965645] ata1: ata_sff_flush_pio_task: EXIT [ 196.965654] ata1.00: ata_dev_configure: ENTER [ 196.965661] ata1.00: ata_acpi_push_id: ix = 0, port#: 0 [ 196.965788] ata1.00: ata_dev_get_GTF: ENTER: port#: 0 [ 196.965796] ata1.00: ata_dev_get_GTF: returning gtf=ffff88003f0f3218, gtf_count=1 [ 196.966163] ata1: ata_sff_flush_pio_task: EXIT [ 196.966181] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04) [ 196.966528] ata1: ata_sff_flush_pio_task: EXIT [ 196.966536] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7469 86:bc09 87:61e3 88:407f [ 196.966549] ata1.00: configured for UDMA/133 [ 196.968832] ata1: ata_sff_flush_pio_task: EXIT [ 196.968852] ata1: EH complete [ 196.969193] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 197.844944] ata2: ata_sff_flush_pio_task: EXIT [ 197.845668] ata2: ata_sff_flush_pio_task: EXIT [ 197.847465] ata2: ata_sff_flush_pio_task: EXIT [ 197.848206] ata2: ata_sff_flush_pio_task: EXIT [ 198.842544] ata2: ata_sff_flush_pio_task: EXIT [ 198.843262] ata2: ata_sff_flush_pio_task: EXIT [ 199.841101] ata2: ata_sff_flush_pio_task: EXIT [ 199.841828] ata2: ata_sff_flush_pio_task: EXIT [ 199.843997] ata2: ata_sff_flush_pio_task: EXIT [ 199.844813] ata2: ata_sff_flush_pio_task: EXIT [ 200.839640] ata2: ata_sff_flush_pio_task: EXIT [ 200.840376] ata2: ata_sff_flush_pio_task: EXIT [ 201.837089] ata2: ata_sff_flush_pio_task: EXIT [ 201.837829] ata2: ata_sff_flush_pio_task: EXIT [ 201.840041] ata2: ata_sff_flush_pio_task: EXIT [ 201.840799] ata2: ata_sff_flush_pio_task: EXIT [ 202.836319] ata2: ata_sff_flush_pio_task: EXIT [ 202.837052] ata2: ata_sff_flush_pio_task: EXIT [ 203.834148] ata2: ata_sff_flush_pio_task: EXIT [ 203.834979] ata2: ata_sff_flush_pio_task: EXIT [ 203.837061] ata2: ata_sff_flush_pio_task: EXIT [ 203.837841] ata2: ata_sff_flush_pio_task: EXIT [ 204.832894] ata2: ata_sff_flush_pio_task: EXIT [ 204.833738] ata2: ata_sff_flush_pio_task: EXIT [ 205.831179] ata2: ata_sff_flush_pio_task: EXIT [ 205.831996] ata2: ata_sff_flush_pio_task: EXIT [ 205.834077] ata2: ata_sff_flush_pio_task: EXIT [ 205.834876] ata2: ata_sff_flush_pio_task: EXIT [ 206.829767] ata2: ata_sff_flush_pio_task: EXIT [ 206.830569] ata2: ata_sff_flush_pio_task: EXIT [ 207.827329] ata2: ata_sff_flush_pio_task: EXIT [ 207.828071] ata2: ata_sff_flush_pio_task: EXIT [ 207.830245] ata2: ata_sff_flush_pio_task: EXIT [ 207.830980] ata2: ata_sff_flush_pio_task: EXIT [ 208.825369] ata2: ata_sff_flush_pio_task: EXIT [ 208.826251] ata2: ata_sff_flush_pio_task: EXIT [ 209.823939] ata2: ata_sff_flush_pio_task: EXIT [ 209.824742] ata2: ata_sff_flush_pio_task: EXIT [ 209.826890] ata2: ata_sff_flush_pio_task: EXIT [ 209.827708] ata2: ata_sff_flush_pio_task: EXIT [ 210.822077] ata2: ata_sff_flush_pio_task: EXIT [ 210.822877] ata2: ata_sff_flush_pio_task: EXIT [ 211.820218] ata2: ata_sff_flush_pio_task: EXIT [ 211.821068] ata2: ata_sff_flush_pio_task: EXIT [ 211.823162] ata2: ata_sff_flush_pio_task: EXIT [ 211.824145] ata2: ata_sff_flush_pio_task: EXIT [ 212.515778] ata1: ata_sff_flush_pio_task: EXIT [ 212.515791] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x50000 action 0x6 frozen [ 212.515796] ata1: SError: { PHYRdyChg CommWake } [ 212.515800] ata1.00: failed command: IDLE [ 212.515807] ata1.00: cmd e3/00:00:00:00:00/00:00:00:00:00/40 tag 0 [ 212.515808] res 40/00:00:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout) [ 212.515812] ata1.00: status: { DRDY } [ 212.515817] ata1: hard resetting link [ 212.818588] ata2: ata_sff_flush_pio_task: EXIT [ 212.819328] ata2: ata_sff_flush_pio_task: EXIT [ 212.820169] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 212.820178] ata1.00: ata_dev_read_id: ENTER [ 212.821542] ata1: ata_sff_flush_pio_task: EXIT [ 212.821547] ata1.00: ata_dev_configure: ENTER [ 212.821552] ata1.00: ata_acpi_push_id: ix = 0, port#: 0 [ 212.821640] ata1.00: ata_dev_get_GTF: ENTER: port#: 0 [ 212.821652] ata1.00: ata_dev_get_GTF: returning gtf=ffff880042983038, gtf_count=1 [ 212.822005] ata1: ata_sff_flush_pio_task: EXIT [ 212.822022] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04) [ 212.822358] ata1: ata_sff_flush_pio_task: EXIT [ 212.822363] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7469 86:bc09 87:61e3 88:407f [ 212.822721] ata1: ata_sff_flush_pio_task: EXIT [ 212.822727] ata1.00: ata_dev_read_id: ENTER [ 212.824130] ata1: ata_sff_flush_pio_task: EXIT [ 212.824139] ata1.00: ata_dev_configure: ENTER [ 212.824146] ata1.00: ata_acpi_push_id: ix = 0, port#: 0 [ 212.824271] ata1.00: ata_dev_get_GTF: ENTER: port#: 0 [ 212.824280] ata1.00: ata_dev_get_GTF: returning gtf=ffff880042b5a5f8, gtf_count=1 [ 212.824613] ata1: ata_sff_flush_pio_task: EXIT [ 212.824630] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04) [ 212.824977] ata1: ata_sff_flush_pio_task: EXIT [ 212.824985] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7469 86:bc09 87:61e3 88:407f [ 212.824997] ata1.00: configured for UDMA/133 [ 212.827204] ata1: ata_sff_flush_pio_task: EXIT [ 212.827244] ata1: EH complete [ 213.816583] ata2: ata_sff_flush_pio_task: EXIT [ 213.817430] ata2: ata_sff_flush_pio_task: EXIT [ 213.819507] ata2: ata_sff_flush_pio_task: EXIT [ 213.820313] ata2: ata_sff_flush_pio_task: EXIT [ 214.815302] ata2: ata_sff_flush_pio_task: EXIT [ 214.816140] ata2: ata_sff_flush_pio_task: EXIT [ 215.814016] ata2: ata_sff_flush_pio_task: EXIT [ 215.814848] ata2: ata_sff_flush_pio_task: EXIT [ 215.817183] ata2: ata_sff_flush_pio_task: EXIT [ 215.817986] ata2: ata_sff_flush_pio_task: EXIT [ 216.811871] ata2: ata_sff_flush_pio_task: EXIT [ 216.812676] ata2: ata_sff_flush_pio_task: EXIT [ 217.810170] ata2: ata_sff_flush_pio_task: EXIT [ 217.810901] ata2: ata_sff_flush_pio_task: EXIT [ 217.812972] ata2: ata_sff_flush_pio_task: EXIT [ 217.813716] ata2: ata_sff_flush_pio_task: EXIT [ 218.808633] ata2: ata_sff_flush_pio_task: EXIT [ 218.809406] ata2: ata_sff_flush_pio_task: EXIT [ 219.806652] ata2: ata_sff_flush_pio_task: EXIT [ 219.807450] ata2: ata_sff_flush_pio_task: EXIT [ 219.809866] ata2: ata_sff_flush_pio_task: EXIT [ 219.810671] ata2: ata_sff_flush_pio_task: EXIT [ 220.804536] ata2: ata_sff_flush_pio_task: EXIT [ 220.805386] ata2: ata_sff_flush_pio_task: EXIT [ 221.802961] ata2: ata_sff_flush_pio_task: EXIT [ 221.803798] ata2: ata_sff_flush_pio_task: EXIT [ 221.806129] ata2: ata_sff_flush_pio_task: EXIT [ 221.806934] ata2: ata_sff_flush_pio_task: EXIT [ 222.801320] ata2: ata_sff_flush_pio_task: EXIT [ 222.802277] ata2: ata_sff_flush_pio_task: EXIT [ 223.800549] ata2: ata_sff_flush_pio_task: EXIT [ 223.801420] ata2: ata_sff_flush_pio_task: EXIT [ 223.803516] ata2: ata_sff_flush_pio_task: EXIT [ 223.804322] ata2: ata_sff_flush_pio_task: EXIT [ 224.797938] ata2: ata_sff_flush_pio_task: EXIT [ 224.798704] ata2: ata_sff_flush_pio_task: EXIT [ 225.796862] ata2: ata_sff_flush_pio_task: EXIT [ 225.797694] ata2: ata_sff_flush_pio_task: EXIT [ 225.799780] ata2: ata_sff_flush_pio_task: EXIT [ 225.800570] ata2: ata_sff_flush_pio_task: EXIT [ 226.795121] ata2: ata_sff_flush_pio_task: EXIT [ 226.795957] ata2: ata_sff_flush_pio_task: EXIT [ 227.793051] ata2: ata_sff_flush_pio_task: EXIT [ 227.793798] ata2: ata_sff_flush_pio_task: EXIT [ 227.795975] ata2: ata_sff_flush_pio_task: EXIT [ 227.796720] ata2: ata_sff_flush_pio_task: EXIT [ 228.791962] ata2: ata_sff_flush_pio_task: EXIT [ 228.792807] ata2: ata_sff_flush_pio_task: EXIT [ 229.789349] ata2: ata_sff_flush_pio_task: EXIT [ 229.790169] ata2: ata_sff_flush_pio_task: EXIT [ 229.792261] ata2: ata_sff_flush_pio_task: EXIT [ 229.793098] ata2: ata_sff_flush_pio_task: EXIT [ 230.787892] ata2: ata_sff_flush_pio_task: EXIT [ 230.788654] ata2: ata_sff_flush_pio_task: EXIT [ 231.786653] ata2: ata_sff_flush_pio_task: EXIT [ 231.787421] ata2: ata_sff_flush_pio_task: EXIT [ 231.789566] ata2: ata_sff_flush_pio_task: EXIT [ 231.790298] ata2: ata_sff_flush_pio_task: EXIT [ 232.784851] ata2: ata_sff_flush_pio_task: EXIT [ 232.785619] ata2: ata_sff_flush_pio_task: EXIT [ 233.782584] ata2: ata_sff_flush_pio_task: EXIT [ 233.783426] ata2: ata_sff_flush_pio_task: EXIT [ 233.785581] ata2: ata_sff_flush_pio_task: EXIT [ 233.786437] ata2: ata_sff_flush_pio_task: EXIT [ 234.780791] ata2: ata_sff_flush_pio_task: EXIT [ 234.781569] ata2: ata_sff_flush_pio_task: EXIT [ 235.782556] ata2: ata_sff_flush_pio_task: EXIT [ 235.783404] ata2: ata_sff_flush_pio_task: EXIT [ 235.785463] ata2: ata_sff_flush_pio_task: EXIT [ 235.786218] ata2: ata_sff_flush_pio_task: EXIT [ 236.780273] ata2: ata_sff_flush_pio_task: EXIT [ 236.781086] ata2: ata_sff_flush_pio_task: EXIT [ 237.777845] ata2: ata_sff_flush_pio_task: EXIT [ 237.778576] ata2: ata_sff_flush_pio_task: EXIT [ 237.780824] ata2: ata_sff_flush_pio_task: EXIT [ 237.781629] ata2: ata_sff_flush_pio_task: EXIT [ 238.775639] ata2: ata_sff_flush_pio_task: EXIT [ 238.776473] ata2: ata_sff_flush_pio_task: EXIT [ 239.773247] ata2: ata_sff_flush_pio_task: EXIT [ 239.774044] ata2: ata_sff_flush_pio_task: EXIT [ 239.776245] ata2: ata_sff_flush_pio_task: EXIT [ 239.777088] ata2: ata_sff_flush_pio_task: EXIT [ 240.770892] ata2: ata_sff_flush_pio_task: EXIT [ 240.771702] ata2: ata_sff_flush_pio_task: EXIT [ 241.768516] ata2: ata_sff_flush_pio_task: EXIT [ 241.769329] ata2: ata_sff_flush_pio_task: EXIT [ 241.771431] ata2: ata_sff_flush_pio_task: EXIT [ 241.772250] ata2: ata_sff_flush_pio_task: EXIT [ 242.767517] ata2: ata_sff_flush_pio_task: EXIT [ 242.768266] ata2: ata_sff_flush_pio_task: EXIT [ 243.502391] ata1: ata_sff_flush_pio_task: EXIT [ 243.502405] ata1.00: exception Emask 0x0 SAct 0xff SErr 0x50000 action 0x6 frozen [ 243.502410] ata1: SError: { PHYRdyChg CommWake } [ 243.502415] ata1.00: failed command: WRITE FPDMA QUEUED [ 243.502423] ata1.00: cmd 61/08:00:2b:00:02/00:00:08:00:00/40 tag 0 ncq 4096 out [ 243.502424] res 40/00:00:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout) [ 243.502428] ata1.00: status: { DRDY } [ 243.502431] ata1.00: failed command: WRITE FPDMA QUEUED [ 243.502438] ata1.00: cmd 61/08:08:2b:25:9a/00:00:09:00:00/40 tag 1 ncq 4096 out [ 243.502439] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 243.502443] ata1.00: status: { DRDY } [ 243.502445] ata1.00: failed command: WRITE FPDMA QUEUED [ 243.502452] ata1.00: cmd 61/08:10:e3:94:b7/00:00:09:00:00/40 tag 2 ncq 4096 out [ 243.502454] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 243.502457] ata1.00: status: { DRDY } [ 243.502460] ata1.00: failed command: WRITE FPDMA QUEUED [ 243.502466] ata1.00: cmd 61/08:18:f3:94:b7/00:00:09:00:00/40 tag 3 ncq 4096 out [ 243.502468] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 243.502471] ata1.00: status: { DRDY } [ 243.502474] ata1.00: failed command: WRITE FPDMA QUEUED [ 243.502481] ata1.00: cmd 61/08:20:03:98:b7/00:00:09:00:00/40 tag 4 ncq 4096 out [ 243.502482] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 243.502485] ata1.00: status: { DRDY } [ 243.502491] ata1.00: failed command: WRITE FPDMA QUEUED [ 243.502495] ata1.00: cmd 61/08:28:5b:9f:b7/00:00:09:00:00/40 tag 5 ncq 4096 out [ 243.502496] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 243.502498] ata1.00: status: { DRDY } [ 243.502500] ata1.00: failed command: WRITE FPDMA QUEUED [ 243.502504] ata1.00: cmd 61/10:30:1a:88:3b/00:00:0d:00:00/40 tag 6 ncq 8192 out [ 243.502505] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 243.502507] ata1.00: status: { DRDY } [ 243.502508] ata1.00: failed command: WRITE FPDMA QUEUED [ 243.502512] ata1.00: cmd 61/10:38:db:30:aa/00:00:08:00:00/40 tag 7 ncq 8192 out [ 243.502513] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 243.502515] ata1.00: status: { DRDY } [ 243.502520] ata1: hard resetting link [ 243.764963] ata2: ata_sff_flush_pio_task: EXIT [ 243.765777] ata2: ata_sff_flush_pio_task: EXIT [ 243.767916] ata2: ata_sff_flush_pio_task: EXIT [ 243.768724] ata2: ata_sff_flush_pio_task: EXIT [ 243.806778] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 243.806788] ata1.00: ata_dev_read_id: ENTER [ 243.871154] ata1: ata_sff_flush_pio_task: EXIT [ 243.871324] ata1: ata_sff_flush_pio_task: EXIT [ 243.871339] ata1.00: both IDENTIFYs aborted, assuming NODEV [ 243.871345] ata1.00: revalidation failed (errno=-2) [ 244.764262] ata2: ata_sff_flush_pio_task: EXIT [ 248.798169] ata1: hard resetting link [ 249.102651] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 249.102663] ata1.00: ata_dev_read_id: ENTER [ 249.104098] ata1: ata_sff_flush_pio_task: EXIT [ 249.104107] ata1.00: ata_dev_configure: ENTER [ 249.104117] ata1.00: ata_acpi_push_id: ix = 0, port#: 0 [ 249.104256] ata1.00: ata_dev_get_GTF: ENTER: port#: 0 [ 249.104267] ata1.00: ata_dev_get_GTF: returning gtf=ffff880042983458, gtf_count=1 [ 249.104629] ata1: ata_sff_flush_pio_task: EXIT [ 249.104648] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04) [ 249.105072] ata1: ata_sff_flush_pio_task: EXIT [ 249.105080] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7469 86:bc09 87:61e3 88:407f [ 249.105450] ata1: ata_sff_flush_pio_task: EXIT [ 249.105457] ata1.00: ata_dev_read_id: ENTER [ 249.106874] ata1: ata_sff_flush_pio_task: EXIT [ 249.106882] ata1.00: ata_dev_configure: ENTER [ 249.106890] ata1.00: ata_acpi_push_id: ix = 0, port#: 0 [ 249.107012] ata1.00: ata_dev_get_GTF: ENTER: port#: 0 [ 249.107020] ata1.00: ata_dev_get_GTF: returning gtf=ffff880042983018, gtf_count=1 [ 249.107381] ata1: ata_sff_flush_pio_task: EXIT [ 249.107399] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04) [ 249.107783] ata1: ata_sff_flush_pio_task: EXIT [ 249.107787] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7469 86:bc09 87:61e3 88:407f [ 249.107793] ata1.00: configured for UDMA/133 [ 249.110017] ata1: ata_sff_flush_pio_task: EXIT [ 249.110024] ata1.00: device reported invalid CHS sector 0 [ 249.110028] ata1.00: device reported invalid CHS sector 0 [ 249.110031] ata1.00: device reported invalid CHS sector 0 [ 249.110034] ata1.00: device reported invalid CHS sector 0 [ 249.110036] ata1.00: device reported invalid CHS sector 0 [ 249.110039] ata1.00: device reported invalid CHS sector 0 [ 249.110042] ata1.00: device reported invalid CHS sector 0 [ 249.110044] ata1.00: device reported invalid CHS sector 0 [ 249.110070] ata1: EH complete [ 253.789605] ata2: ata_sff_flush_pio_task: EXIT [ 253.789614] ata2.00: qc timeout (cmd 0xa0) [ 253.789627] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x50000 action 0x6 frozen [ 253.789630] ata2.00: irq_stat 0x40000001 [ 253.789634] ata2: SError: { PHYRdyChg CommWake } [ 253.789639] sr 1:0:0:0: CDB: cdb[0]=0x0: 00 00 00 00 00 00 [ 253.789652] ata2.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 [ 253.789653] res 51/20:03:00:00:00/00:00:00:00:00/a0 Emask 0x5 (timeout) [ 253.789657] ata2.00: status: { DRDY ERR } [ 253.789664] ata2: hard resetting link [ 254.094046] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 254.094057] ata2.00: ata_dev_read_id: ENTER [ 254.096842] ata2: ata_sff_flush_pio_task: EXIT [ 254.096849] ata2.00: ata_dev_configure: ENTER [ 254.096856] ata2.00: ata_dev_configure: cfg 49:0f00 82:0210 83:5000 84:4000 85:0210 86:1000 87:4000 88:203f [ 254.097730] ata2: ata_sff_flush_pio_task: EXIT [ 254.097737] ata2.00: ata_dev_read_id: ENTER [ 254.098185] ata2: ata_sff_flush_pio_task: EXIT [ 254.098190] ata2.00: ata_dev_configure: ENTER [ 254.098194] ata2.00: ata_dev_configure: cfg 49:0f00 82:0210 83:5000 84:4000 85:0210 86:1000 87:4000 88:203f [ 254.098207] ata2.00: configured for UDMA/100 [ 254.099479] ata2: ata_sff_flush_pio_task: EXIT [ 254.100281] ata2: ata_sff_flush_pio_task: EXIT [ 254.100321] ata2: EH complete [ 279.408483] ata1: ata_sff_flush_pio_task: EXIT [ 279.408498] ata1.00: exception Emask 0x0 SAct 0xff SErr 0x50000 action 0x6 frozen [ 279.408503] ata1: SError: { PHYRdyChg CommWake } [ 279.408507] ata1.00: failed command: WRITE FPDMA QUEUED [ 279.408515] ata1.00: cmd 61/10:00:db:30:aa/00:00:08:00:00/40 tag 0 ncq 8192 out [ 279.408517] res 40/00:00:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout) [ 279.408520] ata1.00: status: { DRDY } [ 279.408523] ata1.00: failed command: WRITE FPDMA QUEUED [ 279.408530] ata1.00: cmd 61/10:08:1a:88:3b/00:00:0d:00:00/40 tag 1 ncq 8192 out [ 279.408532] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 279.408535] ata1.00: status: { DRDY } [ 279.408538] ata1.00: failed command: WRITE FPDMA QUEUED [ 279.408544] ata1.00: cmd 61/08:10:5b:9f:b7/00:00:09:00:00/40 tag 2 ncq 4096 out [ 279.408546] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 279.408549] ata1.00: status: { DRDY } [ 279.408552] ata1.00: failed command: WRITE FPDMA QUEUED [ 279.408559] ata1.00: cmd 61/08:18:03:98:b7/00:00:09:00:00/40 tag 3 ncq 4096 out [ 279.408560] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 279.408563] ata1.00: status: { DRDY } [ 279.408566] ata1.00: failed command: WRITE FPDMA QUEUED [ 279.408575] ata1.00: cmd 61/08:20:f3:94:b7/00:00:09:00:00/40 tag 4 ncq 4096 out [ 279.408576] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 279.408578] ata1.00: status: { DRDY } [ 279.408580] ata1.00: failed command: WRITE FPDMA QUEUED [ 279.408584] ata1.00: cmd 61/08:28:e3:94:b7/00:00:09:00:00/40 tag 5 ncq 4096 out [ 279.408585] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 279.408587] ata1.00: status: { DRDY } [ 279.408588] ata1.00: failed command: WRITE FPDMA QUEUED [ 279.408592] ata1.00: cmd 61/08:30:2b:25:9a/00:00:09:00:00/40 tag 6 ncq 4096 out [ 279.408593] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 279.408595] ata1.00: status: { DRDY } [ 279.408597] ata1.00: failed command: WRITE FPDMA QUEUED [ 279.408601] ata1.00: cmd 61/08:38:2b:00:02/00:00:08:00:00/40 tag 7 ncq 4096 out [ 279.408602] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 279.408604] ata1.00: status: { DRDY } [ 279.408609] ata1: hard resetting link [ 279.712882] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 279.712893] ata1.00: ata_dev_read_id: ENTER [ 279.715013] ata1: illegal qc_active transition (80000000->800000e0) [ 279.715030] ata1: ata_sff_flush_pio_task: EXIT [ 279.715045] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x100) [ 279.715048] ata1.00: revalidation failed (errno=-5) [ 284.455724] ata2: ata_sff_flush_pio_task: EXIT [ 284.704301] ata1: hard resetting link [ 284.704331] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 284.704337] sr 1:0:0:0: CDB: cdb[0]=0x0: 00 00 00 00 00 00 [ 284.704350] ata2.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 [ 284.704352] res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout) [ 284.704356] ata2.00: status: { DRDY } [ 284.704361] ata2: hard resetting link [ 285.008768] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 285.008780] ata1.00: ata_dev_read_id: ENTER [ 285.008812] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 285.008820] ata2.00: ata_dev_read_id: ENTER [ 285.010179] ata1: ata_sff_flush_pio_task: EXIT [ 285.010188] ata1.00: ata_dev_configure: ENTER [ 285.010198] ata1.00: ata_acpi_push_id: ix = 0, port#: 0 [ 285.010323] ata1.00: ata_dev_get_GTF: ENTER: port#: 0 [ 285.010334] ata1.00: ata_dev_get_GTF: returning gtf=ffff880042983078, gtf_count=1 [ 285.010687] ata1: ata_sff_flush_pio_task: EXIT [ 285.010707] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04) [ 285.011073] ata1: ata_sff_flush_pio_task: EXIT [ 285.011081] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7469 86:bc09 87:61e3 88:407f [ 285.011168] ata2: ata_sff_flush_pio_task: EXIT [ 285.011177] ata2.00: ata_dev_configure: ENTER [ 285.011187] ata2.00: ata_dev_configure: cfg 49:0f00 82:0210 83:5000 84:4000 85:0210 86:1000 87:4000 88:203f [ 285.011436] ata1: ata_sff_flush_pio_task: EXIT [ 285.011442] ata1.00: ata_dev_read_id: ENTER [ 285.012153] ata2: ata_sff_flush_pio_task: EXIT [ 285.012160] ata2.00: ata_dev_read_id: ENTER [ 285.012535] ata2: ata_sff_flush_pio_task: EXIT [ 285.012542] ata2.00: ata_dev_configure: ENTER [ 285.012551] ata2.00: ata_dev_configure: cfg 49:0f00 82:0210 83:5000 84:4000 85:0210 86:1000 87:4000 88:203f [ 285.012561] ata2.00: configured for UDMA/100 [ 285.012796] ata1: ata_sff_flush_pio_task: EXIT [ 285.012804] ata1.00: ata_dev_configure: ENTER [ 285.012812] ata1.00: ata_acpi_push_id: ix = 0, port#: 0 [ 285.012872] ata1.00: ata_dev_get_GTF: ENTER: port#: 0 [ 285.012885] ata1.00: ata_dev_get_GTF: returning gtf=ffff880042983058, gtf_count=1 [ 285.013186] ata1: ata_sff_flush_pio_task: EXIT [ 285.013202] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04) [ 285.013557] ata1: ata_sff_flush_pio_task: EXIT [ 285.013564] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7469 86:bc09 87:61e3 88:407f [ 285.013577] ata1.00: configured for UDMA/133 [ 285.013890] ata2: ata_sff_flush_pio_task: EXIT [ 285.014658] ata2: ata_sff_flush_pio_task: EXIT [ 285.014694] ata2: EH complete [ 285.015803] ata1: ata_sff_flush_pio_task: EXIT [ 285.015812] ata1.00: device reported invalid CHS sector 0 [ 285.015818] ata1.00: device reported invalid CHS sector 0 [ 285.015822] ata1.00: device reported invalid CHS sector 0 [ 285.015826] ata1.00: device reported invalid CHS sector 0 [ 285.015830] ata1.00: device reported invalid CHS sector 0 [ 285.015834] ata1.00: device reported invalid CHS sector 0 [ 285.015838] ata1.00: device reported invalid CHS sector 0 [ 285.015842] ata1.00: device reported invalid CHS sector 0 [ 285.015872] ata1: EH complete [ 295.380961] ata2: ata_sff_flush_pio_task: EXIT [ 295.380974] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 295.380980] sr 1:0:0:0: CDB: cdb[0]=0x1e: 1e 00 00 00 00 00 [ 295.380993] ata2.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 [ 295.380995] res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout) [ 295.380998] ata2.00: status: { DRDY } [ 295.381005] ata2: hard resetting link [ 295.685326] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 295.685336] ata2.00: ata_dev_read_id: ENTER [ 295.688160] ata2: ata_sff_flush_pio_task: EXIT [ 295.688166] ata2.00: ata_dev_configure: ENTER [ 295.688174] ata2.00: ata_dev_configure: cfg 49:0f00 82:0210 83:5000 84:4000 85:0210 86:1000 87:4000 88:203f [ 295.689277] ata2: ata_sff_flush_pio_task: EXIT [ 295.689284] ata2.00: ata_dev_read_id: ENTER [ 295.689697] ata2: ata_sff_flush_pio_task: EXIT [ 295.689706] ata2.00: ata_dev_configure: ENTER [ 295.689717] ata2.00: ata_dev_configure: cfg 49:0f00 82:0210 83:5000 84:4000 85:0210 86:1000 87:4000 88:203f [ 295.689726] ata2.00: configured for UDMA/100 [ 295.691000] ata2: ata_sff_flush_pio_task: EXIT [ 295.691768] ata2: ata_sff_flush_pio_task: EXIT [ 295.691803] ata2: EH complete [ 295.691813] sr 1:0:0:0: ioctl_internal_command return code = 8000002 [ 295.691819] : Sense Key : 0xb [current] [descriptor] [ 295.691828] : ASC=0x0 ASCQ=0x0 [ 315.378441] ata1: ata_sff_flush_pio_task: EXIT [ 315.378454] ata1.00: NCQ disabled due to excessive errors [ 315.378460] ata1.00: exception Emask 0x0 SAct 0xff SErr 0x50000 action 0x6 frozen [ 315.378464] ata1: SError: { PHYRdyChg CommWake } [ 315.378469] ata1.00: failed command: WRITE FPDMA QUEUED [ 315.378476] ata1.00: cmd 61/08:00:2b:00:02/00:00:08:00:00/40 tag 0 ncq 4096 out [ 315.378478] res 40/00:00:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout) [ 315.378482] ata1.00: status: { DRDY } [ 315.378484] ata1.00: failed command: WRITE FPDMA QUEUED [ 315.378491] ata1.00: cmd 61/08:08:2b:25:9a/00:00:09:00:00/40 tag 1 ncq 4096 out [ 315.378493] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 315.378496] ata1.00: status: { DRDY } [ 315.378499] ata1.00: failed command: WRITE FPDMA QUEUED [ 315.378506] ata1.00: cmd 61/08:10:e3:94:b7/00:00:09:00:00/40 tag 2 ncq 4096 out [ 315.378507] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 315.378510] ata1.00: status: { DRDY } [ 315.378513] ata1.00: failed command: WRITE FPDMA QUEUED [ 315.378520] ata1.00: cmd 61/08:18:f3:94:b7/00:00:09:00:00/40 tag 3 ncq 4096 out [ 315.378521] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 315.378524] ata1.00: status: { DRDY } [ 315.378527] ata1.00: failed command: WRITE FPDMA QUEUED [ 315.378535] ata1.00: cmd 61/08:20:03:98:b7/00:00:09:00:00/40 tag 4 ncq 4096 out [ 315.378536] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 315.378538] ata1.00: status: { DRDY } [ 315.378540] ata1.00: failed command: WRITE FPDMA QUEUED [ 315.378544] ata1.00: cmd 61/08:28:5b:9f:b7/00:00:09:00:00/40 tag 5 ncq 4096 out [ 315.378545] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 315.378547] ata1.00: status: { DRDY } [ 315.378548] ata1.00: failed command: WRITE FPDMA QUEUED [ 315.378552] ata1.00: cmd 61/10:30:1a:88:3b/00:00:0d:00:00/40 tag 6 ncq 8192 out [ 315.378553] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 315.378555] ata1.00: status: { DRDY } [ 315.378557] ata1.00: failed command: WRITE FPDMA QUEUED [ 315.378561] ata1.00: cmd 61/10:38:db:30:aa/00:00:08:00:00/40 tag 7 ncq 8192 out [ 315.378562] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 315.378564] ata1.00: status: { DRDY } [ 315.378568] ata1: hard resetting link [ 315.682910] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 315.682922] ata1.00: ata_dev_read_id: ENTER [ 315.747557] ata1: ata_sff_flush_pio_task: EXIT [ 315.747698] ata1: ata_sff_flush_pio_task: EXIT [ 315.747712] ata1.00: both IDENTIFYs aborted, assuming NODEV [ 315.747715] ata1.00: revalidation failed (errno=-2) [ 320.674246] ata1: hard resetting link [ 320.978733] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 320.978744] ata1.00: ata_dev_read_id: ENTER [ 320.980141] ata1: ata_sff_flush_pio_task: EXIT [ 320.980151] ata1.00: ata_dev_configure: ENTER [ 320.980161] ata1.00: ata_acpi_push_id: ix = 0, port#: 0 [ 320.980292] ata1.00: ata_dev_get_GTF: ENTER: port#: 0 [ 320.980302] ata1.00: ata_dev_get_GTF: returning gtf=ffff88003f0f33d8, gtf_count=1 [ 320.980649] ata1: ata_sff_flush_pio_task: EXIT [ 320.980667] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04) [ 320.981028] ata1: ata_sff_flush_pio_task: EXIT [ 320.981036] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7469 86:bc09 87:61e3 88:407f [ 320.981409] ata1: ata_sff_flush_pio_task: EXIT [ 320.981415] ata1.00: ata_dev_read_id: ENTER [ 320.982835] ata1: ata_sff_flush_pio_task: EXIT [ 320.982845] ata1.00: ata_dev_configure: ENTER [ 320.982854] ata1.00: ata_acpi_push_id: ix = 0, port#: 0 [ 320.982974] ata1.00: ata_dev_get_GTF: ENTER: port#: 0 [ 320.982982] ata1.00: ata_dev_get_GTF: returning gtf=ffff88003f0f33f8, gtf_count=1 [ 320.983352] ata1: ata_sff_flush_pio_task: EXIT [ 320.983370] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04) [ 320.983702] ata1: ata_sff_flush_pio_task: EXIT [ 320.983711] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7469 86:bc09 87:61e3 88:407f [ 320.983723] ata1.00: configured for UDMA/133 [ 320.985962] ata1: ata_sff_flush_pio_task: EXIT [ 320.985970] ata1.00: device reported invalid CHS sector 0 [ 320.985976] ata1.00: device reported invalid CHS sector 0 [ 320.985980] ata1.00: device reported invalid CHS sector 0 [ 320.985984] ata1.00: device reported invalid CHS sector 0 [ 320.985988] ata1.00: device reported invalid CHS sector 0 [ 320.985992] ata1.00: device reported invalid CHS sector 0 [ 320.985996] ata1.00: device reported invalid CHS sector 0 [ 320.986000] ata1.00: device reported invalid CHS sector 0 [ 320.986033] ata1: EH complete [ 326.367521] ata2: ata_sff_flush_pio_task: EXIT [ 326.367534] ata2: limiting SATA link speed to 1.5 Gbps [ 326.367539] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 326.367546] sr 1:0:0:0: CDB: cdb[0]=0x4a: 4a 01 00 00 10 00 00 00 08 00 [ 326.367561] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 pio 16392 in [ 326.367563] res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout) [ 326.367567] ata2.00: status: { DRDY } [ 326.367573] ata2: hard resetting link [ 326.671889] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 326.671904] ata2.00: ata_dev_read_id: ENTER [ 326.674673] ata2: ata_sff_flush_pio_task: EXIT [ 326.674683] ata2.00: ata_dev_configure: ENTER [ 326.674695] ata2.00: ata_dev_configure: cfg 49:0f00 82:0210 83:5000 84:4000 85:0210 86:1000 87:4000 88:203f [ 326.675627] ata2: ata_sff_flush_pio_task: EXIT [ 326.675633] ata2.00: ata_dev_read_id: ENTER [ 326.675982] ata2: ata_sff_flush_pio_task: EXIT [ 326.675991] ata2.00: ata_dev_configure: ENTER [ 326.676000] ata2.00: ata_dev_configure: cfg 49:0f00 82:0210 83:5000 84:4000 85:0210 86:1000 87:4000 88:203f [ 326.676009] ata2.00: configured for UDMA/100 [ 326.677733] ata2: ata_sff_flush_pio_task: EXIT [ 326.678494] ata2: ata_sff_flush_pio_task: EXIT [ 326.678535] ata2: EH complete [ 351.284511] ata1: ata_sff_flush_pio_task: EXIT [ 351.284529] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x50000 action 0x6 frozen [ 351.284537] ata1: SError: { PHYRdyChg CommWake } [ 351.284543] ata1.00: failed command: WRITE DMA [ 351.284555] ata1.00: cmd ca/00:10:db:30:aa/00:00:00:00:00/e8 tag 0 dma 8192 out [ 351.284557] res 40/00:00:00:00:00/00:00:00:00:00/40 Emask 0x4 (timeout) [ 351.284563] ata1.00: status: { DRDY } [ 351.284572] ata1: hard resetting link [ 351.588978] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 351.588989] ata1.00: ata_dev_read_id: ENTER [ 355.673719] ata1: ata_sff_flush_pio_task: EXIT [ 355.673731] ata1.00: ata_dev_configure: ENTER [ 355.673738] ata1.00: ata_acpi_push_id: ix = 0, port#: 0 [ 355.673870] ata1.00: ata_dev_get_GTF: ENTER: port#: 0 [ 355.673880] ata1.00: ata_dev_get_GTF: returning gtf=ffff880042b5a318, gtf_count=1 [ 355.674792] ata1: ata_sff_flush_pio_task: EXIT [ 355.674812] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04) [ 357.290257] ata2: ata_sff_flush_pio_task: EXIT [ 357.290270] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 357.290276] sr 1:0:0:0: CDB: cdb[0]=0x0: 00 00 00 00 00 00 [ 357.290289] ata2.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 [ 357.290290] res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout) [ 357.290294] ata2.00: status: { DRDY } [ 357.290301] ata2: hard resetting link [ 357.363784] ata1: ata_sff_flush_pio_task: EXIT [ 357.363791] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7469 86:bc09 87:61e3 88:407f [ 357.380160] ata1: ata_sff_flush_pio_task: EXIT [ 357.380165] ata1.00: ata_dev_read_id: ENTER [ 357.381548] ata1: ata_sff_flush_pio_task: EXIT [ 357.381557] ata1.00: ata_dev_configure: ENTER [ 357.381566] ata1.00: ata_acpi_push_id: ix = 0, port#: 0 [ 357.381704] ata1.00: ata_dev_get_GTF: ENTER: port#: 0 [ 357.381714] ata1.00: ata_dev_get_GTF: returning gtf=ffff880042b5a278, gtf_count=1 [ 357.382029] ata1: ata_sff_flush_pio_task: EXIT [ 357.382041] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04) [ 357.382411] ata1: ata_sff_flush_pio_task: EXIT [ 357.382419] ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f09 84:61e3 85:7469 86:bc09 87:61e3 88:407f [ 357.382432] ata1.00: configured for UDMA/133 [ 357.384710] ata1: ata_sff_flush_pio_task: EXIT [ 357.384716] ata1.00: device reported invalid CHS sector 0 [ 357.384738] ata1: EH complete [ 357.594629] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 357.594644] ata2.00: ata_dev_read_id: ENTER [ 357.597414] ata2: ata_sff_flush_pio_task: EXIT [ 357.597424] ata2.00: ata_dev_configure: ENTER [ 357.597435] ata2.00: ata_dev_configure: cfg 49:0f00 82:0210 83:5000 84:4000 85:0210 86:1000 87:4000 88:203f [ 357.598365] ata2: ata_sff_flush_pio_task: EXIT [ 357.598372] ata2.00: ata_dev_read_id: ENTER [ 357.598758] ata2: ata_sff_flush_pio_task: EXIT [ 357.598766] ata2.00: ata_dev_configure: ENTER [ 357.598775] ata2.00: ata_dev_configure: cfg 49:0f00 82:0210 83:5000 84:4000 85:0210 86:1000 87:4000 88:203f [ 357.598785] ata2.00: configured for UDMA/100 [ 357.600473] ata2: ata_sff_flush_pio_task: EXIT [ 357.601238] ata2: ata_sff_flush_pio_task: EXIT [ 357.601276] ata2: EH complete