Most recent kernel where this bug did not occur: unknown Distribution: Gentoo Hardware Environment: MSI ms-7191 (ati rs482m4 with sb450) athlon64-3200+ Software Environment: Problem Description: /proc/acpi does not exist, even though acpi is enabled. This could be related to the buggy DSDT of this board. There is a 0x03 character in a ACPI name (as reported in dmesg below). Steps to reproduce: boot with noapic. (Without noapic I cannot boot if acpi is enabled in my BIOS.) output of "dmesg|grep -i acpi": BIOS-e820: 000000003bfd0000 - 000000003bfde000 (ACPI data) BIOS-e820: 000000003bfde000 - 000000003c000000 (ACPI NVS) ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000f96e0 ACPI: RSDT (v001 A M I OEMRSDT 0x10000514 MSFT 0x00000097) @ 0x000000003bfd0000 ACPI: FADT (v002 A M I OEMFACP 0x10000514 MSFT 0x00000097) @ 0x000000003bfd0200 ACPI: MADT (v001 A M I OEMAPIC 0x10000514 MSFT 0x00000097) @ 0x000000003bfd0390 ACPI: MCFG (v001 A M I OEMMCFG 0x10000514 MSFT 0x00000097) @ 0x000000003bfd03f0 ACPI: OEMB (v001 A M I AMI_OEM 0x10000514 MSFT 0x00000097) @ 0x000000003bfde040 ACPI: DSDT (v001 1ABZR 1ABZRB49 0x00000b49 INTL 0x02002026) @ 0x0000000000000000 ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) ACPI: Skipping IOAPIC probe due to 'noapic' option. Using ACPI for processor (LAPIC) configuration information tbxface-0109 [02] load_tables : ACPI Tables successfully acquired ACPI Error (nssearch-0311): Bad character in ACPI Name: 43035350 [20060127] ACPI Error (dswload-0305): [0x43035350] (NON-ASCII) Namespace lookup failure, AE_BAD_CHARACTER ACPI Exception (psloop-0281): AE_BAD_CHARACTER, During name lookup/catalog [20060127] ACPI Exception (tbxface-0115): AE_BAD_CHARACTER, Could not load namespace [20060127] ACPI Exception (tbxface-0122): AE_BAD_CHARACTER, Could not load tables [20060127] ACPI: Unable to load the System Description Tables ACPI: Subsystem revision 20060127 ACPI: Interpreter disabled. my full dmesg output: Bootdata ok (command line is root=/dev/sda3 vga=0x31B video=vesafb:ywrap,mtrr noapic) Linux version 2.6.16.14 (root@hakbak) (gcc version 4.1.0 (Gentoo 4.1.0)) #1 PREEMPT Tue May 9 12:43:53 CEST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003bfd0000 (usable) BIOS-e820: 000000003bfd0000 - 000000003bfde000 (ACPI data) BIOS-e820: 000000003bfde000 - 000000003c000000 (ACPI NVS) BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000f96e0 ACPI: RSDT (v001 A M I OEMRSDT 0x10000514 MSFT 0x00000097) @ 0x000000003bfd0000 ACPI: FADT (v002 A M I OEMFACP 0x10000514 MSFT 0x00000097) @ 0x000000003bfd0200 ACPI: MADT (v001 A M I OEMAPIC 0x10000514 MSFT 0x00000097) @ 0x000000003bfd0390 ACPI: MCFG (v001 A M I OEMMCFG 0x10000514 MSFT 0x00000097) @ 0x000000003bfd03f0 ACPI: OEMB (v001 A M I AMI_OEM 0x10000514 MSFT 0x00000097) @ 0x000000003bfde040 ACPI: DSDT (v001 1ABZR 1ABZRB49 0x00000b49 INTL 0x02002026) @ 0x0000000000000000 On node 0 totalpages: 241303 DMA zone: 2990 pages, LIFO batch:0 DMA32 zone: 238313 pages, LIFO batch:31 Normal zone: 0 pages, LIFO batch:0 HighMem zone: 0 pages, LIFO batch:0 ATI board detected. Disabling timer routing over 8254. ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:15 APIC version 16 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) ACPI: Skipping IOAPIC probe due to 'noapic' option. Using ACPI for processor (LAPIC) configuration information Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: ATI Product ID: RS480 APIC at: 0xFEE00000 I/O APIC #1 Version 33 at 0xFEC00000. Setting APIC routing to flat Processors: 1 Allocating PCI resources starting at 40000000 (gap: 3c000000:c3780000) Checking aperture... CPU 0: aperture @ 37ee000000 size 32 MB Aperture from northbridge cpu 0 too small (32 MB) No AGP bridge found Built 1 zonelists Kernel command line: root=/dev/sda3 vga=0x31B video=vesafb:ywrap,mtrr noapic Initializing CPU#0 PID hash table entries: 4096 (order: 12, 131072 bytes) time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer. time.c: Detected 1994.300 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Memory: 963232k/982848k available (2431k kernel code, 18940k reserved, 902k data, 184k init) Calibrating delay using timer specific routine.. 3993.98 BogoMIPS (lpj=1996990) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 02 tbxface-0109 [02] load_tables : ACPI Tables successfully acquired ACPI Error (nssearch-0311): Bad character in ACPI Name: 43035350 [20060127] ACPI Error (dswload-0305): [0x43035350] (NON-ASCII) Namespace lookup failure, AE_BAD_CHARACTER ACPI Exception (psloop-0281): AE_BAD_CHARACTER, During name lookup/catalog [20060127] ACPI Exception (tbxface-0115): AE_BAD_CHARACTER, Could not load namespace [20060127] ACPI Exception (tbxface-0122): AE_BAD_CHARACTER, Could not load tables [20060127] ACPI: Unable to load the System Description Tables Using local APIC timer interrupts. result 12464392 Detected 12.464 MHz APIC timer. testing NMI watchdog ... OK. DMI 2.3 present. NET: Registered protocol family 16 PCI: Using configuration type 1 PCI: Using MMCONFIG at e0000000 ACPI: Subsystem revision 20060127 ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1 Boot video device is 0000:01:05.0 PCI: Transparent bridge - 0000:00:14.4 PCI: Using IRQ router default [1002/4377] at 0000:00:14.3 PCI-DMA: Disabling IOMMU. PCI: Bridge: 0000:00:01.0 IO window: d000-dfff MEM window: fea00000-feafffff PREFETCH window: f0000000-f7ffffff PCI: Bridge: 0000:00:14.4 IO window: e000-efff MEM window: feb00000-febfffff PREFETCH window: 40000000-400fffff IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ Total HugeTLB memory allocated, 0 io scheduler noop registered io scheduler deadline registered (default) io scheduler cfq registered vesafb: framebuffer at 0xf0000000, mapped to 0xffffc20010100000, using 7680k, total 65536k vesafb: mode is 1280x1024x24, linelength=3840, pages=16 vesafb: scrolling: redraw vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 Console: switching to colour frame buffer device 160x64 fb0: VESA VGA frame buffer device Real Time Clock Driver v1.12ac Linux agpgart interface v0.101 (c) Dave Jones PNP: No PS/2 controller found. Probing ports directly. serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 isa bounce pool size: 16 pages RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) 8139too Fast Ethernet driver 0.9.27 eth0: RealTek RTL8139 at 0xffffc20000002c00, 00:13:d3:ab:7a:d0, IRQ 3 eth0: Identified 8139 chip type 'RTL-8100B/8139D' Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ATIIXP: IDE controller at PCI slot 0000:00:14.1 ATIIXP: chipset revision 128 ATIIXP: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio ATIIXP: simplex device: DMA disabled ide1: ATIIXP Bus-Master DMA disabled (BIOS) Probing IDE interface ide0... hda: TSSTcorpCD/DVDW SH-W162C, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... Probing IDE interface ide1... hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 libata version 1.20 loaded. sata_sil 0000:00:11.0: version 0.9 ata1: SATA max UDMA/100 cmd 0xFFFFC20000004C80 ctl 0xFFFFC20000004C8A bmdma 0xFFFFC20000004C00 irq 11 ata2: SATA max UDMA/100 cmd 0xFFFFC20000004CC0 ctl 0xFFFFC20000004CCA bmdma 0xFFFFC20000004C08 irq 11 ata1: SATA link up 1.5 Gbps (SStatus 113) ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e01 87:4663 88:407f ata1: dev 0 ATA-7, max UDMA/133, 490234752 sectors: LBA48 ata1: dev 0 configured for UDMA/100 scsi0 : sata_sil ata2: SATA link down (SStatus 0) scsi1 : sata_sil Vendor: ATA Model: Maxtor 6L250S0 Rev: BANC Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sda4 < sda5 > sd 0:0:0:0: Attached scsi disk sda ieee1394: raw1394: /dev/raw1394 device initialized usbmon: debugfs is not available ehci_hcd 0000:00:13.2: EHCI Host Controller ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:13.2: irq 5, io mem 0xfe9f8000 ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd 0000:00:13.0: OHCI Host Controller ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:13.0: irq 5, io mem 0xfe9fa000 usb usb2: configuration #1 chosen from 1 choice Losing some ticks... checking if CPU frequency changed. hub 2-0:1.0: USB hub foun]d hub 2-0:1.0: 4 ports detected usb 1-4: new high speed USB device using ehci_hcd and address 2 ohci_hcd 0000:00:13.1: OHCI Host Controller ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:13.1: irq 5, io mem 0xfe9f9000 usb 1-4: configuration #1 chosen from 1 choice hub 1-4:1.0: USB hub found hub 1-4:1.0: 4 ports detected usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 4 ports detected Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input0 logips2pp: Detected unknown logitech mouse model 1 input: PS/2 Logitech Mouse as /class/input/input1 input: PC Speaker as /class/input/input2 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 6, 262144 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 184k freed kjournald starting. Commit interval 5 seconds hda_codec: Unknown model for ALC880, trying auto-probe from BIOS... Adding 1959920k swap on /dev/sda2. Priority:-1 extents:1 across:1959920k EXT3 FS on sda3, internal journal eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 [drm] Initialized drm 1.0.1 20051102 spurious 8259A interrupt: IRQ7.
I've tried booting with the following patch: *** utmisc.c Fri May 5 02:03:45 2006 --- patched_utmisc.c Tue May 9 13:23:56 2006 *************** *** 493,498 **** --- 493,499 ---- name_ptr++; if (!((character == '_') || + (character == 0x03) || (character >= 'A' && character <= 'Z') || (character >= '0' && character <= '9'))) { return (FALSE); but when my startup scripts are running dhcpcd I get something like "interrupt #15 disabled" and then my box doesn't make any progress, although the keyboard is working a bit. CTRL_ALT_DEL doesn't work though. I've been unable to find any log of booting this patched kernel :( so I don't know what's going on.
ACPI is indeed disabled because it found a non-ASCII character in your DSDT. > ACPI: Subsystem revision 20060127 We have a couple of fixes floating around for this. Please try the simple hack in the 22nd comment here: https://bugzilla.novell.com/show_bug.cgi?id=147621 This may also be fixed upstream. Please try the latest -mm kernel, or the latest ACPI patch here: http://ftp.kernel.org/pub/linux/kernel/people/lenb/acpi/patches/test/2.6.16/
I tried the simple patch and it produces the same effect as my own. Which means it seems to hang when doing dhcpcd (as reported earlier), but really it is just failing. I was copying some lines and all of a sudden dhcpcd timed out and kdm came up. This time i've found the log: May 18 13:03:36 [kernel] Bootdata ok (command line is root=/dev/sda3 vga=0x31B video=vesafb:ywrap,mtrr noapic) May 18 13:03:36 [kernel] Linux version 2.6.16.14 (marijn@hakbak) (gcc version 4.1.0 (Gentoo 4.1.0)) #4 PREEMPT Thu May 18 12:27:43 CEST 2006 May 18 13:03:36 [kernel] BIOS-provided physical RAM map: May 18 13:03:36 [kernel] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) May 18 13:03:36 [kernel] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) May 18 13:03:36 [kernel] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) May 18 13:03:36 [kernel] BIOS-e820: 0000000000100000 - 000000003bfd0000 (usable) May 18 13:03:36 [kernel] BIOS-e820: 000000003bfd0000 - 000000003bfde000 (ACPI data) May 18 13:03:36 [kernel] BIOS-e820: 000000003bfde000 - 000000003c000000 (ACPI NVS) May 18 13:03:36 [kernel] BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) May 18 13:03:36 [kernel] ACPI: Scanning for RSDP signature... <6>ACPI: done May 18 13:03:36 [kernel] ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000f96e0 May 18 13:03:36 [kernel] ACPI: RSDT (v001 A M I OEMRSDT 0x10000514 MSFT 0x00000097) @ 0x000000003bfd0000 May 18 13:03:36 [kernel] ACPI: FADT (v002 A M I OEMFACP 0x10000514 MSFT 0x00000097) @ 0x000000003bfd0200 May 18 13:03:36 [kernel] ACPI: MADT (v001 A M I OEMAPIC 0x10000514 MSFT 0x00000097) @ 0x000000003bfd0390 May 18 13:03:36 [kernel] ACPI: MCFG (v001 A M I OEMMCFG 0x10000514 MSFT 0x00000097) @ 0x000000003bfd03f0 May 18 13:03:36 [kernel] ACPI: OEMB (v001 A M I AMI_OEM 0x10000514 MSFT 0x00000097) @ 0x000000003bfde040 May 18 13:03:36 [kernel] ACPI: DSDT (v001 1ABZR 1ABZRB49 0x00000b49 INTL 0x02002026) @ 0x0000000000000000 May 18 13:03:36 [kernel] On node 0 totalpages: 241303 May 18 13:03:36 [kernel] DMA zone: 2990 pages, LIFO batch:0 May 18 13:03:36 [kernel] DMA32 zone: 238313 pages, LIFO batch:31 May 18 13:03:36 [kernel] Normal zone: 0 pages, LIFO batch:0 May 18 13:03:36 [kernel] HighMem zone: 0 pages, LIFO batch:0 May 18 13:03:36 [kernel] ATI board detected. Disabling timer routing over 8254. May 18 13:03:36 [kernel] ACPI: PM-Timer IO Port: 0x808 May 18 13:03:36 [kernel] ACPI: Local APIC address 0xfee00000 May 18 13:03:36 [kernel] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) May 18 13:03:36 [kernel] Processor #0 15:15 APIC version 16 May 18 13:03:36 [kernel] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) May 18 13:03:36 [kernel] ACPI: Skipping IOAPIC probe due to 'noapic' option. May 18 13:03:36 [kernel] Using ACPI for processor (LAPIC) configuration information May 18 13:03:36 [kernel] Intel MultiProcessor Specification v1.4 May 18 13:03:36 [kernel] Virtual Wire compatibility mode. May 18 13:03:36 [kernel] OEM ID: ATI Product ID: RS480 APIC at: 0xFEE00000 May 18 13:03:36 [kernel] I/O APIC #1 Version 33 at 0xFEC00000. May 18 13:03:36 [kernel] Setting APIC routing to flat May 18 13:03:36 [kernel] Processors: 1 May 18 13:03:36 [kernel] Allocating PCI resources starting at 40000000 (gap: 3c000000:c3780000) May 18 13:03:36 [kernel] Checking aperture... May 18 13:03:36 [kernel] CPU 0: aperture @ 77ee000000 size 32 MB May 18 13:03:36 [kernel] Aperture from northbridge cpu 0 too small (32 MB) May 18 13:03:36 [kernel] No AGP bridge found May 18 13:03:36 [kernel] Built 1 zonelists May 18 13:03:36 [kernel] Kernel command line: root=/dev/sda3 vga=0x31B video=vesafb:ywrap,mtrr noapic May 18 13:03:36 [kernel] Initializing CPU#0 May 18 13:03:36 [kernel] PID hash table entries: 4096 (order: 12, 131072 bytes) May 18 13:03:36 [kernel] time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer. May 18 13:03:36 [kernel] time.c: Detected 1994.240 MHz processor. May 18 13:03:36 [kernel] Console: colour dummy device 80x25 May 18 13:03:36 [kernel] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) May 18 13:03:36 [kernel] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) May 18 13:03:36 [kernel] Memory: 963232k/982848k available (2431k kernel code, 18940k reserved, 902k data, 184k init) May 18 13:03:36 [kernel] Calibrating delay using timer specific routine.. 3993.88 BogoMIPS (lpj=1996944) May 18 13:03:36 [kernel] Mount-cache hash table entries: 256 May 18 13:03:36 [kernel] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) May 18 13:03:36 [kernel] CPU: L2 Cache: 512K (64 bytes/line) May 18 13:03:36 [kernel] CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 02 May 18 13:03:36 [kernel] tbxface-0109 [02] load_tables : ACPI Tables successfully acquired May 18 13:03:36 [kernel] ACPI Error (nssearch-0311): Bad character in ACPI Name: 43035350 [20060127] - Last output repeated twice - May 18 13:03:36 [kernel] Parsing all Control Methods: May 18 13:03:36 [kernel] Table [DSDT](id 0005) - 556 Objects with 53 Devices 164 Methods 12 Regions May 18 13:03:36 [kernel] ACPI Namespace successfully loaded at root ffffffff80467aa0 May 18 13:03:36 [kernel] ACPI: setting ELCR to 0200 (from 8e28) May 18 13:03:36 [kernel] evxfevnt-0091 [03] enable : Transition to ACPI mode successful May 18 13:03:36 [kernel] Using local APIC timer interrupts. May 18 13:03:36 [kernel] result 12464015 May 18 13:03:36 [kernel] Detected 12.464 MHz APIC timer. May 18 13:03:36 [kernel] testing NMI watchdog ... OK. May 18 13:03:36 [kernel] DMI 2.3 present. May 18 13:03:36 [kernel] NET: Registered protocol family 16 May 18 13:03:36 [kernel] ACPI: bus type pci registered May 18 13:03:36 [kernel] PCI: Using configuration type 1 May 18 13:03:36 [kernel] PCI: Using MMCONFIG at e0000000 May 18 13:03:36 [kernel] ACPI: Subsystem revision 20060127 May 18 13:03:36 [kernel] evgpeblk-1037 [05] ev_initialize_gpe_bloc: Found 6 Wake, Enabled 1 Runtime GPEs in this block May 18 13:03:36 [kernel] Completing Region/Field/Buffer/Package initialization:................................................................................................... May 18 13:03:36 [kernel] Initialized 10/12 Regions 19/19 Fields 36/36 Buffers 34/35 Packages (565 nodes) May 18 13:03:36 [kernel] Executing all Device _STA and_INI methods:......................................................... May 18 13:03:36 [kernel] 57 Devices found - executed 0 _STA, 0 _INI methods May 18 13:03:36 [kernel] ACPI: Interpreter enabled May 18 13:03:36 [kernel] ACPI: Using PIC for interrupt routing May 18 13:03:36 [kernel] ACPI: PCI Root Bridge [PCI0] (0000:00) May 18 13:03:36 [kernel] PCI: Probing PCI hardware (bus 00) May 18 13:03:36 [kernel] PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1 May 18 13:03:36 [kernel] Boot video device is 0000:01:05.0 May 18 13:03:36 [kernel] PCI: Transparent bridge - 0000:00:14.4 May 18 13:03:36 [kernel] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] May 18 13:03:36 [kernel] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] May 18 13:03:36 [kernel] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT] May 18 13:03:36 [kernel] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 *15) May 18 13:03:36 [kernel] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 12 14 15) May 18 13:03:36 [kernel] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. May 18 13:03:36 [kernel] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 12 14 15) May 18 13:03:36 [kernel] ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 7 10 11 12 14 15) May 18 13:03:36 [kernel] ACPI: PCI Interrupt Link [LNKF] (IRQs *9) May 18 13:03:36 [kernel] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. May 18 13:03:36 [kernel] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 *11 12 14 15) May 18 13:03:36 [kernel] Linux Plug and Play Support v0.97 (c) Adam Belay May 18 13:03:36 [kernel] SCSI subsystem initialized May 18 13:03:36 [kernel] usbcore: registered new driver usbfs May 18 13:03:36 [kernel] usbcore: registered new driver hub May 18 13:03:36 [kernel] PCI: Using ACPI for IRQ routing May 18 13:03:36 [kernel] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report May 18 13:03:36 [kernel] PCI-DMA: Disabling IOMMU. May 18 13:03:36 [kernel] PCI: Bridge: 0000:00:01.0 May 18 13:03:36 [kernel] IO window: d000-dfff May 18 13:03:36 [kernel] MEM window: fea00000-feafffff May 18 13:03:36 [kernel] PREFETCH window: f0000000-f7ffffff May 18 13:03:36 [kernel] PCI: Bridge: 0000:00:14.4 May 18 13:03:36 [kernel] IO window: e000-efff May 18 13:03:36 [kernel] MEM window: feb00000-febfffff May 18 13:03:36 [kernel] PREFETCH window: 40000000-400fffff May 18 13:03:36 [kernel] IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ May 18 13:03:36 [kernel] Total HugeTLB memory allocated, 0 May 18 13:03:36 [kernel] io scheduler noop registered May 18 13:03:36 [kernel] io scheduler deadline registered (default) May 18 13:03:36 [kernel] io scheduler cfq registered May 18 13:03:36 [kernel] vesafb: framebuffer at 0xf0000000, mapped to 0xffffc20010100000, using 7680k, total 65536k May 18 13:03:36 [kernel] vesafb: mode is 1280x1024x24, linelength=3840, pages=16 May 18 13:03:36 [kernel] vesafb: scrolling: redraw May 18 13:03:36 [kernel] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 May 18 13:03:36 [kernel] Console: switching to colour frame buffer device 160x64 May 18 13:03:36 [kernel] fb0: VESA VGA frame buffer device May 18 13:03:36 [kernel] Real Time Clock Driver v1.12ac May 18 13:03:36 [kernel] Linux agpgart interface v0.101 (c) Dave Jones May 18 13:03:36 [kernel] PNP: No PS/2 controller found. Probing ports directly. May 18 13:03:36 [kernel] serio: i8042 AUX port at 0x60,0x64 irq 12 May 18 13:03:36 [kernel] serio: i8042 KBD port at 0x60,0x64 irq 1 May 18 13:03:36 [kernel] isa bounce pool size: 16 pages May 18 13:03:36 [kernel] RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize May 18 13:03:36 [kernel] loop: loaded (max 8 devices) May 18 13:03:36 [kernel] 8139too Fast Ethernet driver 0.9.27 May 18 13:03:36 [kernel] ACPI: PCI Interrupt Link [LNKE] BIOS reported IRQ 15, using IRQ 3 May 18 13:03:36 [kernel] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 3 May 18 13:03:36 [kernel] PCI: setting IRQ 3 as level-triggered May 18 13:03:36 [kernel] ACPI: PCI Interrupt 0000:02:03.0[A] -> Link [LNKE] -> GSI 3 (level, low) -> IRQ 3 May 18 13:03:36 [kernel] eth0: RealTek RTL8139 at 0xffffc20000004c00, 00:13:d3:ab:7a:d0, IRQ 3 May 18 13:03:36 [kernel] eth0: Identified 8139 chip type 'RTL-8100B/8139D' May 18 13:03:36 [kernel] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 May 18 13:03:36 [kernel] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx May 18 13:03:36 [kernel] ATIIXP: IDE controller at PCI slot 0000:00:14.1 May 18 13:03:36 [kernel] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 15 May 18 13:03:36 [kernel] PCI: setting IRQ 15 as level-triggered May 18 13:03:36 [kernel] ACPI: PCI Interrupt 0000:00:14.1[A] -> Link [LNKA] -> GSI 15 (level, low) -> IRQ 15 May 18 13:03:36 [kernel] ATIIXP: chipset revision 128 May 18 13:03:36 [kernel] ATIIXP: not 100% native mode: will probe irqs later May 18 13:03:36 [kernel] ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio May 18 13:03:36 [kernel] ATIIXP: simplex device: DMA disabled May 18 13:03:36 [kernel] ide1: ATIIXP Bus-Master DMA disabled (BIOS) May 18 13:03:36 [kernel] Probing IDE interface ide0... May 18 13:03:36 [kernel] hda: TSSTcorpCD/DVDW SH-W162C, ATAPI CD/DVD-ROM drive May 18 13:03:36 [kernel] Probing IDE interface ide1... - Last output repeated twice - May 18 13:03:36 [kernel] hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) May 18 13:03:36 [kernel] Uniform CD-ROM driver Revision: 3.20 May 18 13:03:36 [kernel] libata version 1.20 loaded. May 18 13:03:36 [kernel] sata_sil 0000:00:11.0: version 0.9 May 18 13:03:36 [kernel] acpi_bus-0201 [01] bus_set_power : Device is not power manageable May 18 13:03:36 [kernel] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11 May 18 13:03:36 [kernel] PCI: setting IRQ 11 as level-triggered May 18 13:03:36 [kernel] ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11 May 18 13:03:36 [kernel] ata1: SATA max UDMA/100 cmd 0xFFFFC20000006C80 ctl 0xFFFFC20000006C8A bmdma 0xFFFFC20000006C00 irq 11 May 18 13:03:36 [kernel] ata2: SATA max UDMA/100 cmd 0xFFFFC20000006CC0 ctl 0xFFFFC20000006CCA bmdma 0xFFFFC20000006C08 irq 11 May 18 13:03:36 [kernel] ata1: SATA link up 1.5 Gbps (SStatus 113) May 18 13:03:36 [kernel] ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e01 87:4663 88:407f May 18 13:03:36 [kernel] ata1: dev 0 ATA-7, max UDMA/133, 490234752 sectors: LBA48 May 18 13:03:36 [kernel] ata1: dev 0 configured for UDMA/100 May 18 13:03:36 [kernel] scsi0 : sata_sil May 18 13:03:36 [kernel] ata2: SATA link down (SStatus 0) May 18 13:03:36 [kernel] scsi1 : sata_sil May 18 13:03:36 [kernel] Vendor: ATA Model: Maxtor 6L250S0 Rev: BANC May 18 13:03:36 [kernel] Type: Direct-Access ANSI SCSI revision: 05 May 18 13:03:36 [kernel] SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB) May 18 13:03:36 [kernel] sda: Write Protect is off May 18 13:03:36 [kernel] sda: Mode Sense: 00 3a 00 00 May 18 13:03:36 [kernel] SCSI device sda: drive cache: write back May 18 13:03:36 [kernel] SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB) May 18 13:03:36 [kernel] sda: Write Protect is off May 18 13:03:36 [kernel] sda: Mode Sense: 00 3a 00 00 May 18 13:03:36 [kernel] SCSI device sda: drive cache: write back May 18 13:03:36 [kernel] sda: sda1 sda2 sda3 sda4 < sda5 > May 18 13:03:36 [kernel] sd 0:0:0:0: Attached scsi disk sda May 18 13:03:36 [kernel] ieee1394: raw1394: /dev/raw1394 device initialized May 18 13:03:36 [kernel] usbmon: debugfs is not available May 18 13:03:36 [kernel] acpi_bus-0201 [01] bus_set_power : Device is not power manageable May 18 13:03:36 [kernel] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5 May 18 13:03:36 [kernel] Losing some ticks... checking if CPU frequency changed. May 18 13:03:36 [kernel] PCI: setting IRQ 5 as level-triggered May 18 13:03:36 [kernel] ACPI: PCI Interrupt 0000:00:13.2[A] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5 May 18 13:03:36 [kernel] ehci_hcd 0000:00:13.2: EHCI Host Controller May 18 13:03:36 [kernel] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1 May 18 13:03:36 [kernel] ehci_hcd 0000:00:13.2: irq 5, io mem 0xfe9f8000 May 18 13:03:36 [kernel] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 May 18 13:03:36 [kernel] usb usb1: configuration #1 chosen from 1 choice May 18 13:03:36 [kernel] hub 1-0:1.0: USB hub found May 18 13:03:36 [kernel] hub 1-0:1.0: 8 ports detected May 18 13:03:36 [kernel] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) May 18 13:03:36 [kernel] ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5 May 18 13:03:36 [kernel] ohci_hcd 0000:00:13.0: OHCI Host Controller May 18 13:03:36 [kernel] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2 May 18 13:03:36 [kernel] ohci_hcd 0000:00:13.0: irq 5, io mem 0xfe9fa000 May 18 13:03:36 [kernel] usb usb2: configuration #1 chosen from 1 choice May 18 13:03:36 [kernel] hub 2-0:1.0: USB hub found May 18 13:03:36 [kernel] usb 1-4: new high speed USB device using ehci_hcd and address 2 May 18 13:03:36 [kernel] hub 2-0:1.0: 4 ports detected May 18 13:03:36 [kernel] ACPI: PCI Interrupt 0000:00:13.1[A] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5 May 18 13:03:36 [kernel] ohci_hcd 0000:00:13.1: OHCI Host Controller May 18 13:03:36 [kernel] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 May 18 13:03:36 [kernel] ohci_hcd 0000:00:13.1: irq 5, io mem 0xfe9f9000 May 18 13:03:36 [kernel] usb 1-4: configuration #1 chosen from 1 choice May 18 13:03:36 [kernel] hub 1-4:1.0: USB hub found May 18 13:03:36 [kernel] hub 1-4:1.0: 4 ports detected May 18 13:03:36 [kernel] usb usb3: configuration #1 chosen from 1 choice May 18 13:03:36 [kernel] hub 3-0:1.0: USB hub found May 18 13:03:36 [kernel] hub 3-0:1.0: 4 ports detected May 18 13:03:36 [kernel] Initializing USB Mass Storage driver... May 18 13:03:36 [kernel] usbcore: registered new driver usb-storage May 18 13:03:36 [kernel] USB Mass Storage support registered. May 18 13:03:36 [kernel] usbcore: registered new driver hiddev May 18 13:03:36 [kernel] usbcore: registered new driver usbhid May 18 13:03:36 [kernel] drivers/usb/input/hid-core.c: v2.6:USB HID core driver May 18 13:03:36 [kernel] mice: PS/2 mouse device common for all mice May 18 13:03:36 [kernel] input: AT Translated Set 2 keyboard as /class/input/input0 May 18 13:03:36 [kernel] logips2pp: Detected unknown logitech mouse model 1 May 18 13:03:36 [kernel] input: PS/2 Logitech Mouse as /class/input/input1 May 18 13:03:36 [kernel] input: PC Speaker as /class/input/input2 May 18 13:03:36 [kernel] NET: Registered protocol family 2 May 18 13:03:36 [kernel] IP route cache hash table entries: 32768 (order: 6, 262144 bytes) May 18 13:03:36 [kernel] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) May 18 13:03:36 [kernel] TCP reno registered May 18 13:03:36 [kernel] TCP bic registered May 18 13:03:36 [kernel] NET: Registered protocol family 1 May 18 13:03:36 [kernel] NET: Registered protocol family 17 May 18 13:03:36 [kernel] EXT3-fs: mounted filesystem with ordered data mode. May 18 13:03:36 [kernel] VFS: Mounted root (ext3 filesystem) readonly. May 18 13:03:36 [kernel] Freeing unused kernel memory: 184k freed May 18 13:03:36 [kernel] kjournald starting. Commit interval 5 seconds May 18 13:03:36 [kernel] acpi_bus-0201 [01] bus_set_power : Device is not power manageable May 18 13:03:36 [kernel] ACPI: PCI Interrupt 0000:00:14.2[A] -> Link [LNKA] -> GSI 15 (level, low) -> IRQ 15 May 18 13:03:36 [kernel] hda_codec: Unknown model for ALC880, trying auto-probe from BIOS... May 18 13:03:36 [kernel] Adding 1959920k swap on /dev/sda2. Priority:-1 extents:1 across:1959920k May 18 13:03:36 [kernel] EXT3 FS on sda3, internal journal May 18 13:03:36 [kernel] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 May 18 13:03:36 [kernel] irq 15: nobody cared (try booting with the "irqpoll" option) May 18 13:03:36 [kernel] Call Trace: <IRQ> <ffffffff8014c735>{__report_bad_irq+53} May 18 13:03:36 [kernel] <ffffffff8014ca0e>{note_interrupt+638} <ffffffff8014c0fe>{__do_IRQ+238} May 18 13:03:36 [kernel] <ffffffff8010d782>{do_IRQ+66} <ffffffff80109ad0>{default_idle+0} May 18 13:03:36 [kernel] <ffffffff8010b240>{ret_from_intr+0} <EOI> <ffffffff8035b713>{thread_return+68} May 18 13:03:36 [kernel] <ffffffff80109afa>{default_idle+42} <ffffffff80109b6d>{cpu_idle+61} May 18 13:03:36 [kernel] <ffffffff8048486f>{start_kernel+495} <ffffffff80484267>{_sinittext+615} May 18 13:03:36 [kernel] handlers: May 18 13:03:36 [kernel] [<ffffffff8805b410>] (azx_interrupt+0x0/0x1d0 [snd_hda_intel]) May 18 13:03:36 [kernel] NETDEV WATCHDOG: eth0: transmit timed out May 18 13:03:36 [kernel] eth0: Transmit timeout, status 0c 0005 c07f media 10. May 18 13:03:36 [kernel] eth0: Tx queue start entry 4 dirty entry 0. May 18 13:03:36 [kernel] eth0: Tx descriptor 0 is 0008a24e. (queue head) May 18 13:03:36 [kernel] eth0: Tx descriptor 1 is 0008a24e. May 18 13:03:36 [kernel] eth0: Tx descriptor 2 is 0008a24e. May 18 13:03:36 [kernel] eth0: Tx descriptor 3 is 0008a24e. May 18 13:03:36 [kernel] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 May 18 13:03:36 [kernel] NETDEV WATCHDOG: eth0: transmit timed out May 18 13:03:36 [kernel] eth0: Transmit timeout, status 0c 0005 c07f media 10. May 18 13:03:36 [kernel] eth0: Tx queue start entry 4 dirty entry 0. May 18 13:03:36 [kernel] eth0: Tx descriptor 0 is 0008a24e. (queue head) May 18 13:03:36 [kernel] eth0: Tx descriptor 1 is 0008a24e. May 18 13:03:36 [kernel] eth0: Tx descriptor 2 is 0008a24e. May 18 13:03:36 [kernel] eth0: Tx descriptor 3 is 0008a24e. May 18 13:03:36 [kernel] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 May 18 13:03:38 [kernel] [drm] Initialized drm 1.0.1 20051102 May 18 13:03:40 [kernel] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 May 18 13:03:40 [kernel] spurious 8259A interrupt: IRQ7. May 18 13:04:16 [kernel] NETDEV WATCHDOG: eth0: transmit timed out May 18 13:04:19 [kernel] eth0: Transmit timeout, status 0c 0005 c07f media 10. May 18 13:04:19 [kernel] eth0: Tx queue start entry 4 dirty entry 0. May 18 13:04:19 [kernel] eth0: Tx descriptor 0 is 0008a24e. (queue head) May 18 13:04:19 [kernel] eth0: Tx descriptor 1 is 0008a24e. May 18 13:04:19 [kernel] eth0: Tx descriptor 2 is 0008a24e. May 18 13:04:19 [kernel] eth0: Tx descriptor 3 is 0008a24e. May 18 13:04:19 [kernel] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 May 18 13:04:35 [kernel] azx_get_response timeout I also tried applying http://ftp.kernel.org/pub/linux/kernel/people/lenb/acpi/patches/test/2.6.16/acpi-acpica-20060310-2.6.16.diff.gz to a 2.6.16 kernel, but this doesn't seem to be the way.
I tried my own patch again, to see if I could get the log and see if it is really the same as the other patch. For some reason though, this time it booted cleanly. Here is dmesg: Bootdata ok (command line is root=/dev/sda3 vga=0x31B video=vesafb:ywrap,mtrr noapic) Linux version 2.6.16.14 (marijn@hakbak) (gcc version 4.1.0 (Gentoo 4.1.0)) #5 PREEMPT Thu May 18 13:40:42 CEST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003bfd0000 (usable) BIOS-e820: 000000003bfd0000 - 000000003bfde000 (ACPI data) BIOS-e820: 000000003bfde000 - 000000003c000000 (ACPI NVS) BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) ACPI: Scanning for RSDP signature... <6>ACPI: done ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000f96e0 ACPI: RSDT (v001 A M I OEMRSDT 0x10000514 MSFT 0x00000097) @ 0x000000003bfd0000 ACPI: FADT (v002 A M I OEMFACP 0x10000514 MSFT 0x00000097) @ 0x000000003bfd0200 ACPI: MADT (v001 A M I OEMAPIC 0x10000514 MSFT 0x00000097) @ 0x000000003bfd0390 ACPI: MCFG (v001 A M I OEMMCFG 0x10000514 MSFT 0x00000097) @ 0x000000003bfd03f0 ACPI: OEMB (v001 A M I AMI_OEM 0x10000514 MSFT 0x00000097) @ 0x000000003bfde040 ACPI: DSDT (v001 1ABZR 1ABZRB49 0x00000b49 INTL 0x02002026) @ 0x0000000000000000 On node 0 totalpages: 241303 DMA zone: 2990 pages, LIFO batch:0 DMA32 zone: 238313 pages, LIFO batch:31 Normal zone: 0 pages, LIFO batch:0 HighMem zone: 0 pages, LIFO batch:0 ATI board detected. Disabling timer routing over 8254. ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:15 APIC version 16 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) ACPI: Skipping IOAPIC probe due to 'noapic' option. Using ACPI for processor (LAPIC) configuration information Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: ATI Product ID: RS480 APIC at: 0xFEE00000 I/O APIC #1 Version 33 at 0xFEC00000. Setting APIC routing to flat Processors: 1 Allocating PCI resources starting at 40000000 (gap: 3c000000:c3780000) Checking aperture... CPU 0: aperture @ 77ee000000 size 32 MB Aperture from northbridge cpu 0 too small (32 MB) No AGP bridge found Built 1 zonelists Kernel command line: root=/dev/sda3 vga=0x31B video=vesafb:ywrap,mtrr noapic Initializing CPU#0 PID hash table entries: 4096 (order: 12, 131072 bytes) time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer. time.c: Detected 1994.229 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Memory: 963232k/982848k available (2431k kernel code, 18940k reserved, 902k data, 184k init) Calibrating delay using timer specific routine.. 3994.00 BogoMIPS (lpj=1997002) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 02 tbxface-0109 [02] load_tables : ACPI Tables successfully acquired Parsing all Control Methods: Table [DSDT](id 0005) - 556 Objects with 53 Devices 164 Methods 12 Regions ACPI Namespace successfully loaded at root ffffffff80467aa0 ACPI: setting ELCR to 0200 (from 8e20) evxfevnt-0091 [03] enable : Transition to ACPI mode successful Using local APIC timer interrupts. result 12463939 Detected 12.463 MHz APIC timer. testing NMI watchdog ... OK. DMI 2.3 present. NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using configuration type 1 PCI: Using MMCONFIG at e0000000 ACPI: Subsystem revision 20060127 evgpeblk-0941 [06] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9 evgpeblk-1037 [05] ev_initialize_gpe_bloc: Found 6 Wake, Enabled 1 Runtime GPEs in this block Completing Region/Field/Buffer/Package initialization:................................................................................................... Initialized 10/12 Regions 19/19 Fields 36/36 Buffers 34/35 Packages (565 nodes) Executing all Device _STA and_INI methods:......................................................... 57 Devices found - executed 0 _STA, 0 _INI methods ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1 Boot video device is 0000:01:05.0 PCI: Transparent bridge - 0000:00:14.4 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 *15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 *15) ACPI: PCI Interrupt Link [LNKF] (IRQs *9) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 *11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI-DMA: Disabling IOMMU. PCI: Bridge: 0000:00:01.0 IO window: d000-dfff MEM window: fea00000-feafffff PREFETCH window: f0000000-f7ffffff PCI: Bridge: 0000:00:14.4 IO window: e000-efff MEM window: feb00000-febfffff PREFETCH window: 40000000-400fffff IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ Total HugeTLB memory allocated, 0 io scheduler noop registered io scheduler deadline registered (default) io scheduler cfq registered vesafb: framebuffer at 0xf0000000, mapped to 0xffffc20010100000, using 7680k, total 65536k vesafb: mode is 1280x1024x24, linelength=3840, pages=16 vesafb: scrolling: redraw vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 Console: switching to colour frame buffer device 160x64 fb0: VESA VGA frame buffer device Real Time Clock Driver v1.12ac Linux agpgart interface v0.101 (c) Dave Jones PNP: No PS/2 controller found. Probing ports directly. serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 isa bounce pool size: 16 pages RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) 8139too Fast Ethernet driver 0.9.27 ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 15 PCI: setting IRQ 15 as level-triggered ACPI: PCI Interrupt 0000:02:03.0[A] -> Link [LNKE] -> GSI 15 (level, low) -> IRQ 15 eth0: RealTek RTL8139 at 0xffffc20000004c00, 00:13:d3:ab:7a:d0, IRQ 15 eth0: Identified 8139 chip type 'RTL-8100B/8139D' Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ATIIXP: IDE controller at PCI slot 0000:00:14.1 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 15 ACPI: PCI Interrupt 0000:00:14.1[A] -> Link [LNKA] -> GSI 15 (level, low) -> IRQ 15 ATIIXP: chipset revision 128 ATIIXP: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio ATIIXP: simplex device: DMA disabled ide1: ATIIXP Bus-Master DMA disabled (BIOS) Probing IDE interface ide0... hda: TSSTcorpCD/DVDW SH-W162C, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... Probing IDE interface ide1... hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 libata version 1.20 loaded. sata_sil 0000:00:11.0: version 0.9 acpi_bus-0201 [01] bus_set_power : Device is not power manageable ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11 ata1: SATA max UDMA/100 cmd 0xFFFFC20000006C80 ctl 0xFFFFC20000006C8A bmdma 0xFFFFC20000006C00 irq 11 ata2: SATA max UDMA/100 cmd 0xFFFFC20000006CC0 ctl 0xFFFFC20000006CCA bmdma 0xFFFFC20000006C08 irq 11 ata1: SATA link up 1.5 Gbps (SStatus 113) ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e01 87:4663 88:407f ata1: dev 0 ATA-7, max UDMA/133, 490234752 sectors: LBA48 ata1: dev 0 configured for UDMA/100 scsi0 : sata_sil ata2: SATA link down (SStatus 0) scsi1 : sata_sil Vendor: ATA Model: Maxtor 6L250S0 Rev: BANC Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sda4 < sda5 > sd 0:0:0:0: Attached scsi disk sda ieee1394: raw1394: /dev/raw1394 device initialized usbmon: debugfs is not available acpi_bus-0201 [01] bus_set_power : Device is not power manageable ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:13.2[A] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5 Losing some ticks... checking if CPU frequency changed. ehci_hcd 0000:00:13.2: EHCI Host Controller ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:13.2: irq 5, io mem 0xfe9f8000 ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5 ohci_hcd 0000:00:13.0: OHCI Host Controller ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:13.0: irq 5, io mem 0xfe9fa000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found usb 1-4: new high speed USB device using ehci_hcd and address 2 hub 2-0:1.0: 4 ports detected ACPI: PCI Interrupt 0000:00:13.1[A] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5 ohci_hcd 0000:00:13.1: OHCI Host Controller ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:13.1: irq 5, io mem 0xfe9f9000 usb 1-4: configuration #1 chosen from 1 choice hub 1-4:1.0: USB hub found hub 1-4:1.0: 4 ports detected usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 4 ports detected Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input0 logips2pp: Detected unknown logitech mouse model 1 input: PS/2 Logitech Mouse as /class/input/input1 input: PC Speaker as /class/input/input2 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 6, 262144 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 184k freed kjournald starting. Commit interval 5 seconds acpi_bus-0201 [01] bus_set_power : Device is not power manageable ACPI: PCI Interrupt 0000:00:14.2[A] -> Link [LNKA] -> GSI 15 (level, low) -> IRQ 15 hda_codec: Unknown model for ALC880, trying auto-probe from BIOS... Adding 1959920k swap on /dev/sda2. Priority:-1 extents:1 across:1959920k EXT3 FS on sda3, internal journal eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 [drm] Initialized drm 1.0.1 20051102 spurious 8259A interrupt: IRQ7. ACPI seems to be working, at least I now have /proc/acpi/dsdt
I still don't know why it works now, but didn't work before, but I was able to boot without noapic and also didn't get a double speed timer :) although there is one new error. Resolving this bug for now, since my patch seems to be working. Here is the dmesg without noapic: Bootdata ok (command line is root=/dev/sda3 vga=0x31B video=vesafb:ywrap,mtrr) Linux version 2.6.16.14 (marijn@hakbak) (gcc version 4.1.0 (Gentoo 4.1.0)) #5 PREEMPT Thu May 18 13:40:42 CEST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003bfd0000 (usable) BIOS-e820: 000000003bfd0000 - 000000003bfde000 (ACPI data) BIOS-e820: 000000003bfde000 - 000000003c000000 (ACPI NVS) BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) ACPI: Scanning for RSDP signature... <6>ACPI: done ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000f96e0 ACPI: RSDT (v001 A M I OEMRSDT 0x10000514 MSFT 0x00000097) @ 0x000000003bfd0000 ACPI: FADT (v002 A M I OEMFACP 0x10000514 MSFT 0x00000097) @ 0x000000003bfd0200 ACPI: MADT (v001 A M I OEMAPIC 0x10000514 MSFT 0x00000097) @ 0x000000003bfd0390 ACPI: MCFG (v001 A M I OEMMCFG 0x10000514 MSFT 0x00000097) @ 0x000000003bfd03f0 ACPI: OEMB (v001 A M I AMI_OEM 0x10000514 MSFT 0x00000097) @ 0x000000003bfde040 ACPI: DSDT (v001 1ABZR 1ABZRB49 0x00000b49 INTL 0x02002026) @ 0x0000000000000000 On node 0 totalpages: 241303 DMA zone: 2990 pages, LIFO batch:0 DMA32 zone: 238313 pages, LIFO batch:31 Normal zone: 0 pages, LIFO batch:0 HighMem zone: 0 pages, LIFO batch:0 ATI board detected. Disabling timer routing over 8254. ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:15 APIC version 16 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. Setting APIC routing to flat Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 40000000 (gap: 3c000000:c3780000) Checking aperture... CPU 0: aperture @ 77ee000000 size 32 MB Aperture from northbridge cpu 0 too small (32 MB) No AGP bridge found Built 1 zonelists Kernel command line: root=/dev/sda3 vga=0x31B video=vesafb:ywrap,mtrr Initializing CPU#0 PID hash table entries: 4096 (order: 12, 131072 bytes) time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer. time.c: Detected 1994.259 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Memory: 963232k/982848k available (2431k kernel code, 18940k reserved, 902k data, 184k init) Calibrating delay using timer specific routine.. 3993.92 BogoMIPS (lpj=1996964) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 02 tbxface-0109 [02] load_tables : ACPI Tables successfully acquired Parsing all Control Methods: Table [DSDT](id 0005) - 556 Objects with 53 Devices 164 Methods 12 Regions ACPI Namespace successfully loaded at root ffffffff80467aa0 evxfevnt-0091 [03] enable : Transition to ACPI mode successful ..MP-BIOS bug: 8254 timer not connected to IO-APIC failed. works. Using local APIC timer interrupts. result 12464137 Detected 12.464 MHz APIC timer. testing NMI watchdog ... OK. DMI 2.3 present. NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using configuration type 1 PCI: Using MMCONFIG at e0000000 ACPI: Subsystem revision 20060127 evgpeblk-0941 [06] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9 GSI 21 sharing vector 0xA9 and IRQ 21 evgpeblk-1037 [05] ev_initialize_gpe_bloc: Found 6 Wake, Enabled 1 Runtime GPEs in this block Completing Region/Field/Buffer/Package initialization:................................................................................................... Initialized 10/12 Regions 19/19 Fields 36/36 Buffers 34/35 Packages (565 nodes) Executing all Device _STA and_INI methods:......................................................... 57 Devices found - executed 0 _STA, 0 _INI methods ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1 Boot video device is 0000:01:05.0 PCI: Transparent bridge - 0000:00:14.4 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI-DMA: Disabling IOMMU. PCI: Bridge: 0000:00:01.0 IO window: d000-dfff MEM window: fea00000-feafffff PREFETCH window: f0000000-f7ffffff PCI: Bridge: 0000:00:14.4 IO window: e000-efff MEM window: feb00000-febfffff PREFETCH window: 40000000-400fffff IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ Total HugeTLB memory allocated, 0 io scheduler noop registered io scheduler deadline registered (default) io scheduler cfq registered vesafb: framebuffer at 0xf0000000, mapped to 0xffffc20010100000, using 7680k, total 65536k vesafb: mode is 1280x1024x24, linelength=3840, pages=16 vesafb: scrolling: redraw vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 Console: switching to colour frame buffer device 160x64 fb0: VESA VGA frame buffer device Real Time Clock Driver v1.12ac Linux agpgart interface v0.101 (c) Dave Jones PNP: No PS/2 controller found. Probing ports directly. serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 isa bounce pool size: 16 pages RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) 8139too Fast Ethernet driver 0.9.27 GSI 16 sharing vector 0xB1 and IRQ 16 ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 16 eth0: RealTek RTL8139 at 0xffffc20000004c00, 00:13:d3:ab:7a:d0, IRQ 16 eth0: Identified 8139 chip type 'RTL-8100B/8139D' Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ATIIXP: IDE controller at PCI slot 0000:00:14.1 GSI 17 sharing vector 0xB9 and IRQ 17 ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17 ATIIXP: chipset revision 128 ATIIXP: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio ATIIXP: simplex device: DMA disabled ide1: ATIIXP Bus-Master DMA disabled (BIOS) Probing IDE interface ide0... hda: TSSTcorpCD/DVDW SH-W162C, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... Probing IDE interface ide1... hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 libata version 1.20 loaded. sata_sil 0000:00:11.0: version 0.9 acpi_bus-0201 [01] bus_set_power : Device is not power manageable GSI 18 sharing vector 0xC1 and IRQ 18 ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 23 (level, low) -> IRQ 18 ata1: SATA max UDMA/100 cmd 0xFFFFC20000006C80 ctl 0xFFFFC20000006C8A bmdma 0xFFFFC20000006C00 irq 18 ata2: SATA max UDMA/100 cmd 0xFFFFC20000006CC0 ctl 0xFFFFC20000006CCA bmdma 0xFFFFC20000006C08 irq 18 ata1: SATA link up 1.5 Gbps (SStatus 113) ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e01 87:4663 88:407f ata1: dev 0 ATA-7, max UDMA/133, 490234752 sectors: LBA48 ata1: dev 0 configured for UDMA/100 scsi0 : sata_sil ata2: SATA link down (SStatus 0) scsi1 : sata_sil Vendor: ATA Model: Maxtor 6L250S0 Rev: BANC Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sda4 < sda5 > sd 0:0:0:0: Attached scsi disk sda ieee1394: raw1394: /dev/raw1394 device initialized usbmon: debugfs is not available acpi_bus-0201 [01] bus_set_power : Device is not power manageable GSI 19 sharing vector 0xC9 and IRQ 19 ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19 Losing some ticks... checking if CPU frequency changed. ehci_hcd 0000:00:13.2: EHCI Host Controller ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:13.2: irq 19, io mem 0xfe9f8000 ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19 ohci_hcd 0000:00:13.0: OHCI Host Controller ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:13.0: irq 19, io mem 0xfe9fa000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found usb 1-4: new high speed USB device using ehci_hcd and address 2 hub 2-0:1.0: 4 ports detected ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19 ohci_hcd 0000:00:13.1: OHCI Host Controller ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:13.1: irq 19, io mem 0xfe9f9000 usb 1-4: configuration #1 chosen from 1 choice hub 1-4:1.0: USB hub found hub 1-4:1.0: 4 ports detected usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 4 ports detected Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input0 logips2pp: Detected unknown logitech mouse model 1 input: PS/2 Logitech Mouse as /class/input/input1 input: PC Speaker as /class/input/input2 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 6, 262144 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 184k freed kjournald starting. Commit interval 5 seconds APIC error on CPU0: 04(40) acpi_bus-0201 [01] bus_set_power : Device is not power manageable ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 17 hda_codec: Unknown model for ALC880, trying auto-probe from BIOS... Adding 1959920k swap on /dev/sda2. Priority:-1 extents:1 across:1959920k EXT3 FS on sda3, internal journal eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 [drm] Initialized drm 1.0.1 20051102 APIC error on CPU0: 40(40) APIC error on CPU0: 40(40)
fixed in ACPICA 20060331, which shipped in Linux-2.6.17-git9.
I don't know which patch was included, but in kernel 2.6.17.6 I get varied problems culminating in a kernel panic. All problems go away again when I use the simple patch in comment #1.
Using a 2.6.19.1 based gentoo kernel it seems to finally be working: ACPI: Core revision 20060707 tbxface-0107 [01] load_tables : ACPI Tables successfully acquired nssearch-0335 [11] ns_search_and_enter : Found bad character(s) in name, repaired: [PS*C] nssearch-0335 [11] ns_search_and_enter : Found bad character(s) in name, repaired: [PS*C] Parsing all Control Methods: Table [DSDT](id 0005) - 556 Objects with 53 Devices 164 Methods 12 Regions ACPI Namespace successfully loaded at root ffffffff8057a720 evxfevnt-0089 [02] enable : Transition to ACPI mode successful ..MP-BIOS bug: 8254 timer not connected to IO-APIC Using local APIC timer interrupts. result 12464323 Detected 12.464 MHz APIC timer. testing NMI watchdog ... OK. Thank you.
> fixed in ACPICA 20060331, which shipped in Linux-2.6.17-git9 which shipped in Linux-2.6.18 closed.