rob@oak:~> uname -a Linux oak 2.6.24-rc3-mm1-pdcburst #3 SMP Sat Nov 24 14:42:12 GMT 2007 i686 athlon i386 GNU/Linux rob@oak:~> cat /proc/cmdline root=/dev/disk/by-label/OS-Root vga=0x317 resume=/dev/disk/by-label/OS-SWAP splash=silent Inspecting /boot/System.map-2.6.24-rc3-mm1-pdcburst Loaded 26223 symbols from /boot/System.map-2.6.24-rc3-mm1-pdcburst. Symbols match kernel version 2.6.24. No module symbols loaded - kernel modules not enabled. klogd 1.4.1, log source = ksyslog started. <5>Linux version 2.6.24-rc3-mm1-pdcburst (root@oak) (gcc version 4.2.1 (SUSE Linux)) #3 SMP Sat Nov 24 14:42:12 GMT 2007 <6>BIOS-provided physical RAM map: <4> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) <4> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) <4> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) <4> BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) <4> BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS) <4> BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data) <4> BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) <5>127MB HIGHMEM available. <5>896MB LOWMEM available. <6>found SMP MP-table at 000f4b00 <7>Entering add_active_range(0, 0, 262128) 0 entries of 256 used <7>sizeof(struct page) = 32 <4>Zone PFN ranges: <4> DMA 0 -> 4096 <4> Normal 4096 -> 229376 <4> HighMem 229376 -> 262128 <4>Movable zone start PFN for each node <4>early_node_map[1] active PFN ranges <4> 0: 0 -> 262128 <7>On node 0 totalpages: 262128 <7>Node 0 memmap at 0xC1000000 size 8388608 first pfn 0xC1000000 <7> DMA zone: 32 pages used for memmap <7> DMA zone: 0 pages reserved <7> DMA zone: 4064 pages, LIFO batch:0 <7> Normal zone: 1760 pages used for memmap <7> Normal zone: 223520 pages, LIFO batch:31 <7> HighMem zone: 255 pages used for memmap <7> HighMem zone: 32497 pages, LIFO batch:7 <7> Movable zone: 0 pages used for memmap <6>DMI 2.2 present. <4>ACPI: RSDP 000F6470, 0014 (r0 AMD2P ) <4>ACPI: RSDT 3FFF3000, 002C (r1 AMD2P AWRDACPI 42302E31 AWRD 0) <4>ACPI: FACP 3FFF3040, 0074 (r1 AMD2P AWRDACPI 42302E31 AWRD 0) <4>ACPI: DSDT 3FFF30C0, 33BC (r1 AMD2P AWRDACPI 1000 MSFT 100000C) <4>ACPI: FACS 3FFF0000, 0040 <4>ACPI: APIC 3FFF6480, 005C (r1 AMD2P AWRDACPI 42302E31 AWRD 0) <6>ACPI: PM-Timer IO Port: 0x608 <7>ACPI: Local APIC address 0xfee00000 <6>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) <4>Processor #0 6:8 APIC version 16 <6>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) <4>Processor #1 6:8 APIC version 16 <6>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) <4>IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 <6>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) <6>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) <7>ACPI: IRQ0 used by override. <7>ACPI: IRQ2 used by override. <7>ACPI: IRQ9 used by override. <4>Enabling APIC mode: Flat. Using 1 I/O APICs <6>Using ACPI (MADT) for SMP configuration information <4>Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000) <4>Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260081 <5>Kernel command line: root=/dev/disk/by-label/OS-Root vga=0x317 resume=/dev/disk/by-label/OS-SWAP splash=silent <7>mapped APIC to ffffb000 (fee00000) <7>mapped IOAPIC to ffffa000 (fec00000) <6>Enabling fast FPU save and restore... done. <6>Enabling unmasked SIMD FPU exception support... done. <6>Initializing CPU#0 <4>PID hash table entries: 4096 (order: 12, 16384 bytes) <4>Detected 1666.752 MHz processor. <4>Console: colour dummy device 80x25 <6>console [tty0] enabled <6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>Memory: 1028500k/1048512k available (1665k kernel code, 19348k reserved, 711k data, 188k init, 131008k highmem) <4>virtual kernel memory layout: <4> fixmap : 0xfff9b000 - 0xfffff000 ( 400 kB) <4> pkmap : 0xff800000 - 0xffc00000 (4096 kB) <4> vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) <4> lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) <4> .init : 0xc0359000 - 0xc0388000 ( 188 kB) <4> .data : 0xc02a07ad - 0xc0352574 ( 711 kB) <4> .text : 0xc0100000 - 0xc02a07ad (1665 kB) <4>Checking if this processor honours the WP bit even in supervisor mode... Ok. <4>Calibrating delay using timer specific routine.. 3337.18 BogoMIPS (lpj=6674360) <6>Security Framework initialized <4>Mount-cache hash table entries: 512 <7>CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000 00000000 <4>CPU: CLK_CTL MSR was 6003d22f. Reprogramming to 2003d22f <6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) <6>CPU: L2 Cache: 256K (64 bytes/line) <7>CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000420 00000000 00000000 00000000 00000000 <6>Intel machine check architecture supported. <6>Intel machine check reporting enabled on CPU#0. <4>Compat vDSO mapped to ffffe000. <6>Checking 'hlt' instruction... OK. <6>SMP alternatives: switching to UP code <6>ACPI: Core revision 20070126 <4>Parsing all Control Methods: <4>Table [DSDT](id 0001) - 421 Objects with 39 Devices 101 Methods 29 Regions <4> tbxface-0598 [00] tb_load_namespace : ACPI Tables successfully acquired <4>evxfevnt-0091 [00] enable : Transition to ACPI mode successful <4>CPU0: AMD Athlon(tm) MP 2000+ stepping 01 <6>SMP alternatives: switching to SMP code <4>Booting processor 1/1 eip 3000 <6>Initializing CPU#1 <4>Calibrating delay using timer specific routine.. 3333.78 BogoMIPS (lpj=6667561) <7>CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000 00000000 <4>CPU: CLK_CTL MSR was 6003d22f. Reprogramming to 2003d22f <6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) <6>CPU: L2 Cache: 256K (64 bytes/line) <7>CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000420 00000000 00000000 00000000 00000000 <6>Intel machine check architecture supported. <6>Intel machine check reporting enabled on CPU#1. <4>CPU1: AMD Athlon(tm) MP stepping 01 <6>Total of 2 processors activated (6670.96 BogoMIPS). <4>ENABLING IO-APIC IRQs <6>..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 <6>Brought up 2 CPUs <7>CPU0 attaching sched-domain: <7> domain 0: span 3 <7> groups: 1 2 <7>CPU1 attaching sched-domain: <7> domain 0: span 3 <7> groups: 2 1 <6>net_namespace: 64 bytes <6>NET: Registered protocol family 16 <6>ACPI: bus type pci registered <6>PCI: PCI BIOS revision 2.10 entry at 0xfb130, last bus=2 <6>PCI: Using configuration type 1 <6>Setting up standard PCI resources <4>mtrr: your CPUs had inconsistent fixed MTRR settings <6>mtrr: probably your BIOS does not setup all CPUs. <6>mtrr: corrected configuration. <4>evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 0F [_GPE] 2 regs on int 0x9 <4>evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 3 Wake, Enabled 1 Runtime GPEs in this block <7>ACPI: EC: Look up EC in DSDT <4>Completing Region/Field/Buffer/Package initialization:............................................................. <4>Initialized 26/29 Regions 5/5 Fields 18/18 Buffers 12/15 Packages (430 nodes) <4>Initializing Device/Processor/Thermal objects by executing _INI methods:. <4>Executed 1 _INI methods requiring 1 _STA executions (examined 43 objects) <6>ACPI: Interpreter enabled <6>ACPI: (supports S0 S1 S5) <6>ACPI: Using IOAPIC for interrupt routing <6>ACPI: PCI Root Bridge [PCI0] (0000:00) <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.OP2P._PRT] <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPP._PRT] <6>ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) <6>ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15) <6>ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. <6>ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15) <6>Linux Plug and Play Support v0.97 (c) Adam Belay <6>pnp: PnP ACPI init <6>ACPI: bus type pnp registered <6>pnp: PnP ACPI: found 15 devices <6>ACPI: ACPI bus type pnp unregistered <6>PnPBIOS: Disabled by ACPI PNP <6>PCI: Using ACPI for IRQ routing <6>PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report <4>ACPI: RTC can wake from S4 <6>system 00:00: iomem range 0xcc000-0xcffff has been reserved <6>system 00:00: iomem range 0xd5800-0xd7fff has been reserved <6>system 00:00: iomem range 0xf0000-0xfbfff could not be reserved <6>system 00:00: iomem range 0xfc000-0xfffff could not be reserved <6>system 00:00: iomem range 0x3fff0000-0x3fffffff could not be reserved <6>system 00:00: iomem range 0xffff0000-0xffffffff could not be reserved <6>system 00:00: iomem range 0x0-0x9ffff could not be reserved <6>system 00:00: iomem range 0x100000-0x3ffeffff could not be reserved <6>system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved <6>system 00:00: iomem range 0xfee00000-0xfee00fff could not be reserved <6>system 00:02: ioport range 0xb78-0xb7b has been reserved <6>system 00:02: ioport range 0xf78-0xf7b has been reserved <6>system 00:02: ioport range 0xa78-0xa7b has been reserved <6>system 00:02: ioport range 0xe78-0xe7b has been reserved <6>system 00:02: ioport range 0xbbc-0xbbf has been reserved <6>system 00:02: ioport range 0xfbc-0xfbf has been reserved <6>system 00:02: ioport range 0x4d0-0x4d1 has been reserved <6>PCI: Bridge: 0000:00:01.0 <6> IO window: disabled. <6> MEM window: f2000000-f4ffffff <6> PREFETCH window: f0000000-f1ffffff <6>PCI: Bridge: 0000:00:10.0 <6> IO window: c000-dfff <6> MEM window: f5000000-f6ffffff <6> PREFETCH window: disabled. <6>NET: Registered protocol family 2 <6>Time: acpi_pm clocksource has been installed. <6>Switched to NOHz mode on CPU #0 <6>Switched to NOHz mode on CPU #1 <6>IP route cache hash table entries: 32768 (order: 5, 131072 bytes) <6>TCP established hash table entries: 131072 (order: 8, 1048576 bytes) <6>TCP bind hash table entries: 65536 (order: 7, 524288 bytes) <6>TCP: Hash tables configured (established 131072 bind 65536) <6>TCP reno registered <6>Unpacking initramfs... done <6>Freeing initrd memory: 7203k freed <6>Machine check exception polling timer started. <6>audit: initializing netlink socket (disabled) <5>audit(1196008360.856:1): initialized <4>highmem bounce pool size: 64 pages <4>Total HugeTLB memory allocated, 0 <5>VFS: Disk quotas dquot_6.5.1 <4>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>io scheduler noop registered <6>io scheduler anticipatory registered <6>io scheduler deadline registered <6>io scheduler cfq registered (default) <4>BIOS failed to enable PCI standards compliance, fixing this error. <7>Boot video device is 0000:01:05.0 <4>PCI: Firmware left 0000:02:09.0 e100 interrupts enabled, disabling <6>vesafb: framebuffer at 0xf0000000, mapped to 0xF8880000, using 3072k, total 32768k <6>vesafb: mode is 1024x768x16, linelength=2048, pages=9 <6>vesafb: protected mode interface info at c000:7d60 <6>vesafb: pmi: set display start = C00C7DF2, set palette = C00C7E5E <6>vesafb: pmi: ports = 3de 3df <6>vesafb: scrolling: redraw <6>vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 <4>Console: switching to colour frame buffer device 128x48 <6>fb0: VESA VGA frame buffer device <6>isapnp: Scanning for PnP cards... <6>isapnp: No Plug & Play device found <6>Real Time Clock Driver v1.12ac <6>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled <6>serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A <6>serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A <6>00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A <6>00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A <6>Floppy drive(s): fd0 is 1.44M <6>FDC 0 is a post-1991 82077 <6>PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 <6>serio: i8042 KBD port at 0x60,0x64 irq 1 <6>serio: i8042 AUX port at 0x60,0x64 irq 12 <6>mice: PS/2 mouse device common for all mice <6>input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 <6>input: PC Speaker as /devices/platform/pcspkr/input/input1 <6>input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input2 <6>cpuidle: using governor ladder <6>cpuidle: using governor menu <6>NET: Registered protocol family 1 <4>Using IPI No-Shortcut mode <4>registered taskstats version 1 <6>Freeing unused kernel memory: 188k freed <5>SCSI subsystem initialized <7>libata version 3.00 loaded. <7>pata_amd 0000:00:07.1: version 0.3.10 <6>scsi0 : pata_amd <6>scsi1 : pata_amd <6>ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xe000 irq 14 <6>ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xe008 irq 15 <6>ata1.00: ATA-6: ST360015A, 3.53, max UDMA/100 <6>ata1.00: 117231408 sectors, multi 16: LBA <6>ata1.00: configured for UDMA/100 <6>ata2.00: ATA-6: ST360015A, 3.53, max UDMA/100 <6>ata2.00: 117231408 sectors, multi 16: LBA <6>ata2.00: configured for UDMA/100 <5>scsi 0:0:0:0: Direct-Access ATA ST360015A 3.53 PQ: 0 ANSI: 5 <5>scsi 1:0:0:0: Direct-Access ATA ST360015A 3.53 PQ: 0 ANSI: 5 <6>ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 16 (level, low) -> IRQ 16 <6>scsi2 : pata_pdc202xx_old <6>scsi3 : pata_pdc202xx_old <6>ata3: PATA max UDMA/100 cmd 0xc000 ctl 0xc400 bmdma 0xd000 irq 16 <6>ata4: PATA max UDMA/100 cmd 0xc800 ctl 0xcc00 bmdma 0xd008 irq 16 <5>sd 0:0:0:0: [sda] 117231408 512-byte hardware sectors (60022 MB) <5>sd 0:0:0:0: [sda] Write Protect is off <7>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 0:0:0:0: [sda] 117231408 512-byte hardware sectors (60022 MB) <5>sd 0:0:0:0: [sda] Write Protect is off <7>sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6> sda:<6>usbcore: registered new interface driver usbfs <6>usbcore: registered new interface driver hub <4> sda1 sda2 sda3 < sda5<6>usbcore: registered new device driver usb <4> sda6 sda7<7>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver <4> sda8<6>ACPI: PCI Interrupt 0000:02:00.0[D] -> GSI 19 (level, low) -> IRQ 17 <4> sda9 sda10 sda11 > <6>ohci_hcd 0000:02:00.0: OHCI Host Controller <6>ohci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 1 <6>ohci_hcd 0000:02:00.0: irq 17, io mem 0xf6041000 <5>sd 0:0:0:0: [sda] Attached SCSI disk <6>usb usb1: configuration #1 chosen from 1 choice <6>hub 1-0:1.0: USB hub found <6>hub 1-0:1.0: 4 ports detected <5>sd 1:0:0:0: [sdb] 117231408 512-byte hardware sectors (60022 MB) <5>sd 1:0:0:0: [sdb] Write Protect is off <7>sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6>usb usb1: new device found, idVendor=0000, idProduct=0000 <6>usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb1: Product: OHCI Host Controller <6>usb usb1: Manufacturer: Linux 2.6.24-rc3-mm1-pdcburst ohci_hcd <6>usb usb1: SerialNumber: 0000:02:00.0 <5>sd 1:0:0:0: [sdb] 117231408 512-byte hardware sectors (60022 MB) <5>sd 1:0:0:0: [sdb] Write Protect is off <7>sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6> sdb: sdb1 sdb2 sdb3 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 > sdb4 <5>sd 1:0:0:0: [sdb] Attached SCSI disk <5>ReiserFS: sda5: found reiserfs format "3.6" with standard journal <5>ReiserFS: sda5: using ordered data mode <5>ReiserFS: sda5: journal params: device sda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 <5>ReiserFS: sda5: checking transaction log (sda5) <5>ReiserFS: sda5: Using r5 hash to sort names <5>sd 0:0:0:0: Attached scsi generic sg0 type 0 <5>sd 1:0:0:0: Attached scsi generic sg1 type 0 <6>input: Power Button (FF) as /devices/virtual/input/input3 <6>e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI <6>e100: Copyright(c) 1999-2006 Intel Corporation <6>ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 17 (level, low) -> IRQ 18 <6>ACPI: Power Button (FF) [PWRF] <6>input: Sleep Button (FF) as /devices/virtual/input/input4 <4>rtc_cmos: probe of 00:04 failed with error -16 <6>e100: eth0: e100_probe: addr 0xf6040000, irq 18, MAC addr 00:10:dc:fc:12:99 <6>parport_pc 00:0a: reported by Plug and Play ACPI <6>parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] <6>ACPI: Sleep Button (FF) [SLPF] <6>input: Power Button (CM) as /devices/virtual/input/input5 <6>AMD768 RNG detected <6>ACPI: Power Button (CM) [PWRB] <6>input: Sleep Button (CM) as /devices/virtual/input/input6 <6>gameport: NS558 PnP Gameport is pnp00:0d/gameport0, io 0x201, speed 59659kHz <6>ACPI: Sleep Button (CM) [SLPB] <6>Linux agpgart interface v0.102 <6>agpgart: Detected AMD 760MP chipset <6>agpgart: AGP aperture is 128M @ 0xe8000000 <6>ACPI: PCI Interrupt 0000:00:07.5[B] -> GSI 17 (level, low) -> IRQ 18 <6>intel8x0_measure_ac97_clock: measured 50329 usecs <6>intel8x0: clocking to 48000 <6>Adding 976712k swap on /dev/sda10. Priority:2 extents:1 across:976712k <6>Adding 1952960k swap on /dev/sdb10. Priority:4 extents:1 across:1952960k <6>loop: module loaded <5>ReiserFS: sda9: found reiserfs format "3.6" with standard journal <5>ReiserFS: sda9: using ordered data mode <5>ReiserFS: sda9: journal params: device sda9, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 <5>ReiserFS: sda9: checking transaction log (sda9) <5>ReiserFS: sda9: Using r5 hash to sort names <5>ReiserFS: sda7: found reiserfs format "3.6" with standard journal <5>ReiserFS: sda7: using ordered data mode <5>ReiserFS: sda7: journal params: device sda7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 <5>ReiserFS: sda7: checking transaction log (sda7) <5>ReiserFS: sda7: Using r5 hash to sort names <6>kjournald starting. Commit interval 5 seconds <6>EXT3 FS on sda8, internal journal <6>EXT3-fs: mounted filesystem with writeback data mode. <6>kjournald starting. Commit interval 5 seconds <6>EXT3 FS on sda2, internal journal <6>EXT3-fs: mounted filesystem with writeback data mode. <5>ReiserFS: sda6: found reiserfs format "3.6" with standard journal <5>ReiserFS: sda6: using ordered data mode <5>ReiserFS: sda6: journal params: device sda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 <5>ReiserFS: sda6: checking transaction log (sda6) <5>ReiserFS: sda6: Using r5 hash to sort names <6>kjournald starting. Commit interval 5 seconds <6>EXT3 FS on sdb9, internal journal <6>EXT3-fs: mounted filesystem with writeback data mode. Kernel logging (ksyslog) stopped. Kernel log daemon terminating. Boot logging started on /dev/tty1(/dev/console) at Sun Nov 25 16:32:42 2007 FATAL: Module edd not found. Creating device nodes with udev Trying manual resume from /dev/disk/by-label/OS-SWAP Trying manual resume from /dev/disk/by-label/OS-SWAP Waiting for device /dev/disk/by-label/OS-Root to appear: ok showconsole: Warning: the ioctl TIOCGDEV is not known by the kernel fsck 1.40.2 (12-Jul-2007) [/sbin/fsck.reiserfs (1) -- /] fsck.reiserfs -a /dev/disk/by-label/OS-Root Reiserfs super block in block 16 on 0x805 of format 3.6 with standard journal Blocks (total/free): 134304/37300 by 4096 bytes Filesystem is clean Replaying journal: Replaying journal: Done. Reiserfs journal '/dev/disk/by-label/OS-Root' in blocks [18..8211]: 0 transactions replayed Checking internal tree.. ^H\^H|^H/^H-^H\^H|^H/^H-^H\^H|^H/^H-^H\^Hfinished fsck succeeded. Mounting root device read-write. Mounting root /dev/disk/by-label/OS-Root Boot logging started on /dev/tty1(/dev/console) at Sun Nov 25 16:33:00 2007 Master Resource Control: previous runlevel: N, switching to runlevel: 5 Initializing random number generatordone startproc: execve (/sbin/resmgrd) [ /sbin/resmgrd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 resume=/dev/disk/by-label/OS-SWAP PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/sbin/resmgrd ] startproc: execve (/usr/sbin/irqbalance) [ /usr/sbin/irqbalance ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 resume=/dev/disk/by-label/OS-SWAP PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/usr/sbin/irqbalance ] Starting irqbalance done Starting resource managerdone startproc: execve (/sbin/acpid) [ /sbin/acpid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 resume=/dev/disk/by-label/OS-SWAP PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/sbin/acpid ] acpid: starting up startproc: execve (/sbin/syslog-ng) [ /sbin/syslog-ng -a /var/lib/dhcp/dev/log -a /var/lib/named/dev/log ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 SPLASHCFG= PWD=/ resume=/dev/disk/by-label/OS-SWAP PREVLEVEL=N LINES=48 SHLVL=2 HOME=/ SPLASH=no splash=silent ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/sbin/syslog-ng ] Starting acpid done startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -x -x ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 SPLASHCFG= PWD=/ resume=/dev/disk/by-label/OS-SWAP PREVLEVEL=N LINES=48 SHLVL=2 HOME=/ SPLASH=no splash=silent ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/sbin/klogd ] Starting syslog services.done Starting D-Bus daemonUnknown username "gdm" in message bus configuration file done startproc: execve (/usr/sbin/console-kit-daemon) [ /usr/sbin/console-kit-daemon ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 resume=/dev/disk/by-label/OS-SWAP PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/usr/sbin/console-kit-daemon ] Starting ConsoleKitdone startproc: execve (/usr/sbin/hald) [ /usr/sbin/hald --daemon=yes ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 resume=/dev/disk/by-label/OS-SWAP PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/usr/sbin/hald ] Starting HAL daemondone Loading CPUFreq modules (CPUFreq not supported) Loading keymap i386/qwerty/uk.map.gz doneLoading compose table latin1.adddone Start Unicode mode doneLoading console font lat9w-16.psfu -m trivial G0:loadable doneStarting service kdmstartproc: execve (/opt/kde3/bin/kdm) [ /opt/kde3/bin/kdm ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs TERM=linux SHELL=/bin/sh ROOTFS_FSCK=0 INIT_VERSION=sysvinit-2.86 KDEROOTHOME=/root/.kdm REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 SPLASHCFG= PWD=/ resume=/dev/disk/by-label/OS-SWAP LANG=en_GB.UTF-8 PREVLEVEL=N LINES=48 QT_SYSTEM_DIR=/usr/share/desktop-data SHLVL=2 HOME=/ XCURSOR_THEME=crystalwhite WINDOWMANAGER=/usr/bin/kde SPLASH=no splash=silent ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/opt/kde3/bin/kdm ] done checkproc: /opt/kde3/bin/kdm 2590 Setting up network interfaces: lo lo IP address: 127.0.0.1/8 Checking for network time protocol daemon (NTPD): unused done eth0 device: Intel Corporation 82557/8/9 Ethernet Pro 100 (rev 10) eth0 IP address: 10.5.5.1/8 Checking for network time protocol daemon (NTPD): unused doneSetting up service network . . . . . . . . . . . . . . . .done checkproc: /opt/kde3/bin/kdm 2590 startproc: execve (/sbin/auditd) [ /sbin/auditd -s disable ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 resume=/dev/disk/by-label/OS-SWAP PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/sbin/auditd ] Starting auditd done Starting Avahi daemonstartproc: execve (/usr/sbin/avahi-daemon) [ /usr/sbin/avahi-daemon -D ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 resume=/dev/disk/by-label/OS-SWAP PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/usr/sbin/avahi-daemon ] .done startproc: execve (/usr/sbin/avahi-dnsconfd) [ /usr/sbin/avahi-dnsconfd -D ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 resume=/dev/disk/by-label/OS-SWAP PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/usr/sbin/avahi-dnsconfd ] Starting Avahi DNS Configuration daemondone startproc: execve (/usr/sbin/ntpd) [ /usr/sbin/ntpd -p /var/run/ntp/ntpd.pid -u ntp ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 resume=/dev/disk/by-label/OS-SWAP PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/usr/sbin/ntpd ] Try to get initial date and time via NTP from ntp2.ntli.netdone Starting network time protocol daemon (NTPD)done startproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 resume=/dev/disk/by-label/OS-SWAP PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/usr/sbin/nscd ] Starting Name Service Cache Daemondone startproc: execve (/sbin/portmap) [ /sbin/portmap ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 resume=/dev/disk/by-label/OS-SWAP PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/sbin/portmap ] Starting RPC portmap daemondone startproc: execve (/usr/sbin/cupsd) [ /usr/sbin/cupsd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 resume=/dev/disk/by-label/OS-SWAP PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/usr/sbin/cupsd ] Starting cupsddone Starting mail service (Postfix)done startproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 resume=/dev/disk/by-label/OS-SWAP PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/usr/sbin/cron ] Starting CRON daemondone startproc: execve (/usr/sbin/powersaved) [ /usr/sbin/powersaved -d -f /var/run/acpid.socket -v 3 ], [ HOME=/ PATH=/bin:/sbin:/usr/bin:/usr/sbin SHELL=/bin/sh RUNLEVEL=5 PREVLEVEL=N DAEMON=/usr/sbin/powersaved ] Starting powersaved: done Starting smartd startproc: execve (/usr/sbin/smartd) [ /usr/sbin/smartd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 resume=/dev/disk/by-label/OS-SWAP PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/usr/sbin/smartd ] done startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=128 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x317 RUNLEVEL=5 resume=/dev/disk/by-label/OS-SWAP PWD=/ SPLASHCFG= PREVLEVEL=N LINES=48 HOME=/ SHLVL=2 splash=silent SPLASH=no ROOTFS_BLKDEV=/dev/disk/by-label/OS-Root _=/sbin/startproc DAEMON=/usr/sbin/sshd ] Starting SSH daemondone done Master Resource Control: runlevel 5 has been reached Skipped services in runlevel 5: splash killproc: kill(2050,3)