Linux version 2.6.9-rc3-acpi (jesse@maggie) (gcc version 3.3.4 20040623 (Gentoo Linux 3.3.4-r1, ssp-3.3.2-2, pie-8.7.6)) #11 Sat Oct 9 10:12:02 EDT 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000013fd0000 (usable) BIOS-e820: 0000000013fd0000 - 0000000013fdf000 (ACPI data) BIOS-e820: 0000000013fdf000 - 0000000013fe0000 (ACPI NVS) BIOS-e820: 0000000013fe0000 - 0000000014000000 (reserved) BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved) 319MB LOWMEM available. On node 0 totalpages: 81872 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 77776 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI 2.2 present. ACPI: RSDP (v000 IBM ) @ 0x000fd6e0 ACPI: RSDT (v001 IBM TP600X 0x00000001 0x00000000) @ 0x13fd0000 ACPI: FADT (v001 IBM TP600X 0x00000001 0x00000000) @ 0x13fd0100 ACPI: BOOT (v001 IBM TP600X 0x00000001 0x00000000) @ 0x13fd0040 ACPI: DSDT (v001 IBM TP600X 0x00000106 MSFT 0x0100000c) @ 0x00000000 ACPI: PM-Timer IO Port: 0xef08 Built 1 zonelists Kernel command line: BOOT_IMAGE=Gentoo ro root=303 elevator=cfq resume=/dev/hda2 acpi=force pci=noacpi Initializing CPU#0 CPU 0 irqstacks, hard=c03aa000 soft=c03a9000 PID hash table entries: 2048 (order: 11, 32768 bytes) Detected 498.517 MHz processor. Using pmtmr for high-res timesource Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 321084k/327488k available (1813k kernel code, 5856k reserved, 761k data, 124k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 987.13 BogoMIPS (lpj=493568) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: Intel Pentium III (Coppermine) stepping 01 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. ACPI: IRQ9 SCI: Edge set to Level Trigger. NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfd880, last bus=7 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040816 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: Power Resource [PSIO] (on) ACPI: Embedded Controller [EC0] (gpe 9) ACPI: Power Resource [PFN0] (off) ACPI: Power Resource [PVID] (on) ACPI: Power Resource [PRSD] (off) ACPI: Power Resource [PDCK] (on) usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:07.0 Simple Boot Flag at 0x33 set to 0x1 IA-32 Microcode Update Driver: v1.14 Limiting direct PCI/PCI transfers. PCI: Found IRQ 11 for device 0000:01:00.0 PCI: Sharing IRQ 11 with 0000:00:02.0 PCI: Sharing IRQ 11 with 0000:00:06.0 neofb: mapped io at d4880000 Autodetected internal display Panel is a 1024x768 color TFT display neofb: mapped framebuffer at d4b00000 neofb v0.4.2: 4096kB VRAM, using 1024x768, 48.364kHz, 60Hz Console: switching to colour frame buffer device 128x48 fb0: MagicGraph 256ZX frame buffer device ACPI: AC Adapter [AC] (on-line) ACPI: Battery Slot [BAT0] (battery present) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID0] ACPI: Sleep Button (CM) [SLPB] ACPI: Fan [FN00] (off) ACPI: Fan [FN20] (off) ACPI: Fan [FN60] (off) ACPI: Fan [FN70] (off) ACPI: Processor [CPU0] (supports C1 C2 C3, 8 throttling states) ACPI: Thermal Zone [THM0] (43 C) ACPI: Thermal Zone [THM2] (38 C) ACPI: Thermal Zone [THM6] (27 C) ACPI: Thermal Zone [THM7] (27 C) serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 6 ports, IRQ sharing disabled acpi_serial_add: no iomem or port address in UAR1 _CRS Using cfq io scheduler Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PIIX4: IDE controller at PCI slot 0000:00:07.1 PIIX4: chipset revision 1 PIIX4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xfcf0-0xfcf7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xfcf8-0xfcff, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: IBM-DARA-218000, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: TOSHIBA CD-ROM XM-1902B, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 Probing IDE interface ide2... ide2: Wait for ready failed before probe ! Probing IDE interface ide3... ide3: Wait for ready failed before probe ! Probing IDE interface ide4... ide4: Wait for ready failed before probe ! Probing IDE interface ide5... ide5: Wait for ready failed before probe ! hda: max request size: 128KiB hda: 35426160 sectors (18138 MB) w/418KiB Cache, CHS=37488/15/63, UDMA(33) hda: cache flushes not supported hda: hda1 hda2 hda3 hdc: ATAPI 24X CD-ROM drive, 128kB Cache, DMA Uniform CD-ROM driver Revision: 3.20 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 input: PS/2 Generic Mouse on isa0060/serio1 NET: Registered protocol family 2 IP: routing cache hash table of 2048 buckets, 16Kbytes TCP: Hash tables configured (established 32768 bind 65536) NET: Registered protocol family 1 NET: Registered protocol family 17 ACPI: (supports S0 S1 hwregs-0169: *** Error: Missing Sleep State object S4 S5) ACPI wakeup devices: LID0 SLPB PCI0 UAR1 BAT0 USB0 EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 124k freed kjournald starting. Commit interval 5 seconds EXT3 FS on hda3, internal journal Linux Kernel Card Services options: [pci] [cardbus] [pm] PCI: Found IRQ 11 for device 0000:00:02.0 PCI: Sharing IRQ 11 with 0000:00:06.0 PCI: Sharing IRQ 11 with 0000:01:00.0 Yenta: CardBus bridge found at 0000:00:02.0 [1014:0130] Yenta: Enabling burst memory read transactions Yenta: Using INTVAL to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:00:02.0, mfunc 0x00001000, devctl 0x66 Yenta: ISA IRQ mask 0x04b8, PCI irq 11 Socket status: 30000006 PCI: Found IRQ 11 for device 0000:00:02.1 Yenta: CardBus bridge found at 0000:00:02.1 [1014:0130] Yenta: Using INTVAL to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:00:02.1, mfunc 0x00001000, devctl 0x66 Yenta: ISA IRQ mask 0x04b8, PCI irq 11 Socket status: 30000006 Linux agpgart interface v0.100 (c) Dave Jones PCI: Found IRQ 11 for device 0000:00:06.0 PCI: Sharing IRQ 11 with 0000:00:02.0 PCI: Sharing IRQ 11 with 0000:01:00.0 agpgart: Detected an Intel 440BX Chipset. agpgart: Maximum main memory to use for agp memory: 262M agpgart: AGP aperture is 64M @ 0x40000000 USB Universal Host Controller Interface driver v2.2 PCI: Found IRQ 11 for device 0000:00:07.2 uhci_hcd 0000:00:07.2: Intel Corp. 82371AB/EB/MB PIIX4 USB uhci_hcd 0000:00:07.2: irq 11, io base 00004000 uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected usb 1-1: new full speed USB device using address 2 drivers/usb/net/pegasus.c: v0.5.12 (2003/06/06):Pegasus/Pegasus II USB Ethernet driver drivers/usb/net/pegasus.c: intr interval will be changed from 1ms to 128ms drivers/usb/net/pegasus.c: setup Pegasus II specific registers eth0: Linksys USB USB100TX usbcore: registered new driver pegasus