card, put in low power state [ 26.154137] ieee80211 phy0: U iwl_apm_stop_master stop master [ 26.154179] iwlagn 0000:02:00.0: device EEPROM VER=0x11f, CALIB=0x4 [ 26.154182] iwlagn 0000:02:00.0: Device SKU: 0Xb [ 26.154185] ieee80211 phy0: U iwl_pci_probe MAC address: 00:22:fa:11:39:a4 [ 26.154190] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 26.154216] ieee80211 phy0: U iwlcore_init_geos Channel 1 Freq=2412[2.4GHz] valid flag=0x20 [ 26.154220] ieee80211 phy0: U iwlcore_init_geos Channel 2 Freq=2417[2.4GHz] valid flag=0x20 [ 26.154223] ieee80211 phy0: U iwlcore_init_geos Channel 3 Freq=2422[2.4GHz] valid flag=0x20 [ 26.154227] ieee80211 phy0: U iwlcore_init_geos Channel 4 Freq=2427[2.4GHz] valid flag=0x20 [ 26.154230] ieee80211 phy0: U iwlcore_init_geos Channel 5 Freq=2432[2.4GHz] valid flag=0x0 [ 26.154234] ieee80211 phy0: U iwlcore_init_geos Channel 6 Freq=2437[2.4GHz] valid flag=0x0 [ 26.154237] ieee80211 phy0: U iwlcore_init_geos Channel 7 Freq=2442[2.4GHz] valid flag=0x0 [ 26.154241] ieee80211 phy0: U iwlcore_init_geos Channel 8 Freq=2447[2.4GHz] valid flag=0x10 [ 26.154244] ieee80211 phy0: U iwlcore_init_geos Channel 9 Freq=2452[2.4GHz] valid flag=0x10 [ 26.154248] ieee80211 phy0: U iwlcore_init_geos Channel 10 Freq=2457[2.4GHz] valid flag=0x10 [ 26.154252] ieee80211 phy0: U iwlcore_init_geos Channel 11 Freq=2462[2.4GHz] valid flag=0x10 [ 26.154255] ieee80211 phy0: U iwlcore_init_geos Channel 12 Freq=2467[2.4GHz] valid flag=0x36 [ 26.154259] ieee80211 phy0: U iwlcore_init_geos Channel 13 Freq=2472[2.4GHz] valid flag=0x36 [ 26.154262] ieee80211 phy0: U iwlcore_init_geos Channel 36 Freq=5180[5.2GHz] valid flag=0x26 [ 26.154266] ieee80211 phy0: U iwlcore_init_geos Channel 40 Freq=5200[5.2GHz] valid flag=0x16 [ 26.154269] ieee80211 phy0: U iwlcore_init_geos Channel 44 Freq=5220[5.2GHz] valid flag=0x26 [ 26.154273] ieee80211 phy0: U iwlcore_init_geos Channel 48 Freq=5240[5.2GHz] valid flag=0x16 [ 26.154277] ieee80211 phy0: U iwlcore_init_geos Channel 52 Freq=5260[5.2GHz] valid flag=0x2E [ 26.154280] ieee80211 phy0: U iwlcore_init_geos Channel 56 Freq=5280[5.2GHz] valid flag=0x1E [ 26.154284] ieee80211 phy0: U iwlcore_init_geos Channel 60 Freq=5300[5.2GHz] valid flag=0x2E [ 26.154287] ieee80211 phy0: U iwlcore_init_geos Channel 64 Freq=5320[5.2GHz] valid flag=0x1E [ 26.154291] ieee80211 phy0: U iwlcore_init_geos Channel 100 Freq=5500[5.2GHz] valid flag=0x2E [ 26.154294] ieee80211 phy0: U iwlcore_init_geos Channel 104 Freq=5520[5.2GHz] valid flag=0x1E [ 26.154298] ieee80211 phy0: U iwlcore_init_geos Channel 108 Freq=5540[5.2GHz] valid flag=0x2E [ 26.154302] ieee80211 phy0: U iwlcore_init_geos Channel 112 Freq=5560[5.2GHz] valid flag=0x1E [ 26.154305] ieee80211 phy0: U iwlcore_init_geos Channel 116 Freq=5580[5.2GHz] valid flag=0x2E [ 26.154309] ieee80211 phy0: U iwlcore_init_geos Channel 120 Freq=5600[5.2GHz] valid flag=0x1E [ 26.154312] ieee80211 phy0: U iwlcore_init_geos Channel 124 Freq=5620[5.2GHz] valid flag=0x2E [ 26.154316] ieee80211 phy0: U iwlcore_init_geos Channel 128 Freq=5640[5.2GHz] valid flag=0x1E [ 26.154319] ieee80211 phy0: U iwlcore_init_geos Channel 132 Freq=5660[5.2GHz] valid flag=0x2E [ 26.154323] ieee80211 phy0: U iwlcore_init_geos Channel 136 Freq=5680[5.2GHz] valid flag=0x1E [ 26.154327] ieee80211 phy0: U iwlcore_init_geos Channel 140 Freq=5700[5.2GHz] valid flag=0x3E [ 26.154330] ieee80211 phy0: U iwlcore_init_geos Channel 149 Freq=5745[5.2GHz] valid flag=0x26 [ 26.154334] ieee80211 phy0: U iwlcore_init_geos Channel 153 Freq=5765[5.2GHz] valid flag=0x16 [ 26.154337] ieee80211 phy0: U iwlcore_init_geos Channel 157 Freq=5785[5.2GHz] valid flag=0x26 [ 26.154341] ieee80211 phy0: U iwlcore_init_geos Channel 161 Freq=5805[5.2GHz] valid flag=0x16 [ 26.154344] ieee80211 phy0: U iwlcore_init_geos Channel 165 Freq=5825[5.2GHz] valid flag=0x36 [ 26.154348] iwlagn 0000:02:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels [ 26.154704] iwlagn 0000:02:00.0: irq 42 for MSI/MSI-X [ 26.155305] ieee80211 phy0: U iwl_request_firmware attempting to load firmware EXPERIMENTAL 'iwlwifi-5000-exp.ucode' [ 26.163855] ieee80211 phy0: U iwl_request_firmware attempting to load firmware 'iwlwifi-5000-2.ucode' [ 26.172359] ieee80211 phy0: U iwl_ucode_callback Loaded firmware file 'iwlwifi-5000-2.ucode' (353240 bytes). [ 26.172364] iwlagn 0000:02:00.0: loaded firmware version 8.24.2.12 [ 26.172368] ieee80211 phy0: U iwl_ucode_callback f/w package hdr ucode version raw = 0x818020c [ 26.172371] ieee80211 phy0: U iwl_ucode_callback f/w package hdr runtime inst size = 130700 [ 26.172374] ieee80211 phy0: U iwl_ucode_callback f/w package hdr runtime data size = 49152 [ 26.172377] ieee80211 phy0: U iwl_ucode_callback f/w package hdr init inst size = 124212 [ 26.172380] ieee80211 phy0: U iwl_ucode_callback f/w package hdr init data size = 49152 [ 26.172383] ieee80211 phy0: U iwl_ucode_callback f/w package hdr boot inst size = 0 [ 26.172586] ieee80211 phy0: U iwl_ucode_callback Copying (but not loading) uCode instr len 130700 [ 26.172670] ieee80211 phy0: U iwl_ucode_callback uCode instr buf vaddr = 0xffff88012df80000, paddr = 0x2df80000 [ 26.172674] ieee80211 phy0: U iwl_ucode_callback Copying (but not loading) uCode data len 49152 [ 26.172737] ieee80211 phy0: U iwl_ucode_callback Copying (but not loading) init instr len 124212 [ 26.172816] ieee80211 phy0: U iwl_ucode_callback Copying (but not loading) init data len 49152 [ 26.172830] ieee80211 phy0: U iwl_ucode_callback Copying (but not loading) boot instr len 0 [ 26.219252] cfg80211: Calling CRDA for country: DE [ 26.230848] cfg80211: Regulatory domain changed to country: DE [ 26.230852] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 26.230855] cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 26.230858] cfg80211: (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 26.230861] cfg80211: (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 26.230864] cfg80211: (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm) [ 26.275597] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 27.924289] EXT4-fs (dm-1): re-mounted. Opts: (null) [ 28.297789] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 28.310222] SELinux: initialized (dev sda2, type ext4), uses xattr [ 28.412648] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null) [ 28.412672] SELinux: initialized (dev dm-2, type ext4), uses xattr [ 29.564567] Adding 6127612k swap on /dev/mapper/vg_mako-lv_swap. Priority:-1 extents:1 across:6127612k [ 29.572914] SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts [ 31.271805] auditd (903): /proc/903/oom_adj is deprecated, please use /proc/903/oom_score_adj instead. [ 32.433116] NET: Registered protocol family 10 [ 32.439635] lo: Disabled Privacy Extensions [ 33.093974] ieee80211 phy0: U iwl_prep_station Add STA to driver ID 15: ff:ff:ff:ff:ff:ff [ 33.093994] ieee80211 phy0: U iwl_prepare_card_hw iwl_prepare_card_hw enter [ 33.094090] ieee80211 phy0: U iwl_set_hw_ready hardware ready [ 33.094140] ieee80211 phy0: U iwl_apm_init Init card's basic functions [ 33.114879] ieee80211 phy0: U iwlagn_load_ucode Init ucode found. Loading init ucode... [ 33.114956] ieee80211 phy0: U iwlagn_load_section INST uCode section being loaded... [ 33.118747] ieee80211 phy0: U iwlagn_load_section DATA uCode section being loaded... [ 33.121501] ieee80211 phy0: U iwlagn_load_ucode Init ucode load complete. [ 33.121508] ieee80211 phy0: U __iwl_up iwlagn is coming up [ 33.121514] ieee80211 phy0: U iwlagn_mac_start Start UP work done. [ 33.129791] ieee80211 phy0: I iwl_rx_reply_alive Alive ucode status 0x00000001 revision 0x1 0x9 [ 33.129798] ieee80211 phy0: I iwl_rx_reply_alive Initialization Alive received. [ 33.134338] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 0 [ 33.134342] ieee80211 phy0: U iwl_verify_ucode Bootstrap uCode is good in inst SRAM [ 33.135034] ieee80211 phy0: U iwlagn_tx_queue_set_status Activate AC/CMD Queue 0 on FIFO 3 [ 33.135034] ieee80211 phy0: U iwlagn_tx_queue_set_status Activate AC/CMD Queue 1 on FIFO 2 [ 33.135034] ieee80211 phy0: U iwlagn_tx_queue_set_status Activate AC/CMD Queue 2 on FIFO 1 [ 33.135034] ieee80211 phy0: U iwlagn_tx_queue_set_status Activate AC/CMD Queue 3 on FIFO 0 [ 33.135034] ieee80211 phy0: U iwlagn_tx_queue_set_status Activate AC/CMD Queue 4 on FIFO 7 [ 33.137363] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command COEX_PRIORITY_TABLE_CMD [ 33.137420] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command COEX_PRIORITY_TABLE_CMD [ 33.137578] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command COEX_PRIORITY_TABLE_CMD [ 33.137704] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_PHY_CALIBRATION_CMD [ 33.137709] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_PHY_CALIBRATION_CMD [ 33.137856] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_PHY_CALIBRATION_CMD [ 33.139320] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command CALIBRATION_CFG_CMD [ 33.139325] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command CALIBRATION_CFG_CMD [ 33.139508] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command CALIBRATION_CFG_CMD [ 33.214656] ieee80211 phy0: I iwlagn_rx_calib_complete Init. calibration is completed, restarting fw. [ 33.214846] ieee80211 phy0: U __iwl_down iwlagn is going down [ 33.214913] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode stations in driver [ 33.214924] ieee80211 phy0: U iwl_clear_ucode_stations No active stations found to be cleared [ 33.215489] ieee80211 phy0: U iwl_apm_stop Stop card, put in low power state [ 33.215530] ieee80211 phy0: U iwl_apm_stop_master stop master [ 33.215595] ieee80211 phy0: U iwl_clear_free_frames 0 frames on pre-allocated heap on clear. [ 33.216489] ieee80211 phy0: U iwl_prep_station Add STA to driver ID 15: ff:ff:ff:ff:ff:ff [ 33.216523] ieee80211 phy0: U iwl_prepare_card_hw iwl_prepare_card_hw enter [ 33.216566] ieee80211 phy0: U iwl_set_hw_ready hardware ready [ 33.216594] ieee80211 phy0: U iwl_apm_init Init card's basic functions [ 33.228297] ieee80211 phy0: U iwlagn_load_ucode Init ucode not found, or already loaded. Loading runtime ucode... [ 33.228375] ieee80211 phy0: U iwlagn_load_section INST uCode section being loaded... [ 33.232178] ieee80211 phy0: U iwlagn_load_section DATA uCode section being loaded... [ 33.234948] ieee80211 phy0: U iwlagn_load_ucode Runtime ucode load complete. [ 33.234954] ieee80211 phy0: U __iwl_up iwlagn is coming up [ 33.243243] ieee80211 phy0: I iwl_rx_reply_alive Alive ucode status 0x00000001 revision 0x1 0x0 [ 33.243249] ieee80211 phy0: I iwl_rx_reply_alive Runtime Alive received. [ 33.248304] ieee80211 phy0: U iwl_alive_start Runtime Alive received. [ 33.248307] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 0 [ 33.248310] ieee80211 phy0: U iwl_verify_ucode Bootstrap uCode is good in inst SRAM [ 33.249027] ieee80211 phy0: U iwlagn_tx_queue_set_status Activate AC/CMD Queue 0 on FIFO 3 [ 33.249027] ieee80211 phy0: U iwlagn_tx_queue_set_status Activate AC/CMD Queue 1 on FIFO 2 [ 33.249027] ieee80211 phy0: U iwlagn_tx_queue_set_status Activate AC/CMD Queue 2 on FIFO 1 [ 33.249027] ieee80211 phy0: U iwlagn_tx_queue_set_status Activate AC/CMD Queue 3 on FIFO 0 [ 33.249027] ieee80211 phy0: U iwlagn_tx_queue_set_status Activate AC/CMD Queue 4 on FIFO 7 [ 33.251326] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command COEX_PRIORITY_TABLE_CMD [ 33.251334] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command COEX_PRIORITY_TABLE_CMD [ 33.251429] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command COEX_PRIORITY_TABLE_CMD [ 33.251500] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_PHY_CALIBRATION_CMD [ 33.251504] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_PHY_CALIBRATION_CMD [ 33.251651] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_PHY_CALIBRATION_CMD [ 33.251702] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_PHY_CALIBRATION_CMD [ 33.251706] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_PHY_CALIBRATION_CMD [ 33.251813] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_PHY_CALIBRATION_CMD [ 33.251855] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_PHY_CALIBRATION_CMD [ 33.251859] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_PHY_CALIBRATION_CMD [ 33.251989] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_PHY_CALIBRATION_CMD [ 33.252039] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_PHY_CALIBRATION_CMD [ 33.252052] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_PHY_CALIBRATION_CMD [ 33.252159] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_PHY_CALIBRATION_CMD [ 33.252229] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_PHY_CALIBRATION_CMD [ 33.252237] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_PHY_CALIBRATION_CMD [ 33.252368] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_PHY_CALIBRATION_CMD [ 33.252552] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command TX_ANT_CONFIGURATION_CMD [ 33.252623] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command TX_ANT_CONFIGURATION_CMD [ 33.252726] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command TX_ANT_CONFIGURATION_CMD [ 33.252798] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 33.252869] ieee80211 phy0: U iwl_full_rxon_required need full RXON - !iwl_is_associated_ctx(ctx) [ 33.252878] ieee80211 phy0: U iwlagn_commit_rxon Going to commit RXON [ 33.252880] * without RXON_FILTER_ASSOC_MSK [ 33.252881] * channel = 1 [ 33.252883] * bssid = 00:00:00:00:00:00 [ 33.252889] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON [ 33.252898] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON [ 33.254280] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON [ 33.254357] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode stations in driver [ 33.254365] ieee80211 phy0: U iwl_clear_ucode_stations No active stations found to be cleared [ 33.254368] ieee80211 phy0: U iwl_restore_stations Restoring all known stations ... start. [ 33.254372] ieee80211 phy0: U iwl_restore_stations Restoring sta ff:ff:ff:ff:ff:ff [ 33.254378] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 33.254382] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 33.254386] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 33.255814] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 33.255845] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 33.255849] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 33.255852] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 15 addr ff:ff:ff:ff:ff:ff to uCode [ 33.255856] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 15 addr ff:ff:ff:ff:ff:ff [ 33.255859] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer ff:ff:ff:ff:ff:ff [ 33.255873] ieee80211 phy0: U is_lq_table_valid Channel 1 is not an HT channel [ 33.255876] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 33.255881] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 33.255999] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 33.256695] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 15 [ 33.256700] ieee80211 phy0: U iwl_restore_stations Restoring all known stations .... complete. [ 33.256704] ieee80211 phy0: U iwl_send_rxon_timing beacon interval 100 beacon timer 102400 beacon tim 0 [ 33.256707] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON_TIMING [ 33.256711] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON_TIMING [ 33.256838] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON_TIMING [ 33.256887] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_POWER_DBM_CMD [ 33.256891] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 33.257112] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 33.257165] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_CT_KILL_CONFIG_CMD [ 33.257173] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_CT_KILL_CONFIG_CMD [ 33.257268] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_CT_KILL_CONFIG_CMD [ 33.257321] ieee80211 phy0: U iwl_rf_kill_ct_config REPLY_CT_KILL_CONFIG_CMD succeeded, critical temperature is 110 [ 33.257328] ieee80211 phy0: U iwl_alive_start ALIVE processing complete. [ 33.257346] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command POWER_TABLE_CMD [ 33.257351] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command POWER_TABLE_CMD [ 33.257457] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command POWER_TABLE_CMD [ 33.257528] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 33.257532] ieee80211 phy0: U iwl_alive_start Updated power mode [ 33.257553] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 33.257557] ieee80211 phy0: U iwl_full_rxon_required need full RXON - !iwl_is_associated_ctx(ctx) [ 33.257560] ieee80211 phy0: U iwlagn_commit_rxon Going to commit RXON [ 33.257562] * without RXON_FILTER_ASSOC_MSK [ 33.257563] * channel = 1 [ 33.257563] * bssid = 00:00:00:00:00:00 [ 33.257566] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON [ 33.257577] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON [ 33.257822] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON [ 33.257872] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode stations in driver [ 33.257878] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode active for station 15 [ 33.257881] ieee80211 phy0: U iwl_restore_stations Restoring all known stations ... start. [ 33.257885] ieee80211 phy0: U iwl_restore_stations Restoring sta ff:ff:ff:ff:ff:ff [ 33.257890] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 33.257893] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 33.257898] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 33.258063] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 33.258096] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 33.258100] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 33.258104] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 15 addr ff:ff:ff:ff:ff:ff to uCode [ 33.258108] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 15 addr ff:ff:ff:ff:ff:ff [ 33.258112] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer ff:ff:ff:ff:ff:ff [ 33.258123] ieee80211 phy0: U is_lq_table_valid Channel 1 is not an HT channel [ 33.258127] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 33.258131] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 33.258252] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 33.258284] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 15 [ 33.258289] ieee80211 phy0: U iwl_restore_stations Restoring all known stations .... complete. [ 33.258294] ieee80211 phy0: U iwl_send_rxon_timing beacon interval 100 beacon timer 102400 beacon tim 0 [ 33.258297] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON_TIMING [ 33.258302] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON_TIMING [ 33.258453] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON_TIMING [ 33.258491] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_POWER_DBM_CMD [ 33.258495] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 33.258677] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 33.258717] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 33.258896] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 33.258919] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 33.258935] ieee80211 phy0: U iwl_full_rxon_required need full RXON - !iwl_is_associated_ctx(ctx) [ 33.258940] ieee80211 phy0: U iwlagn_commit_rxon Going to commit RXON [ 33.258941] * without RXON_FILTER_ASSOC_MSK [ 33.258942] * channel = 1 [ 33.258943] * bssid = 00:00:00:00:00:00 [ 33.258946] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON [ 33.258950] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON [ 33.259203] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON [ 33.259288] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode stations in driver [ 33.259292] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode active for station 15 [ 33.259296] ieee80211 phy0: U iwl_restore_stations Restoring all known stations ... start. [ 33.259300] ieee80211 phy0: U iwl_restore_stations Restoring sta ff:ff:ff:ff:ff:ff [ 33.259304] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 33.259308] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 33.259312] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 33.259451] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 33.259480] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 33.259483] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 33.259487] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 15 addr ff:ff:ff:ff:ff:ff to uCode [ 33.259491] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 15 addr ff:ff:ff:ff:ff:ff [ 33.259495] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer ff:ff:ff:ff:ff:ff [ 33.259504] ieee80211 phy0: U is_lq_table_valid Channel 1 is not an HT channel [ 33.259507] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 33.259512] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 33.259634] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 33.259666] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 15 [ 33.259672] ieee80211 phy0: U iwl_restore_stations Restoring all known stations .... complete. [ 33.259676] ieee80211 phy0: U iwl_send_rxon_timing beacon interval 100 beacon timer 102400 beacon tim 0 [ 33.259680] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON_TIMING [ 33.259684] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON_TIMING [ 33.259833] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON_TIMING [ 33.259870] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_POWER_DBM_CMD [ 33.259875] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 33.260058] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 33.260112] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_QOS_PARAM [ 33.260117] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_QOS_PARAM [ 33.260229] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_QOS_PARAM [ 33.260265] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 33.267527] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 33.291740] r8169 0000:03:00.0: eth0: link down [ 33.298923] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 33.346733] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 33.346807] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 33.346816] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 33.348280] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 33.798171] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 33.798183] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 33.799617] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 34.436837] RPC: Registered udp transport module. [ 34.436842] RPC: Registered tcp transport module. [ 34.436845] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 34.453496] SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts [ 36.533628] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 36.533687] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 53.742334] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 53.743070] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 53.745228] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 53.746373] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 54.119092] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 54.119751] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 54.121804] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 56.286252] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 56.287466] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 83.742896] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 83.743184] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 83.743394] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 83.743842] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 84.144153] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 84.144359] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 84.145985] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 86.310412] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 86.311872] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 121.559367] mtrr: base(0xf1000000) is not aligned on a size(0xe00000) boundary [ 123.741884] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 123.741907] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 123.741912] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 123.742155] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 124.161087] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 124.161096] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 124.162497] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 126.327075] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 126.327110] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 180.665932] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 180.665953] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 180.665958] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 180.666191] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 181.014094] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 181.014102] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 181.016102] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 183.180426] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 183.180458] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 183.182638] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 183.182666] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 183.182675] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 183.182957] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 183.186475] wlan0: deauthenticating from 00:1f:3f:1e:b8:4a by local choice (reason=3) [ 183.220063] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 183.220121] wlan0: authenticate with 00:1f:3f:1e:b8:4a (try 1) [ 183.223418] wlan0: authenticated [ 183.223686] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 183.223869] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 183.223880] wlan0: associate with 00:1f:3f:1e:b8:4a (try 1) [ 183.240423] wlan0: RX AssocResp from 00:1f:3f:1e:b8:4a (capab=0x431 status=0 aid=1) [ 183.240429] wlan0: associated [ 183.241095] ieee80211 phy0: U iwlagn_mac_sta_add received request to add station 00:1f:3f:1e:b8:4a [ 183.241139] ieee80211 phy0: U iwlagn_mac_sta_add proceeding to add station 00:1f:3f:1e:b8:4a [ 183.241164] ieee80211 phy0: U iwl_prep_station Add STA to driver ID 0: 00:1f:3f:1e:b8:4a [ 183.241171] ieee80211 phy0: U iwl_set_ht_add_station spatial multiplexing power save mode: disabled [ 183.241180] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 183.241188] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 183.241211] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 183.241423] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 183.241629] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 183.241637] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 183.241644] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 0 addr 00:1f:3f:1e:b8:4a to uCode [ 183.241652] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 0 addr 00:1f:3f:1e:b8:4a [ 183.241659] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer 00:1f:3f:1e:b8:4a [ 183.241703] ieee80211 phy0: U iwlagn_mac_sta_add Initializing rate scaling for station 00:1f:3f:1e:b8:4a [ 183.241718] ieee80211 phy0: U is_lq_table_valid Channel 1 is not an HT channel [ 183.241725] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 183.241734] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 183.242903] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 183.242974] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0 [ 183.246393] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_QOS_PARAM [ 183.246423] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_QOS_PARAM [ 183.247608] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_QOS_PARAM [ 183.248250] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 183.248304] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x6806 active=2 idle=2 [ 183.248329] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x6806 active=2 idle=2 [ 183.248336] ieee80211 phy0: U _iwl_set_rxon_ht rxon flags 0x8005 operation mode :0x0 extension channel offset 0x0 [ 183.248383] ieee80211 phy0: U iwl_full_rxon_required need full RXON - !iwl_is_associated_ctx(ctx) [ 183.248391] ieee80211 phy0: U iwlagn_commit_rxon Going to commit RXON [ 183.248393] * without RXON_FILTER_ASSOC_MSK [ 183.248395] * channel = 1 [ 183.248396] * bssid = 00:00:00:00:00:00 [ 183.248403] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON [ 183.248410] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON [ 183.249134] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON [ 183.250360] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode stations in driver [ 183.250369] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode active for station 0 [ 183.250376] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode active for station 15 [ 183.250382] ieee80211 phy0: U iwl_restore_stations Restoring all known stations ... start. [ 183.250389] ieee80211 phy0: U iwl_restore_stations Restoring sta 00:1f:3f:1e:b8:4a [ 183.250395] ieee80211 phy0: U iwl_restore_stations Restoring sta ff:ff:ff:ff:ff:ff [ 183.250402] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 183.250409] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 183.250417] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 183.250711] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 183.250958] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 183.250965] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 183.250971] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 0 addr 00:1f:3f:1e:b8:4a to uCode [ 183.250978] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 0 addr 00:1f:3f:1e:b8:4a [ 183.250984] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer 00:1f:3f:1e:b8:4a [ 183.251068] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 183.251077] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 183.251323] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 183.251917] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0 [ 183.251930] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 183.251936] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 183.251943] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 183.252192] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 183.254106] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 183.254115] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 183.254121] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 15 addr ff:ff:ff:ff:ff:ff to uCode [ 183.254128] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 15 addr ff:ff:ff:ff:ff:ff [ 183.254134] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer ff:ff:ff:ff:ff:ff [ 183.254152] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 183.254160] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 183.256546] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 183.256597] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 15 [ 183.256604] ieee80211 phy0: U iwl_restore_stations Restoring all known stations .... complete. [ 183.256609] ieee80211 phy0: U iwl_send_rxon_timing beacon interval 100 beacon timer 102400 beacon tim 0 [ 183.256613] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON_TIMING [ 183.256618] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON_TIMING [ 183.256732] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON_TIMING [ 183.256805] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_POWER_DBM_CMD [ 183.256810] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 183.257019] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 183.257040] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_QOS_PARAM [ 183.257044] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_QOS_PARAM [ 183.257140] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_QOS_PARAM [ 183.257220] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 183.257224] ieee80211 phy0: U _iwl_set_rxon_ht rxon flags 0x808025 operation mode :0x1 extension channel offset 0x0 [ 183.257228] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 183.257231] ieee80211 phy0: U iwl_full_rxon_required need full RXON - !iwl_is_associated_ctx(ctx) [ 183.257236] ieee80211 phy0: U iwlagn_commit_rxon Going to commit RXON [ 183.257237] * with RXON_FILTER_ASSOC_MSK [ 183.257238] * channel = 1 [ 183.257238] * bssid = 00:1f:3f:1e:b8:4a [ 183.257242] ieee80211 phy0: U iwl_send_rxon_timing beacon interval 100 beacon timer 102016 beacon tim 0 [ 183.257245] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON_TIMING [ 183.257249] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON_TIMING [ 183.257363] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON_TIMING [ 183.257382] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_QOS_PARAM [ 183.257386] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_QOS_PARAM [ 183.257483] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_QOS_PARAM [ 183.257510] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON [ 183.257514] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON [ 183.257721] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON [ 183.257786] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_REMOVE_STA [ 183.257791] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_REMOVE_STA [ 183.258891] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_REMOVE_STA [ 183.258911] ieee80211 phy0: U iwl_send_remove_station REPLY_REMOVE_STA PASSED [ 183.258922] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 183.258925] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 183.258930] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 183.259055] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 183.259109] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 183.259113] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 183.259117] ieee80211 phy0: U iwl_sta_ucode_activate STA id 0 addr 00:1f:3f:1e:b8:4a already present in uCode (according to driver) [ 183.259121] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 0 addr 00:1f:3f:1e:b8:4a [ 183.259125] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer 00:1f:3f:1e:b8:4a [ 183.259134] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 183.259138] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 183.259264] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 183.259295] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0 [ 183.259301] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_POWER_DBM_CMD [ 183.259305] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 183.259498] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 183.259518] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_PHY_CALIBRATION_CMD [ 183.259522] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_PHY_CALIBRATION_CMD [ 183.259615] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_PHY_CALIBRATION_CMD [ 183.269067] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 184.264679] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 184.264689] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 184.264713] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 184.265239] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 184.265397] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 184.265404] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 184.265412] ieee80211 phy0: U iwl_sta_ucode_activate STA id 0 addr 00:1f:3f:1e:b8:4a already present in uCode (according to driver) [ 184.265420] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 0 addr 00:1f:3f:1e:b8:4a [ 184.265426] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer 00:1f:3f:1e:b8:4a [ 184.266605] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 184.266613] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 184.266621] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 184.266799] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 184.266862] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 184.266869] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 184.266875] ieee80211 phy0: U iwl_sta_ucode_activate STA id 15 addr ff:ff:ff:ff:ff:ff already present in uCode (according to driver) [ 184.266882] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 15 addr ff:ff:ff:ff:ff:ff [ 184.266889] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer ff:ff:ff:ff:ff:ff [ 184.795614] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 184.795624] ieee80211 phy0: U _iwl_set_rxon_ht rxon flags 0x808035 operation mode :0x1 extension channel offset 0x0 [ 184.795632] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 184.876189] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 185.280468] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 185.280478] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 185.280503] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 185.280744] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 185.280874] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 185.280874] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 185.280874] ieee80211 phy0: U iwl_sta_ucode_activate STA id 0 addr 00:1f:3f:1e:b8:4a already present in uCode (according to driver) [ 185.280874] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 0 addr 00:1f:3f:1e:b8:4a [ 185.280874] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer 00:1f:3f:1e:b8:4a [ 193.747030] wlan0: no IPv6 routers present [ 230.450815] iwlagn 0000:02:00.0: Aggregation not enabled for tid 6 because load = 1 [ 233.741756] ieee80211 phy0: U iwlagn_request_scan Scanning while associated... [ 233.741801] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 233.741810] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 233.742278] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 234.641265] ieee80211 phy0: U iwlagn_request_scan Scanning while associated... [ 234.641310] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 234.641318] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 234.643669] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 238.431677] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 238.431689] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 238.431697] ieee80211 phy0: U _iwl_set_rxon_ht rxon flags 0x808035 operation mode :0x0 extension channel offset 0x0 [ 247.247569] iwlagn 0000:02:00.0: Aggregation not enabled for tid 0 because load = 0 [ 247.258761] SELinux: initialized (dev cifs, type cifs), uses genfs_contexts [ 247.265566] mount.cifs used greatest stack depth: 2832 bytes left [ 273.740881] ieee80211 phy0: U iwlagn_request_scan Scanning while associated... [ 273.740897] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 273.740905] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 273.743263] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 274.900300] ieee80211 phy0: U iwlagn_request_scan Scanning while associated... [ 274.900316] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 274.900324] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 274.902680] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 278.690496] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 278.690509] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 278.690516] ieee80211 phy0: U _iwl_set_rxon_ht rxon flags 0x808035 operation mode :0x0 extension channel offset 0x0 [ 288.253546] iwlagn 0000:02:00.0: Aggregation not enabled for tid 0 because load = 0 [ 303.141680] kworker/u:0 used greatest stack depth: 2824 bytes left [ 304.085643] dolphin used greatest stack depth: 2624 bytes left [ 307.695321] iwlagn 0000:02:00.0: Aggregation not enabled for tid 0 because load = 9 [ 310.727152] iwlagn 0000:02:00.0: iwlagn_tx_agg_start on ra = 00:1f:3f:1e:b8:4a tid = 0 [ 310.727186] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 310.727195] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 310.727221] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 310.727516] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 310.727691] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 310.727698] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 310.727704] ieee80211 phy0: U iwl_sta_ucode_activate STA id 0 addr 00:1f:3f:1e:b8:4a already present in uCode (according to driver) [ 310.727712] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 0 addr 00:1f:3f:1e:b8:4a [ 310.727718] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer 00:1f:3f:1e:b8:4a [ 310.727981] ieee80211 phy0: U iwlagn_tx_queue_set_status Activate BA Queue 10 on FIFO 1 [ 333.744655] ieee80211 phy0: U iwlagn_request_scan Scanning while associated... [ 333.744665] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 333.744670] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 333.746091] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 334.824227] ieee80211 phy0: U iwlagn_request_scan Scanning while associated... [ 334.824243] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 334.824251] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 334.826607] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 338.614186] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 338.614198] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 338.614205] ieee80211 phy0: U _iwl_set_rxon_ht rxon flags 0x808035 operation mode :0x0 extension channel offset 0x0 [ 413.741164] ieee80211 phy0: U iwlagn_request_scan Scanning while associated... [ 413.741175] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 413.741180] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 413.741754] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 414.819489] ieee80211 phy0: U iwlagn_request_scan Scanning while associated... [ 414.819502] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 414.819508] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 414.821819] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 418.608812] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 418.608824] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 418.608831] ieee80211 phy0: U _iwl_set_rxon_ht rxon flags 0x808035 operation mode :0x0 extension channel offset 0x0 [ 447.500801] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 447.500811] ieee80211 phy0: U _iwl_set_rxon_ht rxon flags 0x808035 operation mode :0x1 extension channel offset 0x0 [ 447.500819] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 512.229061] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 512.229072] ieee80211 phy0: U _iwl_set_rxon_ht rxon flags 0x4080803D operation mode :0x1 extension channel offset 0x0 [ 512.229079] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 513.745450] ieee80211 phy0: U iwlagn_request_scan Scanning while associated... [ 513.745462] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 513.745467] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 513.747789] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 514.680132] ieee80211 phy0: U iwlagn_request_scan Scanning while associated... [ 514.680149] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 514.680156] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 514.682519] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 518.469252] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 518.469265] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 518.469272] ieee80211 phy0: U _iwl_set_rxon_ht rxon flags 0x808035 operation mode :0x0 extension channel offset 0x0 [ 518.484739] ieee80211 phy0: U iwlagn_tx_queue_set_status Deactivate AC/CMD Queue 10 on FIFO 1 [ 518.484932] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 518.484936] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 518.484951] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 518.485111] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 518.485383] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 518.485388] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 518.485392] ieee80211 phy0: U iwl_sta_ucode_activate STA id 0 addr 00:1f:3f:1e:b8:4a already present in uCode (according to driver) [ 518.485397] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 0 addr 00:1f:3f:1e:b8:4a [ 518.485401] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer 00:1f:3f:1e:b8:4a [ 518.485737] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_QOS_PARAM [ 518.485753] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_QOS_PARAM [ 518.486510] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_QOS_PARAM [ 518.486589] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 518.486593] ieee80211 phy0: U _iwl_set_rxon_ht rxon flags 0x808015 operation mode :0x1 extension channel offset 0x0 [ 518.486597] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 518.486601] ieee80211 phy0: U iwl_full_rxon_required need full RXON - compare_ether_addr(staging->bssid_addr, active->bssid_addr) [ 518.486606] ieee80211 phy0: U iwlagn_commit_rxon Going to commit RXON [ 518.486607] * with RXON_FILTER_ASSOC_MSK [ 518.486608] * channel = 1 [ 518.486609] * bssid = 00:00:00:00:00:00 [ 518.486612] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON [ 518.486616] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON [ 518.486893] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON [ 518.486956] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode stations in driver [ 518.486971] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode active for station 0 [ 518.486974] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode active for station 15 [ 518.486978] ieee80211 phy0: U iwl_restore_stations Restoring all known stations ... start. [ 518.486982] ieee80211 phy0: U iwl_restore_stations Restoring sta 00:1f:3f:1e:b8:4a [ 518.486985] ieee80211 phy0: U iwl_restore_stations Restoring sta ff:ff:ff:ff:ff:ff [ 518.486989] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 518.486992] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 518.486996] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 518.487131] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 518.488408] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 518.488412] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 518.488415] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 0 addr 00:1f:3f:1e:b8:4a to uCode [ 518.488418] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 0 addr 00:1f:3f:1e:b8:4a [ 518.488422] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer 00:1f:3f:1e:b8:4a [ 518.488452] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 518.488456] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 518.488612] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 518.488643] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0 [ 518.488649] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 518.488653] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 518.488657] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 518.488810] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 518.488831] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 518.488834] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 518.488838] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 15 addr ff:ff:ff:ff:ff:ff to uCode [ 518.488841] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 15 addr ff:ff:ff:ff:ff:ff [ 518.488844] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer ff:ff:ff:ff:ff:ff [ 518.488852] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 518.488857] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 518.489007] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 518.490421] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 15 [ 518.490426] ieee80211 phy0: U iwl_restore_stations Restoring all known stations .... complete. [ 518.490431] ieee80211 phy0: U iwl_send_rxon_timing beacon interval 100 beacon timer 102016 beacon tim 0 [ 518.490434] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON_TIMING [ 518.490438] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON_TIMING [ 518.490577] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON_TIMING [ 518.490608] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_QOS_PARAM [ 518.490612] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_QOS_PARAM [ 518.490731] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_QOS_PARAM [ 518.490761] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON [ 518.490765] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON [ 518.490990] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON [ 518.491067] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_REMOVE_STA [ 518.491071] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_REMOVE_STA [ 518.491294] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_REMOVE_STA [ 518.492311] ieee80211 phy0: U iwl_send_remove_station REPLY_REMOVE_STA PASSED [ 518.492322] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 518.492325] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 518.492329] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 518.492463] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 518.492829] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 518.492833] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 518.492837] ieee80211 phy0: U iwl_sta_ucode_activate STA id 0 addr 00:1f:3f:1e:b8:4a already present in uCode (according to driver) [ 518.492841] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 0 addr 00:1f:3f:1e:b8:4a [ 518.492844] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer 00:1f:3f:1e:b8:4a [ 518.492853] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 518.492857] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 518.492995] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 518.493160] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0 [ 518.493203] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_POWER_DBM_CMD [ 518.493207] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 518.493396] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 518.493705] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 518.493779] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_QOS_PARAM [ 518.493784] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_QOS_PARAM [ 518.493942] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_QOS_PARAM [ 518.494071] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 518.494076] ieee80211 phy0: U iwl_full_rxon_required need full RXON - staging->filter_flags & RXON_FILTER_ASSOC_MSK != active->filter_flags & RXON_FILTER_ASSOC_MSK - 0 != 32 [ 518.494081] ieee80211 phy0: U iwlagn_commit_rxon Going to commit RXON [ 518.494082] * without RXON_FILTER_ASSOC_MSK [ 518.494083] * channel = 1 [ 518.494084] * bssid = 00:00:00:00:00:00 [ 518.494087] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON [ 518.494091] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON [ 518.494350] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON [ 518.494451] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode stations in driver [ 518.494456] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode active for station 0 [ 518.494459] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode active for station 15 [ 518.494463] ieee80211 phy0: U iwl_restore_stations Restoring all known stations ... start. [ 518.494467] ieee80211 phy0: U iwl_restore_stations Restoring sta 00:1f:3f:1e:b8:4a [ 518.494470] ieee80211 phy0: U iwl_restore_stations Restoring sta ff:ff:ff:ff:ff:ff [ 518.494474] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 518.494478] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 518.494482] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 518.494612] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 518.497177] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 518.497181] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 518.497185] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 0 addr 00:1f:3f:1e:b8:4a to uCode [ 518.497189] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 0 addr 00:1f:3f:1e:b8:4a [ 518.497192] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer 00:1f:3f:1e:b8:4a [ 518.497203] ieee80211 phy0: U is_lq_table_valid Channel 1 is not an HT channel [ 518.497206] ieee80211 phy0: U is_lq_table_valid index 0 of LQ expects HT channel [ 518.497209] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0 [ 518.497215] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 518.497243] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 518.497247] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 518.497380] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 518.497412] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 518.497417] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 518.497420] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 15 addr ff:ff:ff:ff:ff:ff to uCode [ 518.497424] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 15 addr ff:ff:ff:ff:ff:ff [ 518.497427] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer ff:ff:ff:ff:ff:ff [ 518.497437] ieee80211 phy0: U is_lq_table_valid Channel 1 is not an HT channel [ 518.497440] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 518.497444] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 518.497573] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 518.497601] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 15 [ 518.497606] ieee80211 phy0: U iwl_restore_stations Restoring all known stations .... complete. [ 518.497611] ieee80211 phy0: U iwl_send_rxon_timing beacon interval 100 beacon timer 102016 beacon tim 0 [ 518.497615] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON_TIMING [ 518.497619] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON_TIMING [ 518.497753] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON_TIMING [ 518.497784] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_POWER_DBM_CMD [ 518.497788] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 518.497979] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 518.498685] iwlagn 0000:02:00.0: Stopping AGG while state not ON or starting [ 518.498796] ieee80211 phy0: U iwlagn_tx_queue_set_status Deactivate AC/CMD Queue 10 on FIFO 1 [ 518.498809] ieee80211 phy0: U is_lq_table_valid Channel 1 is not an HT channel [ 518.498812] ieee80211 phy0: U is_lq_table_valid index 0 of LQ expects HT channel [ 518.498907] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 518.498911] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 518.498926] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 518.501858] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 518.501969] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 518.501973] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 518.501977] ieee80211 phy0: U iwl_sta_ucode_activate STA id 0 addr 00:1f:3f:1e:b8:4a already present in uCode (according to driver) [ 518.501981] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 0 addr 00:1f:3f:1e:b8:4a [ 518.501984] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer 00:1f:3f:1e:b8:4a [ 518.502474] ieee80211 phy0: U iwl_mac_sta_remove received request to remove station 00:1f:3f:1e:b8:4a [ 518.502487] ieee80211 phy0: U iwl_mac_sta_remove proceeding to remove station 00:1f:3f:1e:b8:4a [ 518.502490] ieee80211 phy0: U iwl_remove_station Removing STA from driver:0 00:1f:3f:1e:b8:4a [ 518.502505] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_REMOVE_STA [ 518.502520] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_REMOVE_STA [ 518.502703] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_REMOVE_STA [ 518.502801] ieee80211 phy0: U iwl_sta_ucode_deactivate Removed STA 0 [ 518.502804] ieee80211 phy0: U iwl_send_remove_station REPLY_REMOVE_STA PASSED [ 518.504487] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 518.504671] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 518.504676] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 518.504690] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 518.505729] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 518.505822] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 518.505829] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 518.505835] ieee80211 phy0: U iwl_sta_ucode_activate STA id 15 addr ff:ff:ff:ff:ff:ff already present in uCode (according to driver) [ 518.505843] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 15 addr ff:ff:ff:ff:ff:ff [ 518.505849] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer ff:ff:ff:ff:ff:ff [ 518.506911] cfg80211: Calling CRDA to update world regulatory domain [ 518.562384] cfg80211: World regulatory domain updated: [ 518.562388] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 518.562392] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 518.562395] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 518.562398] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 518.562402] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 518.562405] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 518.562620] cfg80211: Calling CRDA for country: DE [ 518.573947] cfg80211: Regulatory domain changed to country: DE [ 518.573951] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 518.573954] cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 518.573957] cfg80211: (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 518.573960] cfg80211: (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 518.573963] cfg80211: (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm) [ 518.607133] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 518.607165] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 518.607173] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 518.607468] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 519.004993] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 519.005000] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 519.006462] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 521.171136] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 521.171158] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 521.171936] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 521.171991] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 521.172661] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 521.172674] wlan0: authenticate with 00:1f:3f:1e:b8:4a (try 1) [ 521.175857] wlan0: authenticated [ 521.175917] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 521.175982] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 521.175991] wlan0: associate with 00:1f:3f:1e:b8:4a (try 1) [ 521.180621] wlan0: RX AssocResp from 00:1f:3f:1e:b8:4a (capab=0x431 status=0 aid=1) [ 521.180625] wlan0: associated [ 521.180663] ieee80211 phy0: U iwlagn_mac_sta_add received request to add station 00:1f:3f:1e:b8:4a [ 521.180668] ieee80211 phy0: U iwlagn_mac_sta_add proceeding to add station 00:1f:3f:1e:b8:4a [ 521.180673] ieee80211 phy0: U iwl_prep_station Add STA to driver ID 0: 00:1f:3f:1e:b8:4a [ 521.180677] ieee80211 phy0: U iwl_set_ht_add_station spatial multiplexing power save mode: disabled [ 521.180682] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 521.180686] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 521.180690] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 521.180848] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 521.180871] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 521.180875] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 521.180878] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 0 addr 00:1f:3f:1e:b8:4a to uCode [ 521.180882] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 0 addr 00:1f:3f:1e:b8:4a [ 521.180886] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer 00:1f:3f:1e:b8:4a [ 521.180894] ieee80211 phy0: U iwlagn_mac_sta_add Initializing rate scaling for station 00:1f:3f:1e:b8:4a [ 521.180902] ieee80211 phy0: U is_lq_table_valid Channel 1 is not an HT channel [ 521.180906] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 521.180910] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 521.181075] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 521.182784] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0 [ 521.183915] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_QOS_PARAM [ 521.183921] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_QOS_PARAM [ 521.184212] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_QOS_PARAM [ 521.184486] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 521.184495] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 521.184500] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 521.184504] ieee80211 phy0: U _iwl_set_rxon_ht rxon flags 0x8005 operation mode :0x0 extension channel offset 0x0 [ 521.184515] ieee80211 phy0: U iwl_full_rxon_required need full RXON - !iwl_is_associated_ctx(ctx) [ 521.184519] ieee80211 phy0: U iwlagn_commit_rxon Going to commit RXON [ 521.184521] * without RXON_FILTER_ASSOC_MSK [ 521.184521] * channel = 1 [ 521.184522] * bssid = 00:00:00:00:00:00 [ 521.184525] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON [ 521.184529] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON [ 521.185152] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON [ 521.186072] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode stations in driver [ 521.186076] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode active for station 0 [ 521.186080] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode active for station 15 [ 521.186084] ieee80211 phy0: U iwl_restore_stations Restoring all known stations ... start. [ 521.186088] ieee80211 phy0: U iwl_restore_stations Restoring sta 00:1f:3f:1e:b8:4a [ 521.186091] ieee80211 phy0: U iwl_restore_stations Restoring sta ff:ff:ff:ff:ff:ff [ 521.186095] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 521.186098] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 521.186102] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 521.186330] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 521.186353] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 521.186356] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 521.186360] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 0 addr 00:1f:3f:1e:b8:4a to uCode [ 521.186363] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 0 addr 00:1f:3f:1e:b8:4a [ 521.186367] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer 00:1f:3f:1e:b8:4a [ 521.186378] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 521.186382] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 521.186533] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 521.186564] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0 [ 521.186570] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 521.186573] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 521.186577] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 521.187937] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 521.188587] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 521.188591] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 521.188594] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 15 addr ff:ff:ff:ff:ff:ff to uCode [ 521.188598] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 15 addr ff:ff:ff:ff:ff:ff [ 521.188602] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer ff:ff:ff:ff:ff:ff [ 521.188610] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 521.188614] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 521.188768] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 521.188807] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 15 [ 521.188812] ieee80211 phy0: U iwl_restore_stations Restoring all known stations .... complete. [ 521.188817] ieee80211 phy0: U iwl_send_rxon_timing beacon interval 100 beacon timer 102016 beacon tim 0 [ 521.188821] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON_TIMING [ 521.188825] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON_TIMING [ 521.188963] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON_TIMING [ 521.189054] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_POWER_DBM_CMD [ 521.189058] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 521.189360] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 521.189393] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_QOS_PARAM [ 521.189398] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_QOS_PARAM [ 521.189534] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_QOS_PARAM [ 521.189602] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 521.189606] ieee80211 phy0: U _iwl_set_rxon_ht rxon flags 0x808025 operation mode :0x1 extension channel offset 0x0 [ 521.189610] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 521.189613] ieee80211 phy0: U iwl_full_rxon_required need full RXON - !iwl_is_associated_ctx(ctx) [ 521.189617] ieee80211 phy0: U iwlagn_commit_rxon Going to commit RXON [ 521.189618] * with RXON_FILTER_ASSOC_MSK [ 521.189619] * channel = 1 [ 521.189620] * bssid = 00:1f:3f:1e:b8:4a [ 521.189624] ieee80211 phy0: U iwl_send_rxon_timing beacon interval 100 beacon timer 102016 beacon tim 0 [ 521.189627] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON_TIMING [ 521.189631] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON_TIMING [ 521.189833] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON_TIMING [ 521.189876] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_QOS_PARAM [ 521.189880] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_QOS_PARAM [ 521.189979] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_QOS_PARAM [ 521.190045] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON [ 521.190049] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON [ 521.190395] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON [ 521.190494] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_REMOVE_STA [ 521.190499] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_REMOVE_STA [ 521.190617] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_REMOVE_STA [ 521.190644] ieee80211 phy0: U iwl_send_remove_station REPLY_REMOVE_STA PASSED [ 521.190653] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 521.190657] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 521.190661] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 521.190789] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 521.190848] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 521.190852] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 521.190855] ieee80211 phy0: U iwl_sta_ucode_activate STA id 0 addr 00:1f:3f:1e:b8:4a already present in uCode (according to driver) [ 521.190859] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 0 addr 00:1f:3f:1e:b8:4a [ 521.190863] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer 00:1f:3f:1e:b8:4a [ 521.190872] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 521.190876] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 521.191102] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 521.191433] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0 [ 521.191440] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_POWER_DBM_CMD [ 521.191444] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 521.191654] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 521.212581] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 521.212587] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 521.212592] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 521.213645] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 521.213727] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 521.213734] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 521.213741] ieee80211 phy0: U iwl_sta_ucode_activate STA id 0 addr 00:1f:3f:1e:b8:4a already present in uCode (according to driver) [ 521.213749] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 0 addr 00:1f:3f:1e:b8:4a [ 521.213755] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer 00:1f:3f:1e:b8:4a [ 521.214207] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 521.214211] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 521.214215] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 521.214354] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 521.215599] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 521.215606] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 521.215613] ieee80211 phy0: U iwl_sta_ucode_activate STA id 15 addr ff:ff:ff:ff:ff:ff already present in uCode (according to driver) [ 521.215620] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 15 addr ff:ff:ff:ff:ff:ff [ 521.215627] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer ff:ff:ff:ff:ff:ff [ 524.680453] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 524.680464] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 524.680468] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 524.680596] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 524.680620] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 524.680625] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 524.680629] ieee80211 phy0: U iwl_sta_ucode_activate STA id 0 addr 00:1f:3f:1e:b8:4a already present in uCode (according to driver) [ 524.680634] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 0 addr 00:1f:3f:1e:b8:4a [ 524.680637] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer 00:1f:3f:1e:b8:4a [ 527.282085] CIFS VFS: No response to cmd 46 mid 6964 [ 527.282104] CIFS VFS: Send error in read = -11 [ 534.375113] CIFS VFS: No response for cmd 50 mid 6965 [ 537.844729] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 537.844740] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 537.844748] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 537.844941] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 537.845560] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 537.845568] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 537.845574] ieee80211 phy0: U iwl_sta_ucode_activate STA id 15 addr ff:ff:ff:ff:ff:ff already present in uCode (according to driver) [ 537.845582] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 15 addr ff:ff:ff:ff:ff:ff [ 537.845589] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer ff:ff:ff:ff:ff:ff [ 538.853811] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 538.853817] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 538.853822] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 538.853978] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 538.854041] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 538.854045] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 538.854048] ieee80211 phy0: U iwl_sta_ucode_activate STA id 15 addr ff:ff:ff:ff:ff:ff already present in uCode (according to driver) [ 538.854053] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 15 addr ff:ff:ff:ff:ff:ff [ 538.854056] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer ff:ff:ff:ff:ff:ff [ 538.854966] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 538.854974] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 538.854982] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 538.857057] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 538.857171] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 538.857180] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 538.857186] ieee80211 phy0: U iwl_sta_ucode_activate STA id 15 addr ff:ff:ff:ff:ff:ff already present in uCode (according to driver) [ 538.857194] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 15 addr ff:ff:ff:ff:ff:ff [ 538.857200] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer ff:ff:ff:ff:ff:ff [ 539.863973] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 539.863983] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 539.863991] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 539.864159] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 539.864216] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 539.864223] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 539.864229] ieee80211 phy0: U iwl_sta_ucode_activate STA id 15 addr ff:ff:ff:ff:ff:ff already present in uCode (according to driver) [ 539.864237] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 15 addr ff:ff:ff:ff:ff:ff [ 539.864243] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer ff:ff:ff:ff:ff:ff [ 539.864931] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 539.864938] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 539.864945] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 539.865112] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 539.866086] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 539.866096] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 539.866104] ieee80211 phy0: U iwl_sta_ucode_activate STA id 15 addr ff:ff:ff:ff:ff:ff already present in uCode (according to driver) [ 539.866112] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 15 addr ff:ff:ff:ff:ff:ff [ 539.866119] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer ff:ff:ff:ff:ff:ff [ 540.874063] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 540.874069] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 540.874074] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 540.874578] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 540.874603] wlan0: deauthenticated from 00:1f:3f:1e:b8:4a (Reason: 2) [ 540.875044] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 540.875052] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 540.875059] ieee80211 phy0: U iwl_sta_ucode_activate STA id 15 addr ff:ff:ff:ff:ff:ff already present in uCode (according to driver) [ 540.875066] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 15 addr ff:ff:ff:ff:ff:ff [ 540.875073] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer ff:ff:ff:ff:ff:ff [ 540.875781] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 540.875789] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 540.875797] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 540.875993] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 540.876059] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 540.876068] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 540.876075] ieee80211 phy0: U iwl_sta_ucode_activate STA id 15 addr ff:ff:ff:ff:ff:ff already present in uCode (according to driver) [ 540.876083] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 15 addr ff:ff:ff:ff:ff:ff [ 540.876090] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer ff:ff:ff:ff:ff:ff [ 540.877633] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 540.877642] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 540.877650] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 540.877846] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 540.877889] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 540.877896] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 540.877903] ieee80211 phy0: U iwl_sta_ucode_activate STA id 0 addr 00:1f:3f:1e:b8:4a already present in uCode (according to driver) [ 540.877911] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 0 addr 00:1f:3f:1e:b8:4a [ 540.877917] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer 00:1f:3f:1e:b8:4a [ 540.878068] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_QOS_PARAM [ 540.878076] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_QOS_PARAM [ 540.878207] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_QOS_PARAM [ 540.879628] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 540.879636] ieee80211 phy0: U _iwl_set_rxon_ht rxon flags 0x808015 operation mode :0x1 extension channel offset 0x0 [ 540.879643] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 540.879650] ieee80211 phy0: U iwl_full_rxon_required need full RXON - compare_ether_addr(staging->bssid_addr, active->bssid_addr) [ 540.879659] ieee80211 phy0: U iwlagn_commit_rxon Going to commit RXON [ 540.879661] * with RXON_FILTER_ASSOC_MSK [ 540.879662] * channel = 1 [ 540.879664] * bssid = 00:00:00:00:00:00 [ 540.879670] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON [ 540.879677] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON [ 540.879992] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON [ 540.880064] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode stations in driver [ 540.880072] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode active for station 0 [ 540.880079] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode active for station 15 [ 540.880085] ieee80211 phy0: U iwl_restore_stations Restoring all known stations ... start. [ 540.880092] ieee80211 phy0: U iwl_restore_stations Restoring sta 00:1f:3f:1e:b8:4a [ 540.880097] ieee80211 phy0: U iwl_restore_stations Restoring sta ff:ff:ff:ff:ff:ff [ 540.880104] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 540.880111] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 540.880118] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 540.880292] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 540.880328] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 540.880334] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 540.880340] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 0 addr 00:1f:3f:1e:b8:4a to uCode [ 540.880347] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 0 addr 00:1f:3f:1e:b8:4a [ 540.880353] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer 00:1f:3f:1e:b8:4a [ 540.880369] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 540.880377] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 540.880571] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 540.880646] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0 [ 540.880659] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 540.880666] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 540.880674] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 540.880846] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 540.880885] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 540.880892] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 540.880899] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 15 addr ff:ff:ff:ff:ff:ff to uCode [ 540.880907] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 15 addr ff:ff:ff:ff:ff:ff [ 540.880914] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer ff:ff:ff:ff:ff:ff [ 540.880930] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 540.880939] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 540.881104] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 540.884093] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 15 [ 540.884103] ieee80211 phy0: U iwl_restore_stations Restoring all known stations .... complete. [ 540.884112] ieee80211 phy0: U iwl_send_rxon_timing beacon interval 100 beacon timer 102016 beacon tim 0 [ 540.884118] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON_TIMING [ 540.884126] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON_TIMING [ 540.884296] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON_TIMING [ 540.884370] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_QOS_PARAM [ 540.884378] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_QOS_PARAM [ 540.884709] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_QOS_PARAM [ 540.884765] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON [ 540.884773] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON [ 540.885054] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON [ 540.885161] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_REMOVE_STA [ 540.885170] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_REMOVE_STA [ 540.885306] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_REMOVE_STA [ 540.885376] ieee80211 phy0: U iwl_send_remove_station REPLY_REMOVE_STA PASSED [ 540.885391] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 540.885397] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 540.885405] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 540.885572] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 540.885607] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 540.885613] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 540.885620] ieee80211 phy0: U iwl_sta_ucode_activate STA id 0 addr 00:1f:3f:1e:b8:4a already present in uCode (according to driver) [ 540.885627] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 0 addr 00:1f:3f:1e:b8:4a [ 540.885633] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer 00:1f:3f:1e:b8:4a [ 540.885648] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 540.885656] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 540.885824] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 540.885876] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0 [ 540.885947] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_POWER_DBM_CMD [ 540.885955] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 540.886183] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 540.886283] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 540.886384] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_QOS_PARAM [ 540.886392] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_QOS_PARAM [ 540.886563] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_QOS_PARAM [ 540.886619] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 540.886627] ieee80211 phy0: U iwl_full_rxon_required need full RXON - staging->filter_flags & RXON_FILTER_ASSOC_MSK != active->filter_flags & RXON_FILTER_ASSOC_MSK - 0 != 32 [ 540.886636] ieee80211 phy0: U iwlagn_commit_rxon Going to commit RXON [ 540.886638] * without RXON_FILTER_ASSOC_MSK [ 540.886640] * channel = 1 [ 540.886641] * bssid = 00:00:00:00:00:00 [ 540.886647] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON [ 540.886654] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON [ 540.886955] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON [ 540.887114] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode stations in driver [ 540.887121] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode active for station 0 [ 540.887127] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode active for station 15 [ 540.887133] ieee80211 phy0: U iwl_restore_stations Restoring all known stations ... start. [ 540.887140] ieee80211 phy0: U iwl_restore_stations Restoring sta 00:1f:3f:1e:b8:4a [ 540.887146] ieee80211 phy0: U iwl_restore_stations Restoring sta ff:ff:ff:ff:ff:ff [ 540.887153] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 540.887159] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 540.887166] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 540.887328] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 540.887363] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 540.887370] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 540.887376] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 0 addr 00:1f:3f:1e:b8:4a to uCode [ 540.887382] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 0 addr 00:1f:3f:1e:b8:4a [ 540.887388] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer 00:1f:3f:1e:b8:4a [ 540.887403] ieee80211 phy0: U is_lq_table_valid Channel 1 is not an HT channel [ 540.887409] ieee80211 phy0: U is_lq_table_valid index 0 of LQ expects HT channel [ 540.887415] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0 [ 540.887424] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 540.887430] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 540.887438] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 540.887599] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 540.887633] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 540.887640] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 540.887646] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 15 addr ff:ff:ff:ff:ff:ff to uCode [ 540.887652] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 15 addr ff:ff:ff:ff:ff:ff [ 540.887658] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer ff:ff:ff:ff:ff:ff [ 540.887674] ieee80211 phy0: U is_lq_table_valid Channel 1 is not an HT channel [ 540.887679] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 540.887687] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 540.887843] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 540.887895] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 15 [ 540.887904] ieee80211 phy0: U iwl_restore_stations Restoring all known stations .... complete. [ 540.887911] ieee80211 phy0: U iwl_send_rxon_timing beacon interval 100 beacon timer 102016 beacon tim 0 [ 540.887917] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON_TIMING [ 540.887925] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON_TIMING [ 540.888086] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON_TIMING [ 540.888140] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_POWER_DBM_CMD [ 540.888148] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 540.888368] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 540.888526] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 540.888532] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 540.888540] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 540.888715] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 540.888760] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 540.888767] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 540.888773] ieee80211 phy0: U iwl_sta_ucode_activate STA id 0 addr 00:1f:3f:1e:b8:4a already present in uCode (according to driver) [ 540.888781] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 0 addr 00:1f:3f:1e:b8:4a [ 540.888787] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer 00:1f:3f:1e:b8:4a [ 540.889344] ieee80211 phy0: U iwl_mac_sta_remove received request to remove station 00:1f:3f:1e:b8:4a [ 540.889352] ieee80211 phy0: U iwl_mac_sta_remove proceeding to remove station 00:1f:3f:1e:b8:4a [ 540.889359] ieee80211 phy0: U iwl_remove_station Removing STA from driver:0 00:1f:3f:1e:b8:4a [ 540.889367] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_REMOVE_STA [ 540.889374] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_REMOVE_STA [ 540.889508] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_REMOVE_STA [ 540.892774] ieee80211 phy0: U iwl_sta_ucode_deactivate Removed STA 0 [ 540.892781] ieee80211 phy0: U iwl_send_remove_station REPLY_REMOVE_STA PASSED [ 540.899470] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 540.899592] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 540.899596] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 540.899601] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 540.899744] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 540.899778] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 540.899783] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 540.899787] ieee80211 phy0: U iwl_sta_ucode_activate STA id 15 addr ff:ff:ff:ff:ff:ff already present in uCode (according to driver) [ 540.899792] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 15 addr ff:ff:ff:ff:ff:ff [ 540.899796] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer ff:ff:ff:ff:ff:ff [ 540.900726] cfg80211: Calling CRDA to update world regulatory domain [ 540.919971] cfg80211: World regulatory domain updated: [ 540.919974] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 540.919978] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 540.919981] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 540.919985] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 540.919988] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 540.919991] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 540.920094] cfg80211: Calling CRDA for country: DE [ 540.931750] cfg80211: Regulatory domain changed to country: DE [ 540.931755] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 540.931759] cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 540.931764] cfg80211: (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 540.931768] cfg80211: (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 540.931772] cfg80211: (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm) [ 541.000744] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 541.000773] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 541.000781] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 541.001098] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 541.422671] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_SCAN_CMD [ 541.422679] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_SCAN_CMD [ 541.424075] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_SCAN_CMD [ 543.588686] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 543.588716] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 543.589375] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 543.589388] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 543.589597] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 543.589616] wlan0: authenticate with 00:1f:3f:1e:b8:4a (try 1) [ 543.594614] wlan0: authenticated [ 543.594748] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 543.594862] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 543.594878] wlan0: associate with 00:1f:3f:1e:b8:4a (try 1) [ 543.599417] wlan0: RX AssocResp from 00:1f:3f:1e:b8:4a (capab=0x431 status=0 aid=1) [ 543.599425] wlan0: associated [ 543.599496] ieee80211 phy0: U iwlagn_mac_sta_add received request to add station 00:1f:3f:1e:b8:4a [ 543.599506] ieee80211 phy0: U iwlagn_mac_sta_add proceeding to add station 00:1f:3f:1e:b8:4a [ 543.599514] ieee80211 phy0: U iwl_prep_station Add STA to driver ID 0: 00:1f:3f:1e:b8:4a [ 543.599521] ieee80211 phy0: U iwl_set_ht_add_station spatial multiplexing power save mode: disabled [ 543.599529] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 543.599536] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 543.599544] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 543.600078] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 543.601636] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 543.601644] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 543.601651] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 0 addr 00:1f:3f:1e:b8:4a to uCode [ 543.601658] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 0 addr 00:1f:3f:1e:b8:4a [ 543.601664] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer 00:1f:3f:1e:b8:4a [ 543.601680] ieee80211 phy0: U iwlagn_mac_sta_add Initializing rate scaling for station 00:1f:3f:1e:b8:4a [ 543.601694] ieee80211 phy0: U is_lq_table_valid Channel 1 is not an HT channel [ 543.601700] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 543.601708] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 543.601902] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 543.601963] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0 [ 543.602799] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_QOS_PARAM [ 543.602807] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_QOS_PARAM [ 543.603170] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_QOS_PARAM [ 543.604099] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2406 active=2 idle=1 [ 543.604114] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 543.604122] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 543.604129] ieee80211 phy0: U _iwl_set_rxon_ht rxon flags 0x8005 operation mode :0x0 extension channel offset 0x0 [ 543.604147] ieee80211 phy0: U iwl_full_rxon_required need full RXON - !iwl_is_associated_ctx(ctx) [ 543.604155] ieee80211 phy0: U iwlagn_commit_rxon Going to commit RXON [ 543.604158] * without RXON_FILTER_ASSOC_MSK [ 543.604159] * channel = 1 [ 543.604161] * bssid = 00:00:00:00:00:00 [ 543.604167] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON [ 543.604174] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON [ 543.605273] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON [ 543.605352] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode stations in driver [ 543.605356] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode active for station 0 [ 543.605360] ieee80211 phy0: U iwl_clear_ucode_stations Clearing ucode active for station 15 [ 543.605364] ieee80211 phy0: U iwl_restore_stations Restoring all known stations ... start. [ 543.605368] ieee80211 phy0: U iwl_restore_stations Restoring sta 00:1f:3f:1e:b8:4a [ 543.605371] ieee80211 phy0: U iwl_restore_stations Restoring sta ff:ff:ff:ff:ff:ff [ 543.605375] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 543.605379] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 543.605383] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 543.605495] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 543.605516] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 543.605520] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 543.605523] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 0 addr 00:1f:3f:1e:b8:4a to uCode [ 543.605527] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 0 addr 00:1f:3f:1e:b8:4a [ 543.605531] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer 00:1f:3f:1e:b8:4a [ 543.605540] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 543.605545] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 543.605674] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 543.605822] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0 [ 543.605829] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 543.605832] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 543.605836] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 543.605981] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 543.606062] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 543.606066] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 543.606070] ieee80211 phy0: U iwl_sta_ucode_activate Added STA id 15 addr ff:ff:ff:ff:ff:ff to uCode [ 543.606073] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 15 addr ff:ff:ff:ff:ff:ff [ 543.606077] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer ff:ff:ff:ff:ff:ff [ 543.606086] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 543.606090] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 543.606218] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 543.608239] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 15 [ 543.608245] ieee80211 phy0: U iwl_restore_stations Restoring all known stations .... complete. [ 543.608250] ieee80211 phy0: U iwl_send_rxon_timing beacon interval 100 beacon timer 102016 beacon tim 0 [ 543.608254] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON_TIMING [ 543.608258] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON_TIMING [ 543.608577] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON_TIMING [ 543.608885] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_POWER_DBM_CMD [ 543.608890] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 543.609089] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 543.609119] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_QOS_PARAM [ 543.609123] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_QOS_PARAM [ 543.609223] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_QOS_PARAM [ 543.609269] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 543.609273] ieee80211 phy0: U _iwl_set_rxon_ht rxon flags 0x808025 operation mode :0x1 extension channel offset 0x0 [ 543.609277] ieee80211 phy0: U iwlagn_set_rxon_chain rx_chain=0x2806 active=2 idle=2 [ 543.609281] ieee80211 phy0: U iwl_full_rxon_required need full RXON - !iwl_is_associated_ctx(ctx) [ 543.609285] ieee80211 phy0: U iwlagn_commit_rxon Going to commit RXON [ 543.609286] * with RXON_FILTER_ASSOC_MSK [ 543.609287] * channel = 1 [ 543.609288] * bssid = 00:1f:3f:1e:b8:4a [ 543.609292] ieee80211 phy0: U iwl_send_rxon_timing beacon interval 100 beacon timer 57047 beacon tim 0 [ 543.609295] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON_TIMING [ 543.609299] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON_TIMING [ 543.609434] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON_TIMING [ 543.609616] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_QOS_PARAM [ 543.609620] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_QOS_PARAM [ 543.609730] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_QOS_PARAM [ 543.609758] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_RXON [ 543.609762] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_RXON [ 543.609986] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_RXON [ 543.610098] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_REMOVE_STA [ 543.610102] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_REMOVE_STA [ 543.610204] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_REMOVE_STA [ 543.610304] ieee80211 phy0: U iwl_send_remove_station REPLY_REMOVE_STA PASSED [ 543.610314] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 543.610317] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 543.610321] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 543.610539] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 543.610631] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 543.610635] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 543.610639] ieee80211 phy0: U iwl_sta_ucode_activate STA id 0 addr 00:1f:3f:1e:b8:4a already present in uCode (according to driver) [ 543.610643] ieee80211 phy0: U iwl_process_add_sta_resp Added station id 0 addr 00:1f:3f:1e:b8:4a [ 543.610646] ieee80211 phy0: U iwl_process_add_sta_resp Added station according to cmd buffer 00:1f:3f:1e:b8:4a [ 543.610655] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_LINK_QUALITY_CMD [ 543.610659] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 543.610790] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_LINK_QUALITY_CMD [ 543.610826] ieee80211 phy0: U iwl_send_lq_cmd init LQ command complete, clearing sta addition status for sta 0 [ 543.610832] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_TX_POWER_DBM_CMD [ 543.610836] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 543.611034] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_TX_POWER_DBM_CMD [ 543.629478] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 543.629484] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 543.629489] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 543.630952] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 543.631040] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 543.631048] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 543.631054] ieee80211 phy0: U iwl_sta_ucode_activate STA id 0 addr 00:1f:3f:1e:b8:4a already present in uCode (according to driver) [ 543.631062] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 0 addr 00:1f:3f:1e:b8:4a [ 543.631072] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer 00:1f:3f:1e:b8:4a [ 543.631395] ieee80211 phy0: U iwl_send_add_sta Adding sta 15 (ff:ff:ff:ff:ff:ff) synchronously [ 543.631399] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 543.631403] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 543.631531] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 543.631581] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 15 [ 543.631585] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 543.631589] ieee80211 phy0: U iwl_sta_ucode_activate STA id 15 addr ff:ff:ff:ff:ff:ff already present in uCode (according to driver) [ 543.631593] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 15 addr ff:ff:ff:ff:ff:ff [ 543.631596] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer ff:ff:ff:ff:ff:ff [ 544.128248] ieee80211 phy0: U iwl_send_add_sta Adding sta 0 (00:1f:3f:1e:b8:4a) synchronously [ 544.128259] ieee80211 phy0: U iwl_send_cmd_sync Attempting to send sync command REPLY_ADD_STA [ 544.128266] ieee80211 phy0: U iwl_send_cmd_sync Setting HCMD_ACTIVE for command REPLY_ADD_STA [ 544.128446] ieee80211 phy0: I iwl_tx_cmd_complete Clearing HCMD_ACTIVE for command REPLY_ADD_STA [ 544.128487] ieee80211 phy0: U iwl_process_add_sta_resp Processing response for adding station 0 [ 544.128494] ieee80211 phy0: U iwl_process_add_sta_resp REPLY_ADD_STA PASSED [ 544.128501] ieee80211 phy0: U iwl_sta_ucode_activate STA id 0 addr 00:1f:3f:1e:b8:4a already present in uCode (according to driver) [ 544.128509] ieee80211 phy0: U iwl_process_add_sta_resp Modified station id 0 addr 00:1f:3f:1e:b8:4a [ 544.128515] ieee80211 phy0: U iwl_process_add_sta_resp Modified station according to cmd buffer 00:1f:3f:1e:b8:4a [ 544.375064] CIFS VFS: Unexpected lookup error -112