Most recent kernel where this bug did not occur: 2.6.13.5 Distribution: Slackware Hardware Environment: 2x Dual Core Opteron AMDs on a Tyan K8WE (S2895) board which has an LSI 53C1030 U320 SCSI controller Software Environment: Problem Description: The kernel panics when I try to boot the system with a 2.6.15.4 (and 2.6.14.7) kernel compiled from source, while 2.6.13.5 works fine. The config for the kernel is the same in all instances. I do not have a dump, but what appears to happen is that the scsi controller does not get detected and hence the root filesystem of my scsi drive is not mounted, so the kernel panics with the typical: VFS: Cannot open root device "812" or unknown-block(8,18) Please append a correct "root=" boot option Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,18) After the Fusion MPT driver is loaded there are no relevant devices detected, as in 2.6.13.5.
The fusion config entries got renamed around 2.6.14, I think. What does `grep FUSION .config' say? Mine gives: CONFIG_FUSION=y CONFIG_FUSION_SPI=y CONFIG_FUSION_FC=y CONFIG_FUSION_SAS=y CONFIG_FUSION_MAX_SGE=128 CONFIG_FUSION_CTL=y
bugme-daemon@bugzilla.kernel.org wrote: > http://bugzilla.kernel.org/show_bug.cgi?id=6060 > > akpm@osdl.org changed: > > What |Removed |Added > ---------------------------------------------------------------------------- > CC| |akpm@osdl.org > > > > ------- Additional Comments From akpm@osdl.org 2006-02-12 14:02 ------- > The fusion config entries got renamed around 2.6.14, I think. > > What does `grep FUSION .config' say? Mine gives: > > > CONFIG_FUSION=y > CONFIG_FUSION_SPI=y > CONFIG_FUSION_FC=y > CONFIG_FUSION_SAS=y > CONFIG_FUSION_MAX_SGE=128 > CONFIG_FUSION_CTL=y > > > ------- You are receiving this mail because: ------- > You reported the bug, or are watching the reporter. on 2.6.13.5 (that works): CONFIG_FUSION=y CONFIG_FUSION_SPI=y CONFIG_FUSION_FC=y CONFIG_FUSION_MAX_SGE=128 CONFIG_FUSION_CTL=m and on 2.6.15.4 (the one that doesn't): CONFIG_FUSION=y CONFIG_FUSION_SPI=y CONFIG_FUSION_FC=y # CONFIG_FUSION_SAS is not set CONFIG_FUSION_MAX_SGE=128 CONFIG_FUSION_CTL=m let me know if I should attempt some other combination.
I suggest you set them all to `y', see what happens.
If it still fails, we'd need to see the full `dmesg -s 1000000' output, if you can find some way of gathering it?
Ok, I enabled everything in 2.6.15.4, that is: CONFIG_FUSION=y CONFIG_FUSION_SPI=y CONFIG_FUSION_FC=y CONFIG_FUSION_SAS=y CONFIG_FUSION_MAX_SGE=128 CONFIG_FUSION_CTL=y It still crashes, same bootup sequence as far as I can tell, just a few more drivers loaded. I cannot gather the dmesg from the kernel that fails, I am sorry the kernel panics and I'm left half way through bootup. I got it from the 2.6.13.5 which works and I attach it. I looked at the bootup sequence of 2.6.15.4 and the chunk that does the fusion MPT driver setup is similar, but like this: Fusion MPT base driver 3.03.04 Copyright (c) 1999-2005 LSI Logic Corporation Fusion MPT SPI Host driver 3.03.04 Fusion MPT FC Host driver 3.03.04 Fusion MPT SAS Host driver 3.03.04 Fusion MPT misc device (ioctl) driver 3.03.04 mptctl: Registered with Fusion MPT base driver mptctl: /dev/mptctl @ (major,minor=10,220) and then it carries on with ohci stuff which looks suspect: ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org> ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 19 ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNK4] -> GSI 19 (level, high) -> IRQ 18 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[b0104000-b01047ff] Max Packet=[2048] I think that IRQ 18 is supposed to be used by the LSI controller, according at least to the dmesg of the working kernel. Let me know if there is anything else I can provide. Linux version 2.6.13.5 (root@slackware) (gcc version 3.3.6) #1 SMP Sun Feb 12 22:51:46 CET 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009ac00 (usable) BIOS-e820: 000000000009ac00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000da000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007ff90000 (usable) BIOS-e820: 000000007ff90000 - 000000007ff97000 (ACPI data) BIOS-e820: 000000007ff97000 - 0000000080000000 (ACPI NVS) BIOS-e820: 0000000080000000 - 00000000aff80000 (usable) BIOS-e820: 00000000aff80000 - 00000000b0000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec00400 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) BIOS-e820: 0000000100000000 - 0000000150000000 (usable) Warning only 4GB will be used. Use a PAE enabled kernel. 3200MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000f7950 On node 0 totalpages: 1048576 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 225280 pages, LIFO batch:31 HighMem zone: 819200 pages, LIFO batch:31 DMI present. ACPI: RSDP (v000 PTLTD ) @ 0x000f7920 ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x7ff926a5 ACPI: FADT (v001 NVIDIA CK8S 0x06040000 PTL_ 0x000f4240) @ 0x7ff96c90 ACPI: SRAT (v001 AMD HAMMER 0x06040000 AMD 0x00000001) @ 0x7ff96d04 ACPI: SPCR (v001 PTLTD $UCRTBL$ 0x06040000 PTL 0x00000001) @ 0x7ff96e14 ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x7ff96e64 ACPI: MCFG (v001 PTLTD MCFG 0x06040000 LTP 0x00000000) @ 0x7ff96f00 ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x7ff96f3c ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x7ff96fd8 ACPI: DSDT (v001 NVIDIA CK8 0x06040000 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x8008 ACPI: Local APIC address 0xfee00000 ACPI: 2 duplicate APIC table ignored. ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:1 APIC version 16 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 15:1 APIC version 16 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) Processor #2 15:1 APIC version 16 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled) Processor #3 15:1 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x05] address[0xd0000000] gsi_base[24]) IOAPIC[1]: apic_id 5, version 17, address 0xd0000000, GSI 24-27 ACPI: IOAPIC (id[0x06] address[0xd0001000] gsi_base[28]) IOAPIC[2]: apic_id 6, version 17, address 0xd0001000, GSI 28-31 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) ACPI: BIOS IRQ0 pin2 override ignored. ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 3 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at b0000000 (gap: b0000000:30000000) Built 1 zonelists Kernel command line: BOOT_IMAGE=linux-2.6.13.5 ro root=812 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) mapped IOAPIC to ffffb000 (d0000000) mapped IOAPIC to ffffa000 (d0001000) Initializing CPU#0 PID hash table entries: 4096 (order: 12, 65536 bytes) Detected 2411.293 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x60 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 2843172k/4194304k available (3019k kernel code, 38216k reserved, 896k data, 212k init, 1965120k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 4827.46 BogoMIPS (lpj=9654932) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: After vendor identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 0(2) -> Core 0 CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000010 00000001 00000000 00000003 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. mtrr: v2.0 (20020519) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. CPU0: AMD Dual Core AMD Opteron(tm) Processor 280 stepping 02 Booting processor 1/1 eip 2000 Initializing CPU#1 Calibrating delay using timer specific routine.. 4822.58 BogoMIPS (lpj=9645163) CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: After vendor identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 1(2) -> Core 1 CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000010 00000001 00000000 00000003 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: AMD Dual Core AMD Opteron(tm) Processor 280 stepping 02 Booting processor 2/2 eip 2000 Initializing CPU#2 Calibrating delay using timer specific routine.. 4822.69 BogoMIPS (lpj=9645394) CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: After vendor identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 2(2) -> Core 1 CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000010 00000001 00000000 00000003 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#2. CPU2: AMD Dual Core AMD Opteron(tm) Processor 280 stepping 02 Booting processor 3/3 eip 2000 Initializing CPU#3 Calibrating delay using timer specific routine.. 4822.66 BogoMIPS (lpj=9645322) CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: After vendor identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 3(2) -> Core 1 CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000010 00000001 00000000 00000003 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#3. CPU3: AMD Dual Core AMD Opteron(tm) Processor 280 stepping 02 Total of 4 processors activated (19295.40 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 pin1=0 pin2=-1 checking TSC synchronization across 4 CPUs: passed. Brought up 4 CPUs NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd6b0, last bus=129 PCI: Using configuration type 1 ACPI: Subsystem revision 20050408 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] segment is 0 ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 ACPI: Assume root bridge [\_SB_.PCI2] segment is 0 ACPI: Assume root bridge [\_SB_.PCI1] segment is 0 PCI: Transparent bridge - 0000:00:09.0 Boot video device is 0000:02:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LNK3] (IRQs 16 17 18 19) *0 ACPI: PCI Interrupt Link [LNK4] (IRQs 16 17 18 19) *0 ACPI: PCI Interrupt Link [LNK5] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LSI1] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Root Bridge [PCI2] (0000:08) PCI: Probing PCI hardware (bus 08) ACPI: Assume root bridge [\_SB_.PCI0] segment is 0 ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 ACPI: Assume root bridge [\_SB_.PCI2] segment is 0 ACPI: Assume root bridge [\_SB_.PCI1] segment is 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI2.G0PA._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI2.G0PB._PRT] ACPI: PCI Root Bridge [PCI1] (0000:80) PCI: Probing PCI hardware (bus 80) ACPI: Assume root bridge [\_SB_.PCI0] segment is 0 ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 ACPI: Assume root bridge [\_SB_.PCI2] segment is 0 ACPI: Assume root bridge [\_SB_.PCI1] segment is 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.XVR0._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Bridge: 0000:00:09.0 IO window: disabled. MEM window: b0100000-b01fffff PREFETCH window: disabled. PCI: Failed to allocate mem resource #6:20000@d0000000 for 0000:02:00.0 PCI: Bridge: 0000:00:0e.0 IO window: disabled. MEM window: b1000000-b2ffffff PREFETCH window: c0000000-cfffffff PCI: Setting latency timer of device 0000:00:09.0 to 64 PCI: Setting latency timer of device 0000:00:0e.0 to 64 PCI: Bridge: 0000:08:0a.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:08:0b.0 IO window: 2000-2fff MEM window: d0100000-d04fffff PREFETCH window: b0200000-b03fffff PCI: Bridge: 0000:80:0e.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Setting latency timer of device 0000:80:0e.0 to 64 Simple Boot Flag at 0x36 set to 0x1 Machine check exception polling timer started. apm: BIOS not found. highmem bounce pool size: 64 pages Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NTFS driver 2.1.23 [Flags: R/W]. JFS: nTxBlock = 8192, nTxLock = 65536 Initializing Cryptographic API PCI: MSI quirk detected. pci_msi_quirk set. PCI: MSI quirk detected. pci_msi_quirk set. PCI: Setting latency timer of device 0000:00:0e.0 to 64 pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[pcie00] PCI: Setting latency timer of device 0000:80:0e.0 to 64 pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[pcie00] PNP: No PS/2 controller found. Probing ports directly. serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Probing IDE interface ide0... hda: SONY DVD RW DW-Q28A, ATAPI CD/DVD-ROM drive Probing IDE interface ide1... ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 libata version 1.12 loaded. sata_nv version 0.6 ACPI: PCI Interrupt Link [LTID] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LTID] -> GSI 23 (level, high) -> IRQ 16 PCI: Setting latency timer of device 0000:00:07.0 to 64 ata1: SATA max UDMA/133 cmd 0x1C40 ctl 0x1C36 bmdma 0x1C10 irq 16 ata2: SATA max UDMA/133 cmd 0x1C38 ctl 0x1C32 bmdma 0x1C18 irq 16 ata1: no device found (phy stat 00000000) scsi0 : sata_nv ata2: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3d01 87:4003 88:203f ata2: dev 0 ATA, max UDMA/100, 586072368 sectors: lba48 nv_sata: Primary device added nv_sata: Primary device removed nv_sata: Secondary device added nv_sata: Secondary device removed ata2: dev 0 configured for UDMA/100 scsi1 : sata_nv Vendor: ATA Model: WDC WD3000JD-00K Rev: 08.0 Type: Direct-Access ANSI SCSI revision: 05 ACPI: PCI Interrupt Link [LSI1] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LSI1] -> GSI 22 (level, high) -> IRQ 17 PCI: Setting latency timer of device 0000:00:08.0 to 64 ata3: SATA max UDMA/133 cmd 0x1C58 ctl 0x1C4E bmdma 0x1C20 irq 17 ata4: SATA max UDMA/133 cmd 0x1C50 ctl 0x1C4A bmdma 0x1C28 irq 17 ata3: no device found (phy stat 00000000) scsi2 : sata_nv ata4: no device found (phy stat 00000000) scsi3 : sata_nv SCSI device sda: 586072368 512-byte hdwr sectors (300069 MB) SCSI device sda: drive cache: write back SCSI device sda: 586072368 512-byte hdwr sectors (300069 MB) SCSI device sda: drive cache: write back sda: sda1 Attached scsi disk sda at scsi1, channel 0, id 0, lun 0 I2O subsystem v1.288 i2o: max drivers = 8 I2O Configuration OSM v1.248 I2O Bus Adapter OSM v$Rev$ I2O Block Device OSM v1.287 I2O SCSI Peripheral OSM v1.282 I2O ProcFS OSM v1.145 Fusion MPT base driver 3.03.02 Copyright (c) 1999-2005 LSI Logic Corporation Fusion MPT SPI Host driver 3.03.02 ACPI: PCI Interrupt 0000:0a:06.0[A] -> GSI 30 (level, low) -> IRQ 18 mptbase: Initiating ioc0 bringup ioc0: 53C1030: Capabilities={Initiator,Target} scsi4 : ioc0: LSI53C1030, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=18 Vendor: SEAGATE Model: ST373454LW Rev: 0003 Type: Direct-Access ANSI SCSI revision: 03 SCSI device sdb: 143374744 512-byte hdwr sectors (73408 MB) SCSI device sdb: drive cache: write back SCSI device sdb: 143374744 512-byte hdwr sectors (73408 MB) SCSI device sdb: drive cache: write back sdb: sdb1 sdb2 sdb3 sdb4 Attached scsi disk sdb at scsi4, channel 0, id 0, lun 0 ACPI: PCI Interrupt 0000:0a:06.1[B] -> GSI 31 (level, low) -> IRQ 19 mptbase: Initiating ioc1 bringup ioc1: 53C1030: Capabilities={Initiator,Target} scsi5 : ioc1: LSI53C1030, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=19 Fusion MPT FC Host driver 3.03.02 ohci1394: $Rev: 1299 $ Ben Collins <bcollins@debian.org> ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 19 ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNK4] -> GSI 19 (level, high) -> IRQ 20 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[b0104000-b01047ff] Max Packet=[2048] ieee1394: raw1394: /dev/raw1394 device initialized usbmon: debugfs is not available ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS2] -> GSI 21 (level, high) -> IRQ 21 PCI: Setting latency timer of device 0000:00:02.1 to 64 ehci_hcd 0000:00:02.1: EHCI Host Controller ehci_hcd 0000:00:02.1: debug port 1 ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e081000023a5ab] ehci_hcd 0000:00:02.1: BIOS handoff failed (160, 01010001) ehci_hcd 0000:00:02.1: continuing after BIOS bug... ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:02.1: irq 21, io mem 0xb0001000 PCI: cache line size of 64 is not supported by device 0000:00:02.1 ehci_hcd 0000:00:02.1: park 0 ehci_hcd 0000:00:02.1: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 1-0:1.0: USB hub found hub 1-0:1.0: 10 ports detected USB Universal Host Controller Interface driver v2.3 usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.01:USB HID core driver mice: PS/2 mouse device common for all mice NET: Registered protocol family 2 IP route cache hash table entries: 262144 (order: 8, 1048576 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 7, 786432 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered ip_conntrack version 2.1 (8192 buckets, 65536 max) - 212 bytes per conntrack input: AT Translated Set 2 keyboard on isa0060/serio0 ip_tables: (C) 2000-2002 Netfilter core team ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/ arp_tables: (C) 2002 David S. Miller TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Starting balanced_irq Using IPI Shortcut mode EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 212k freed kjournald starting. Commit interval 5 seconds EXT3 FS on sdb2, internal journal Linux agpgart interface v0.101 (c) Dave Jones ACPI: PCI Interrupt Link [LACI] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LACI] -> GSI 20 (level, high) -> IRQ 22 PCI: Setting latency timer of device 0000:00:04.0 to 64 AC'97 0 does not respond - RESET AC'97 0 access is not valid [0xffffffff], removing mixer. Unable to initialize codec #0 ACPI: PCI interrupt for device 0000:00:04.0 disabled Intel ICH: probe of 0000:00:04.0 failed with error -5 i2c_adapter i2c-0: nForce2 SMBus adapter at 0xa000 i2c_adapter i2c-1: nForce2 SMBus adapter at 0xa040
bugme-daemon@bugzilla.kernel.org wrote: > > http://bugzilla.kernel.org/show_bug.cgi?id=6060 > Thanks. Could I ask the acpi team to take a look at this regression, determine whether it's an ACPI problem or an mpt-fusion problem, or something else? I'd suspect acpi-interrupts.
Please try pci=noacpi
If 2.6.13 boots with "acpi=off", please try the "acpi=off" with 2.6.16. Please attach the output from lspci -vv. Please build both old and new kernels with CONFIG_PCI_MSI=n and report if you see a difference.
a) with pci=noacpi on 2.6.15 kernel there is no luck. (same results) b) with acpi=off under 2.6.13 the system does not boot, from the bootup sequence and device probing, it seems very similar to the sequence that fails under 2.6.15. (the LSI controller is not detected) c) Below you should see the lspci -vv using the 2.6.13.5 kernel d) CONFIG_PCI_MSI is not set on either kernels (I assume this is the same as having CONFIG_PCI_MSI=n) -- lspci -vv 00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [44] #08 [01e0] Capabilities: [e0] #08 [a801] 00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 0: I/O ports at <ignored> 00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 0 Region 0: I/O ports at 1000 [size=32] Region 4: I/O ports at a000 [size=64] Region 5: I/O ports at a040 [size=64] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 10 Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3) (prog-if 20 [EHCI]) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 21 Region 0: Memory at b0001000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] #0a [2098] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:04.0 Multimedia audio controller: nVidia Corporation CK804 AC'97 Audio Controller (rev a2) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 22 Region 0: I/O ports at 1800 [size=256] Region 1: I/O ports at 1400 [size=256] Region 2: Memory at b0002000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f2) (prog-if 8a [Master SecP PriP]) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Region 4: I/O ports at 1c00 [size=16] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO]) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 1c40 [size=8] Region 1: I/O ports at 1c34 [size=4] Region 2: I/O ports at 1c38 [size=8] Region 3: I/O ports at 1c30 [size=4] Region 4: I/O ports at 1c10 [size=16] Region 5: Memory at b0003000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO]) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at 1c58 [size=8] Region 1: I/O ports at 1c4c [size=4] Region 2: I/O ports at 1c50 [size=8] Region 3: I/O ports at 1c48 [size=4] Region 4: I/O ports at 1c20 [size=16] Region 5: Memory at b0004000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 Memory behind bridge: b0100000-b01fffff BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- 00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (250ns min, 5000ns max) Interrupt: pin A routed to IRQ 10 Region 0: Memory at b0005000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 1c60 [size=8] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 10 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 Memory behind bridge: b1000000-b2ffffff Prefetchable memory behind bridge: 00000000c0000000-00000000cff00000 BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [58] #08 [a800] Capabilities: [80] #10 [0141] 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Capabilities: [80] #08 [2101] Capabilities: [a0] #08 [2101] Capabilities: [c0] #08 [2101] 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Capabilities: [80] #08 [2101] Capabilities: [a0] #08 [2101] Capabilities: [c0] #08 [2101] 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- 01:05.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI]) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (500ns min, 1000ns max), cache line size 10 Interrupt: pin A routed to IRQ 20 Region 0: Memory at b0104000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at b0100000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME+ 02:00.0 VGA compatible controller: nVidia Corporation NV41 [Quadro FX 3450/4000 SDI] (rev a2) (prog-if 00 [VGA]) Subsystem: nVidia Corporation: Unknown device 029b Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 10 Interrupt: pin A routed to IRQ 5 Region 0: Memory at b2000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at b1000000 (64-bit, non-prefetchable) [size=16M] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [68] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [78] #10 [0001] 08:0a.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=08, secondary=09, subordinate=09, sec-latency=0 BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [a0] Capabilities: [b8] #08 [8000] Capabilities: [c0] #08 [004a] 08:0a.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01) (prog-if 10 [IO-APIC]) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 0: Memory at d0000000 (64-bit, non-prefetchable) [size=4K] 08:0b.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=08, secondary=0a, subordinate=0a, sec-latency=136 I/O behind bridge: 00002000-00002fff Memory behind bridge: d0100000-d04fffff Prefetchable memory behind bridge: 00000000b0200000-00000000b0300000 BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [a0] Capabilities: [b8] #08 [8000] 08:0b.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01) (prog-if 10 [IO-APIC]) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 0: Memory at d0001000 (64-bit, non-prefetchable) [size=4K] 0a:06.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 128 (4000ns min, 1500ns max), cache line size 10 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 2000 [size=256] Region 1: Memory at d0200000 (64-bit, non-prefetchable) [size=1M] Region 3: Memory at d0100000 (64-bit, non-prefetchable) [size=1M] Expansion ROM at b0200000 [disabled] [size=1M] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [68] 0a:06.1 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 128 (4000ns min, 1500ns max), cache line size 10 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at 2400 [size=256] Region 1: Memory at d0400000 (64-bit, non-prefetchable) [size=1M] Region 3: Memory at d0300000 (64-bit, non-prefetchable) [size=1M] Expansion ROM at b0300000 [disabled] [size=1M] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [68] 80:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [44] #08 [01e0] Capabilities: [e0] #08 [a801] 80:01.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 1: Memory at d0700000 (32-bit, non-prefetchable) [size=4K] 80:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3) Subsystem: Tyan Computer: Unknown device 2895 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (250ns min, 5000ns max) Interrupt: pin A routed to IRQ 5 Region 0: Memory at d0701000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 3000 [size=8] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 80:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, cache line size 10 Bus: primary=80, secondary=81, subordinate=81, sec-latency=0 BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [58] #08 [a800] Capabilities: [80] #10 [0141]
Can you turn on MPT_DEBUG_INIT in drivers/message/fusion/mptbase.h, i.e., add a line like #define MPT_DEBUG_INIT 1 at the beginning of the file? That should turn on some debug output when the driver claims and initializes the device. When it doesn't work, you're seeing: > Fusion MPT base driver 3.03.04 > Copyright (c) 1999-2005 LSI Logic Corporation > Fusion MPT SPI Host driver 3.03.04 > Fusion MPT FC Host driver 3.03.04 which suggests that mpt_attach() isn't even being called. The first thing mpt_attach() does is call pci_enable_device(), which is what prints the "ACPI: PCI Interrupt 0000:0a:06.0[A] -> GSI 30 (level, low) -> IRQ 18" message. Can you capture the failing dmesg with a serial console or netconsole?
For the 1030, all that is needed in .config is CONFIG_FUSION=y CONFIG_FUSION_SPI=y The CONFIG_FUSION_SAS is for SAS cards, and CONFIG_FUSION_FC is for Fibre Channel cards. And the CONFIG_FUSION_SPI is SCSI Parallel Interface, such as 1030. Per Bjorn Helgaas suggestion, all the debug defines can be enabled/disabled in the driver Makefile. They are all listed there. You will see DMPT_DEBUG_INIT in the MPT general section. In addition, pls can you enable DMPT_DEBUG_FAIL and DMPT_DEBUG_DEBUG. Redirect serial console pls, by passing console=ttyS0 from grub.
I modified the mptbase.h to enable debugging. On the 2.6.15 there is no more output coming out, which means I guess what you speculate of init functions not being called at all. In contrast the 2.6.13.5 provides a huge trail of extra information (I can provide that if it makes any difference). Unfortunately, I cannot at this time grab the boot sequence log of the kernel that crashes. I will look for a serial cable and attempt to capture it with a serial console.
Stathis - The function that brings up the card is in mptbase.c => mpt_attach(). You will see dinitprintk(), they get called when you enable MPT_DEBUG_INIT. You will see dprintk(), they get called when you enable MPT_DEBUG. Perhaps you could add some printk's your self to see where in this function your getting to. Pls enable the debug defines from the driver Makefile, and redirect cosole output to remote system.
Since you don't see any of the init debug output, it seems like the driver's probe() function (mptspi_probe()) isn't being called. But it doesn't look like anything in the driver (e.g., the table of PCI IDs that it claims) has changed. Can you add "#define DEBUG 1" as the first line of these files: drivers/base/bus.c drivers/base/dd.c drivers/pci/quirks.c and add "debug" to your kernel command line? The path should be mptspi_init pci_register_driver __pci_register_driver driver_register bus_add_driver driver_attach __driver_attach driver_probe_device mptspi_probe But it sounds like we're not making it all the way. Maybe there's a PCI quirk that hides the device, or maybe the device doesn't match the PCI ID table for some reason. The "lspci -vx" output for the LSI device might be useful.
Ok, I tried adding a few things on the mptbase.c file as well as enabled debugging support through the makefile. I now get "mptbase: Registered for IOC reset notification" and nothing else regarding mptbase, it then goes ahead with the other drivers. I traced this back in mptbase.c line 6392, not sure if that helps any. Next I did what Bjorn suggested, but the log is very long and I cannot see what it sais anymore. Because I think I'm throwing mud in your eyes without a log of the output, I will try to get a serial cable and come back with the output, but it has to wait until tomorrow, so as to make things easier for everyone. Please be patient and thanks for all the help so far.
Can you send me the source code that is failing, via private email. I've been posting many patch's in the patch month, so that is why I ask for yours. Eric Moore
Unfortunately, the null-modem cables are extinct around my area, I will need some more time to locate one. Would it be any different if I moved the filesystem on the SATA drive that is detected and boot temporarily from there? Then at least I will be able to send you the dmesg output.
> Would it be any different if I moved the filesystem on the SATA drive > that is detected and boot temporarily from there? That should be fine. Another approach would be to turn off the debug stuff I suggested and just manually add printks in the path I mentioned (starting in mptspi_probe() and working backwards). But moving the filesystem is probably easier for you. Thanks for all the work you're putting into this. We'll get it figured out eventually.
I moved my root filesystem onto the sata drive (/dev/sda), so now I can at least boot. Attached is the dmesg from the failing 2.6.15.4, where the controller does not get detected. The active changes are those of Eric in comment #11 and #14 regarding the debugging of the respective drivers. I am not sure if it is significant, but both kernels I build seem to be built as arch/i386, rather than x86_64 (considering where the make install of the kernel copies them from at least). This is I assume because my Slackware distribution is the i386 flavor and not a 64-bit. If this is relevant please let me know, but why would the older kernel works and the other doesn't. I also here attach my .config in case there is something wrong there too. # # Automatically generated make config: don't edit # Linux kernel version: 2.6.15.4 # Wed Feb 15 18:52:35 2006 # CONFIG_X86_32=y CONFIG_SEMAPHORE_SLEEPERS=y CONFIG_X86=y CONFIG_MMU=y CONFIG_UID16=y CONFIG_GENERIC_ISA_DMA=y CONFIG_GENERIC_IOMAP=y CONFIG_ARCH_MAY_HAVE_PC_FDC=y # # Code maturity level options # CONFIG_EXPERIMENTAL=y CONFIG_CLEAN_COMPILE=y CONFIG_LOCK_KERNEL=y CONFIG_INIT_ENV_ARG_LIMIT=32 # # General setup # CONFIG_LOCALVERSION="" CONFIG_LOCALVERSION_AUTO=y CONFIG_SWAP=y CONFIG_SYSVIPC=y CONFIG_POSIX_MQUEUE=y CONFIG_BSD_PROCESS_ACCT=y # CONFIG_BSD_PROCESS_ACCT_V3 is not set CONFIG_SYSCTL=y # CONFIG_AUDIT is not set CONFIG_HOTPLUG=y CONFIG_KOBJECT_UEVENT=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y # CONFIG_CPUSETS is not set CONFIG_INITRAMFS_SOURCE="" # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set # CONFIG_EMBEDDED is not set CONFIG_KALLSYMS=y # CONFIG_KALLSYMS_EXTRA_PASS is not set CONFIG_PRINTK=y CONFIG_BUG=y CONFIG_BASE_FULL=y CONFIG_FUTEX=y CONFIG_EPOLL=y CONFIG_SHMEM=y CONFIG_CC_ALIGN_FUNCTIONS=0 CONFIG_CC_ALIGN_LABELS=0 CONFIG_CC_ALIGN_LOOPS=0 CONFIG_CC_ALIGN_JUMPS=0 # CONFIG_TINY_SHMEM is not set CONFIG_BASE_SMALL=0 # # Loadable module support # CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y # CONFIG_MODULE_FORCE_UNLOAD is not set CONFIG_OBSOLETE_MODPARM=y # CONFIG_MODVERSIONS is not set # CONFIG_MODULE_SRCVERSION_ALL is not set CONFIG_KMOD=y CONFIG_STOP_MACHINE=y # # Block layer # CONFIG_LBD=y # # IO Schedulers # CONFIG_IOSCHED_NOOP=y CONFIG_IOSCHED_AS=y CONFIG_IOSCHED_DEADLINE=y CONFIG_IOSCHED_CFQ=y CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_DEADLINE is not set # CONFIG_DEFAULT_CFQ is not set # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" # # Processor type and features # CONFIG_X86_PC=y # CONFIG_X86_ELAN is not set # CONFIG_X86_VOYAGER is not set # CONFIG_X86_NUMAQ is not set # CONFIG_X86_SUMMIT is not set # CONFIG_X86_BIGSMP is not set # CONFIG_X86_VISWS is not set # CONFIG_X86_GENERICARCH is not set # CONFIG_X86_ES7000 is not set # CONFIG_M386 is not set # CONFIG_M486 is not set # CONFIG_M586 is not set # CONFIG_M586TSC is not set # CONFIG_M586MMX is not set # CONFIG_M686 is not set # CONFIG_MPENTIUMII is not set # CONFIG_MPENTIUMIII is not set # CONFIG_MPENTIUMM is not set # CONFIG_MPENTIUM4 is not set # CONFIG_MK6 is not set # CONFIG_MK7 is not set CONFIG_MK8=y # CONFIG_MCRUSOE is not set # CONFIG_MEFFICEON is not set # CONFIG_MWINCHIPC6 is not set # CONFIG_MWINCHIP2 is not set # CONFIG_MWINCHIP3D is not set # CONFIG_MGEODEGX1 is not set # CONFIG_MCYRIXIII is not set # CONFIG_MVIAC3_2 is not set # CONFIG_X86_GENERIC is not set CONFIG_X86_CMPXCHG=y CONFIG_X86_XADD=y CONFIG_X86_L1_CACHE_SHIFT=6 CONFIG_RWSEM_XCHGADD_ALGORITHM=y CONFIG_GENERIC_CALIBRATE_DELAY=y CONFIG_X86_WP_WORKS_OK=y CONFIG_X86_INVLPG=y CONFIG_X86_BSWAP=y CONFIG_X86_POPAD_OK=y CONFIG_X86_CMPXCHG64=y CONFIG_X86_GOOD_APIC=y CONFIG_X86_INTEL_USERCOPY=y CONFIG_X86_USE_PPRO_CHECKSUM=y CONFIG_X86_TSC=y # CONFIG_HPET_TIMER is not set CONFIG_SMP=y CONFIG_NR_CPUS=4 CONFIG_SCHED_SMT=y # CONFIG_PREEMPT_NONE is not set # CONFIG_PREEMPT_VOLUNTARY is not set CONFIG_PREEMPT=y CONFIG_PREEMPT_BKL=y CONFIG_X86_LOCAL_APIC=y CONFIG_X86_IO_APIC=y CONFIG_X86_MCE=y CONFIG_X86_MCE_NONFATAL=y # CONFIG_X86_MCE_P4THERMAL is not set # CONFIG_TOSHIBA is not set # CONFIG_I8K is not set CONFIG_X86_REBOOTFIXUPS=y # CONFIG_MICROCODE is not set CONFIG_X86_MSR=m CONFIG_X86_CPUID=m # # Firmware Drivers # # CONFIG_EDD is not set # CONFIG_DELL_RBU is not set # CONFIG_DCDBAS is not set # CONFIG_NOHIGHMEM is not set CONFIG_HIGHMEM4G=y # CONFIG_HIGHMEM64G is not set CONFIG_HIGHMEM=y CONFIG_SELECT_MEMORY_MODEL=y CONFIG_FLATMEM_MANUAL=y # CONFIG_DISCONTIGMEM_MANUAL is not set # CONFIG_SPARSEMEM_MANUAL is not set CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_HIGHPTE is not set # CONFIG_MATH_EMULATION is not set CONFIG_MTRR=y # CONFIG_EFI is not set CONFIG_IRQBALANCE=y # CONFIG_REGPARM is not set CONFIG_SECCOMP=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_1000 is not set CONFIG_HZ=250 CONFIG_PHYSICAL_START=0x100000 # CONFIG_KEXEC is not set # # Power management options (ACPI, APM) # CONFIG_PM=y CONFIG_PM_LEGACY=y # CONFIG_PM_DEBUG is not set # # ACPI (Advanced Configuration and Power Interface) Support # CONFIG_ACPI=y CONFIG_ACPI_AC=m CONFIG_ACPI_BATTERY=m CONFIG_ACPI_BUTTON=m CONFIG_ACPI_VIDEO=m # CONFIG_ACPI_HOTKEY is not set CONFIG_ACPI_FAN=m CONFIG_ACPI_PROCESSOR=m CONFIG_ACPI_THERMAL=m # CONFIG_ACPI_ASUS is not set # CONFIG_ACPI_IBM is not set # CONFIG_ACPI_TOSHIBA is not set CONFIG_ACPI_BLACKLIST_YEAR=0 # CONFIG_ACPI_DEBUG is not set CONFIG_ACPI_EC=y CONFIG_ACPI_POWER=y CONFIG_ACPI_SYSTEM=y CONFIG_X86_PM_TIMER=y # CONFIG_ACPI_CONTAINER is not set # # APM (Advanced Power Management) BIOS Support # CONFIG_APM=y # CONFIG_APM_IGNORE_USER_SUSPEND is not set # CONFIG_APM_DO_ENABLE is not set # CONFIG_APM_CPU_IDLE is not set # CONFIG_APM_DISPLAY_BLANK is not set # CONFIG_APM_RTC_IS_GMT is not set # CONFIG_APM_ALLOW_INTS is not set # CONFIG_APM_REAL_MODE_POWER_OFF is not set # # CPU Frequency scaling # # CONFIG_CPU_FREQ is not set # # Bus options (PCI, PCMCIA, EISA, MCA, ISA) # CONFIG_PCI=y # CONFIG_PCI_GOBIOS is not set # CONFIG_PCI_GOMMCONFIG is not set # CONFIG_PCI_GODIRECT is not set CONFIG_PCI_GOANY=y CONFIG_PCI_BIOS=y CONFIG_PCI_DIRECT=y CONFIG_PCI_MMCONFIG=y CONFIG_PCIEPORTBUS=y # CONFIG_PCI_MSI is not set CONFIG_PCI_LEGACY_PROC=y CONFIG_ISA_DMA_API=y # CONFIG_ISA is not set # CONFIG_MCA is not set # CONFIG_SCx200 is not set # CONFIG_HOTPLUG_CPU is not set # # PCCARD (PCMCIA/CardBus) support # # CONFIG_PCCARD is not set # # PCI Hotplug Support # # CONFIG_HOTPLUG_PCI is not set # # Executable file formats # CONFIG_BINFMT_ELF=y CONFIG_BINFMT_AOUT=y CONFIG_BINFMT_MISC=y # # Networking # CONFIG_NET=y # # Networking options # CONFIG_PACKET=y # CONFIG_PACKET_MMAP is not set CONFIG_UNIX=y # CONFIG_NET_KEY is not set CONFIG_INET=y CONFIG_IP_MULTICAST=y # CONFIG_IP_ADVANCED_ROUTER is not set CONFIG_IP_FIB_HASH=y # CONFIG_IP_PNP is not set # CONFIG_NET_IPIP is not set # CONFIG_NET_IPGRE is not set # CONFIG_IP_MROUTE is not set # CONFIG_ARPD is not set # CONFIG_SYN_COOKIES is not set # CONFIG_INET_AH is not set # CONFIG_INET_ESP is not set # CONFIG_INET_IPCOMP is not set # CONFIG_INET_TUNNEL is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_BIC=y # # IP: Virtual Server Configuration # # CONFIG_IP_VS is not set # CONFIG_IPV6 is not set CONFIG_NETFILTER=y # CONFIG_NETFILTER_DEBUG is not set # # Core Netfilter Configuration # # CONFIG_NETFILTER_NETLINK is not set # # IP: Netfilter Configuration # CONFIG_IP_NF_CONNTRACK=y # CONFIG_IP_NF_CT_ACCT is not set # CONFIG_IP_NF_CONNTRACK_MARK is not set # CONFIG_IP_NF_CONNTRACK_EVENTS is not set # CONFIG_IP_NF_CT_PROTO_SCTP is not set # CONFIG_IP_NF_FTP is not set # CONFIG_IP_NF_IRC is not set # CONFIG_IP_NF_NETBIOS_NS is not set # CONFIG_IP_NF_TFTP is not set # CONFIG_IP_NF_AMANDA is not set # CONFIG_IP_NF_PPTP is not set CONFIG_IP_NF_QUEUE=y CONFIG_IP_NF_IPTABLES=y CONFIG_IP_NF_MATCH_LIMIT=y CONFIG_IP_NF_MATCH_IPRANGE=y CONFIG_IP_NF_MATCH_MAC=y CONFIG_IP_NF_MATCH_PKTTYPE=y CONFIG_IP_NF_MATCH_MARK=y CONFIG_IP_NF_MATCH_MULTIPORT=y CONFIG_IP_NF_MATCH_TOS=y CONFIG_IP_NF_MATCH_RECENT=y CONFIG_IP_NF_MATCH_ECN=y CONFIG_IP_NF_MATCH_DSCP=y CONFIG_IP_NF_MATCH_AH_ESP=y CONFIG_IP_NF_MATCH_LENGTH=y CONFIG_IP_NF_MATCH_TTL=y CONFIG_IP_NF_MATCH_TCPMSS=y CONFIG_IP_NF_MATCH_HELPER=y CONFIG_IP_NF_MATCH_STATE=y CONFIG_IP_NF_MATCH_CONNTRACK=y CONFIG_IP_NF_MATCH_OWNER=y # CONFIG_IP_NF_MATCH_ADDRTYPE is not set # CONFIG_IP_NF_MATCH_REALM is not set # CONFIG_IP_NF_MATCH_SCTP is not set # CONFIG_IP_NF_MATCH_DCCP is not set # CONFIG_IP_NF_MATCH_COMMENT is not set # CONFIG_IP_NF_MATCH_HASHLIMIT is not set # CONFIG_IP_NF_MATCH_STRING is not set CONFIG_IP_NF_FILTER=y CONFIG_IP_NF_TARGET_REJECT=y CONFIG_IP_NF_TARGET_LOG=y CONFIG_IP_NF_TARGET_ULOG=y CONFIG_IP_NF_TARGET_TCPMSS=y # CONFIG_IP_NF_TARGET_NFQUEUE is not set CONFIG_IP_NF_NAT=y CONFIG_IP_NF_NAT_NEEDED=y CONFIG_IP_NF_TARGET_MASQUERADE=y CONFIG_IP_NF_TARGET_REDIRECT=y CONFIG_IP_NF_TARGET_NETMAP=y CONFIG_IP_NF_TARGET_SAME=y # CONFIG_IP_NF_NAT_SNMP_BASIC is not set CONFIG_IP_NF_MANGLE=y CONFIG_IP_NF_TARGET_TOS=y CONFIG_IP_NF_TARGET_ECN=y CONFIG_IP_NF_TARGET_DSCP=y CONFIG_IP_NF_TARGET_MARK=y CONFIG_IP_NF_TARGET_CLASSIFY=y # CONFIG_IP_NF_TARGET_TTL is not set CONFIG_IP_NF_RAW=m CONFIG_IP_NF_TARGET_NOTRACK=m CONFIG_IP_NF_ARPTABLES=y CONFIG_IP_NF_ARPFILTER=y CONFIG_IP_NF_ARP_MANGLE=y # # DCCP Configuration (EXPERIMENTAL) # # CONFIG_IP_DCCP is not set # # SCTP Configuration (EXPERIMENTAL) # # CONFIG_IP_SCTP is not set # CONFIG_ATM is not set # CONFIG_BRIDGE is not set # CONFIG_VLAN_8021Q is not set # CONFIG_DECNET is not set # CONFIG_LLC2 is not set # CONFIG_IPX is not set # CONFIG_ATALK is not set # CONFIG_X25 is not set # CONFIG_LAPB is not set # CONFIG_NET_DIVERT is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set # # QoS and/or fair queueing # # CONFIG_NET_SCHED is not set # # Network testing # # CONFIG_NET_PKTGEN is not set # CONFIG_HAMRADIO is not set # CONFIG_IRDA is not set # CONFIG_BT is not set # CONFIG_IEEE80211 is not set # # Device Drivers # # # Generic Driver Options # CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=m # # Connector - unified userspace <-> kernelspace linker # # CONFIG_CONNECTOR is not set # # Memory Technology Devices (MTD) # # CONFIG_MTD is not set # # Parallel port support # CONFIG_PARPORT=m CONFIG_PARPORT_PC=m CONFIG_PARPORT_SERIAL=m # CONFIG_PARPORT_PC_FIFO is not set # CONFIG_PARPORT_PC_SUPERIO is not set # CONFIG_PARPORT_GSC is not set CONFIG_PARPORT_1284=y # # Plug and Play support # CONFIG_PNP=y # CONFIG_PNP_DEBUG is not set # # Protocols # # CONFIG_PNPACPI is not set # # Block devices # CONFIG_BLK_DEV_FD=y # CONFIG_PARIDE is not set # CONFIG_BLK_CPQ_DA is not set # CONFIG_BLK_CPQ_CISS_DA is not set # CONFIG_BLK_DEV_DAC960 is not set # CONFIG_BLK_DEV_UMEM is not set # CONFIG_BLK_DEV_COW_COMMON is not set CONFIG_BLK_DEV_LOOP=y CONFIG_BLK_DEV_CRYPTOLOOP=m # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set # CONFIG_BLK_DEV_UB is not set # CONFIG_BLK_DEV_RAM is not set CONFIG_BLK_DEV_RAM_COUNT=16 # CONFIG_CDROM_PKTCDVD is not set # CONFIG_ATA_OVER_ETH is not set # # ATA/ATAPI/MFM/RLL support # CONFIG_IDE=y CONFIG_BLK_DEV_IDE=y # # Please see Documentation/ide.txt for help/info on IDE drives # # CONFIG_BLK_DEV_IDE_SATA is not set # CONFIG_BLK_DEV_HD_IDE is not set CONFIG_BLK_DEV_IDEDISK=y CONFIG_IDEDISK_MULTI_MODE=y CONFIG_BLK_DEV_IDECD=y # CONFIG_BLK_DEV_IDETAPE is not set # CONFIG_BLK_DEV_IDEFLOPPY is not set CONFIG_BLK_DEV_IDESCSI=y # CONFIG_IDE_TASK_IOCTL is not set # # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y # CONFIG_BLK_DEV_CMD640 is not set # CONFIG_BLK_DEV_IDEPNP is not set CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y # CONFIG_BLK_DEV_OFFBOARD is not set CONFIG_BLK_DEV_GENERIC=y # CONFIG_BLK_DEV_OPTI621 is not set CONFIG_BLK_DEV_RZ1000=y CONFIG_BLK_DEV_IDEDMA_PCI=y # CONFIG_BLK_DEV_IDEDMA_FORCED is not set CONFIG_IDEDMA_PCI_AUTO=y # CONFIG_IDEDMA_ONLYDISK is not set # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_BLK_DEV_ALI15X3 is not set # CONFIG_BLK_DEV_AMD74XX is not set # CONFIG_BLK_DEV_ATIIXP is not set # CONFIG_BLK_DEV_CMD64X is not set # CONFIG_BLK_DEV_TRIFLEX is not set # CONFIG_BLK_DEV_CY82C693 is not set # CONFIG_BLK_DEV_CS5520 is not set # CONFIG_BLK_DEV_CS5530 is not set # CONFIG_BLK_DEV_CS5535 is not set # CONFIG_BLK_DEV_HPT34X is not set # CONFIG_BLK_DEV_HPT366 is not set # CONFIG_BLK_DEV_SC1200 is not set # CONFIG_BLK_DEV_PIIX is not set # CONFIG_BLK_DEV_IT821X is not set # CONFIG_BLK_DEV_NS87415 is not set # CONFIG_BLK_DEV_PDC202XX_OLD is not set # CONFIG_BLK_DEV_PDC202XX_NEW is not set # CONFIG_BLK_DEV_SVWKS is not set # CONFIG_BLK_DEV_SIIMAGE is not set # CONFIG_BLK_DEV_SIS5513 is not set # CONFIG_BLK_DEV_SLC90E66 is not set # CONFIG_BLK_DEV_TRM290 is not set # CONFIG_BLK_DEV_VIA82CXXX is not set # CONFIG_IDE_ARM is not set CONFIG_BLK_DEV_IDEDMA=y # CONFIG_IDEDMA_IVB is not set CONFIG_IDEDMA_AUTO=y # CONFIG_BLK_DEV_HD is not set # # SCSI device support # # CONFIG_RAID_ATTRS is not set CONFIG_SCSI=y CONFIG_SCSI_PROC_FS=y # # SCSI support type (disk, tape, CD-ROM) # CONFIG_BLK_DEV_SD=y CONFIG_CHR_DEV_ST=m CONFIG_CHR_DEV_OSST=m CONFIG_BLK_DEV_SR=m CONFIG_BLK_DEV_SR_VENDOR=y CONFIG_CHR_DEV_SG=m # CONFIG_CHR_DEV_SCH is not set # # Some SCSI devices (e.g. CD jukebox) support multiple LUNs # # CONFIG_SCSI_MULTI_LUN is not set # CONFIG_SCSI_CONSTANTS is not set # CONFIG_SCSI_LOGGING is not set # # SCSI Transport Attributes # # CONFIG_SCSI_SPI_ATTRS is not set # CONFIG_SCSI_FC_ATTRS is not set CONFIG_SCSI_ISCSI_ATTRS=m CONFIG_SCSI_SAS_ATTRS=y # # SCSI low-level drivers # # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set # CONFIG_SCSI_3W_9XXX is not set # CONFIG_SCSI_ACARD is not set # CONFIG_SCSI_AACRAID is not set # CONFIG_SCSI_AIC7XXX is not set # CONFIG_SCSI_AIC7XXX_OLD is not set # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_DPT_I2O is not set CONFIG_MEGARAID_NEWGEN=y CONFIG_MEGARAID_MM=m CONFIG_MEGARAID_MAILBOX=m CONFIG_MEGARAID_SAS=m CONFIG_SCSI_SATA=y # CONFIG_SCSI_SATA_AHCI is not set # CONFIG_SCSI_SATA_SVW is not set # CONFIG_SCSI_ATA_PIIX is not set # CONFIG_SCSI_SATA_MV is not set CONFIG_SCSI_SATA_NV=y # CONFIG_SCSI_PDC_ADMA is not set # CONFIG_SCSI_SATA_QSTOR is not set # CONFIG_SCSI_SATA_PROMISE is not set # CONFIG_SCSI_SATA_SX4 is not set # CONFIG_SCSI_SATA_SIL is not set # CONFIG_SCSI_SATA_SIL24 is not set # CONFIG_SCSI_SATA_SIS is not set # CONFIG_SCSI_SATA_ULI is not set # CONFIG_SCSI_SATA_VIA is not set # CONFIG_SCSI_SATA_VITESSE is not set # CONFIG_SCSI_BUSLOGIC is not set # CONFIG_SCSI_DMX3191D is not set # CONFIG_SCSI_EATA is not set # CONFIG_SCSI_FUTURE_DOMAIN is not set # CONFIG_SCSI_GDTH is not set # CONFIG_SCSI_IPS is not set # CONFIG_SCSI_INITIO is not set # CONFIG_SCSI_INIA100 is not set # CONFIG_SCSI_PPA is not set # CONFIG_SCSI_IMM is not set # CONFIG_SCSI_SYM53C8XX_2 is not set # CONFIG_SCSI_IPR is not set # CONFIG_SCSI_QLOGIC_FC is not set # CONFIG_SCSI_QLOGIC_1280 is not set CONFIG_SCSI_QLA2XXX=y # CONFIG_SCSI_QLA21XX is not set # CONFIG_SCSI_QLA22XX is not set # CONFIG_SCSI_QLA2300 is not set # CONFIG_SCSI_QLA2322 is not set # CONFIG_SCSI_QLA6312 is not set # CONFIG_SCSI_QLA24XX is not set # CONFIG_SCSI_LPFC is not set # CONFIG_SCSI_DC395x is not set # CONFIG_SCSI_DC390T is not set # CONFIG_SCSI_NSP32 is not set # CONFIG_SCSI_DEBUG is not set # # Multi-device support (RAID and LVM) # CONFIG_MD=y CONFIG_BLK_DEV_MD=m CONFIG_MD_LINEAR=m CONFIG_MD_RAID0=m CONFIG_MD_RAID1=m CONFIG_MD_RAID10=m CONFIG_MD_RAID5=m CONFIG_MD_RAID6=m CONFIG_MD_MULTIPATH=m CONFIG_MD_FAULTY=m CONFIG_BLK_DEV_DM=m CONFIG_DM_CRYPT=m CONFIG_DM_SNAPSHOT=m CONFIG_DM_MIRROR=m CONFIG_DM_ZERO=m CONFIG_DM_MULTIPATH=m CONFIG_DM_MULTIPATH_EMC=m # # Fusion MPT device support # CONFIG_FUSION=y CONFIG_FUSION_SPI=y CONFIG_FUSION_FC=y CONFIG_FUSION_SAS=y CONFIG_FUSION_MAX_SGE=128 CONFIG_FUSION_CTL=y # # IEEE 1394 (FireWire) support # CONFIG_IEEE1394=y # # Subsystem Options # # CONFIG_IEEE1394_VERBOSEDEBUG is not set # CONFIG_IEEE1394_OUI_DB is not set # CONFIG_IEEE1394_EXTRA_CONFIG_ROMS is not set # CONFIG_IEEE1394_EXPORT_FULL_API is not set # # Device Drivers # # CONFIG_IEEE1394_PCILYNX is not set CONFIG_IEEE1394_OHCI1394=y # # Protocol Drivers # # CONFIG_IEEE1394_VIDEO1394 is not set # CONFIG_IEEE1394_SBP2 is not set # CONFIG_IEEE1394_ETH1394 is not set # CONFIG_IEEE1394_DV1394 is not set CONFIG_IEEE1394_RAWIO=y # CONFIG_IEEE1394_CMP is not set # # I2O device support # CONFIG_I2O=y CONFIG_I2O_EXT_ADAPTEC=y CONFIG_I2O_CONFIG=y CONFIG_I2O_CONFIG_OLD_IOCTL=y CONFIG_I2O_BUS=y CONFIG_I2O_BLOCK=y CONFIG_I2O_SCSI=y CONFIG_I2O_PROC=y # # Network device support # CONFIG_NETDEVICES=y CONFIG_DUMMY=m # CONFIG_BONDING is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set # CONFIG_NET_SB1000 is not set # # ARCnet devices # # CONFIG_ARCNET is not set # # PHY device support # # CONFIG_PHYLIB is not set # # Ethernet (10 or 100Mbit) # CONFIG_NET_ETHERNET=y CONFIG_MII=m # CONFIG_HAPPYMEAL is not set # CONFIG_SUNGEM is not set # CONFIG_CASSINI is not set # CONFIG_NET_VENDOR_3COM is not set # # Tulip family network device support # # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set # CONFIG_NET_PCI is not set # CONFIG_NET_POCKET is not set # # Ethernet (1000 Mbit) # # CONFIG_ACENIC is not set # CONFIG_DL2K is not set CONFIG_E1000=m # CONFIG_E1000_NAPI is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set # CONFIG_R8169 is not set # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SK98LIN is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set # # Ethernet (10000 Mbit) # # CONFIG_CHELSIO_T1 is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # # Token Ring devices # # CONFIG_TR is not set # # Wireless LAN (non-hamradio) # # CONFIG_NET_RADIO is not set # # Wan interfaces # # CONFIG_WAN is not set # CONFIG_FDDI is not set # CONFIG_HIPPI is not set # CONFIG_PLIP is not set # CONFIG_PPP is not set # CONFIG_SLIP is not set # CONFIG_NET_FC is not set # CONFIG_SHAPER is not set # CONFIG_NETCONSOLE is not set # CONFIG_NETPOLL is not set # CONFIG_NET_POLL_CONTROLLER is not set # # ISDN subsystem # # CONFIG_ISDN is not set # # Telephony Support # # CONFIG_PHONE is not set # # Input device support # CONFIG_INPUT=y # # Userland interfaces # CONFIG_INPUT_MOUSEDEV=y CONFIG_INPUT_MOUSEDEV_PSAUX=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set # CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set # # Input Device Drivers # CONFIG_INPUT_KEYBOARD=y CONFIG_KEYBOARD_ATKBD=y # CONFIG_KEYBOARD_SUNKBD is not set # CONFIG_KEYBOARD_LKKBD is not set # CONFIG_KEYBOARD_XTKBD is not set # CONFIG_KEYBOARD_NEWTON is not set CONFIG_INPUT_MOUSE=y CONFIG_MOUSE_PS2=y # CONFIG_MOUSE_SERIAL is not set # CONFIG_MOUSE_VSXXXAA is not set # CONFIG_INPUT_JOYSTICK is not set # CONFIG_INPUT_TOUCHSCREEN is not set # CONFIG_INPUT_MISC is not set # # Hardware I/O ports # CONFIG_SERIO=y CONFIG_SERIO_I8042=y # CONFIG_SERIO_SERPORT is not set # CONFIG_SERIO_CT82C710 is not set # CONFIG_SERIO_PARKBD is not set # CONFIG_SERIO_PCIPS2 is not set CONFIG_SERIO_LIBPS2=y # CONFIG_SERIO_RAW is not set # CONFIG_GAMEPORT is not set # # Character devices # CONFIG_VT=y CONFIG_VT_CONSOLE=y CONFIG_HW_CONSOLE=y # CONFIG_SERIAL_NONSTANDARD is not set # # Serial drivers # CONFIG_SERIAL_8250=y # CONFIG_SERIAL_8250_CONSOLE is not set # CONFIG_SERIAL_8250_ACPI is not set CONFIG_SERIAL_8250_NR_UARTS=4 # CONFIG_SERIAL_8250_EXTENDED is not set # # Non-8250 serial port support # CONFIG_SERIAL_CORE=y # CONFIG_SERIAL_JSM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 CONFIG_PRINTER=m # CONFIG_LP_CONSOLE is not set # CONFIG_PPDEV is not set # CONFIG_TIPAR is not set # # IPMI # # CONFIG_IPMI_HANDLER is not set # # Watchdog Cards # # CONFIG_WATCHDOG is not set CONFIG_HW_RANDOM=m # CONFIG_NVRAM is not set # CONFIG_RTC is not set # CONFIG_GEN_RTC is not set # CONFIG_DTLK is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set # CONFIG_SONYPI is not set # # Ftape, the floppy tape device driver # CONFIG_AGP=m # CONFIG_AGP_ALI is not set # CONFIG_AGP_ATI is not set # CONFIG_AGP_AMD is not set CONFIG_AGP_AMD64=m # CONFIG_AGP_INTEL is not set CONFIG_AGP_NVIDIA=m # CONFIG_AGP_SIS is not set # CONFIG_AGP_SWORKS is not set # CONFIG_AGP_VIA is not set # CONFIG_AGP_EFFICEON is not set CONFIG_DRM=m # CONFIG_DRM_TDFX is not set # CONFIG_DRM_R128 is not set # CONFIG_DRM_RADEON is not set # CONFIG_DRM_MGA is not set # CONFIG_DRM_SIS is not set # CONFIG_DRM_VIA is not set # CONFIG_DRM_SAVAGE is not set # CONFIG_MWAVE is not set # CONFIG_RAW_DRIVER is not set # CONFIG_HPET is not set # CONFIG_HANGCHECK_TIMER is not set # # TPM devices # # CONFIG_TCG_TPM is not set # CONFIG_TELCLOCK is not set # # I2C support # CONFIG_I2C=m CONFIG_I2C_CHARDEV=m # # I2C Algorithms # CONFIG_I2C_ALGOBIT=m # CONFIG_I2C_ALGOPCF is not set # CONFIG_I2C_ALGOPCA is not set # # I2C Hardware Bus support # # CONFIG_I2C_ALI1535 is not set # CONFIG_I2C_ALI1563 is not set # CONFIG_I2C_ALI15X3 is not set CONFIG_I2C_AMD756=m CONFIG_I2C_AMD756_S4882=m CONFIG_I2C_AMD8111=m # CONFIG_I2C_I801 is not set # CONFIG_I2C_I810 is not set # CONFIG_I2C_PIIX4 is not set CONFIG_I2C_NFORCE2=m # CONFIG_I2C_PARPORT is not set # CONFIG_I2C_PARPORT_LIGHT is not set # CONFIG_I2C_PROSAVAGE is not set # CONFIG_I2C_SAVAGE4 is not set # CONFIG_SCx200_ACB is not set # CONFIG_I2C_SIS5595 is not set # CONFIG_I2C_SIS630 is not set # CONFIG_I2C_SIS96X is not set CONFIG_I2C_STUB=m # CONFIG_I2C_VIA is not set # CONFIG_I2C_VIAPRO is not set # CONFIG_I2C_VOODOO3 is not set # CONFIG_I2C_PCA_ISA is not set # # Miscellaneous I2C Chip support # # CONFIG_SENSORS_DS1337 is not set # CONFIG_SENSORS_DS1374 is not set # CONFIG_SENSORS_EEPROM is not set # CONFIG_SENSORS_PCF8574 is not set # CONFIG_SENSORS_PCA9539 is not set # CONFIG_SENSORS_PCF8591 is not set # CONFIG_SENSORS_RTC8564 is not set # CONFIG_SENSORS_MAX6875 is not set # CONFIG_RTC_X1205_I2C is not set # CONFIG_I2C_DEBUG_CORE is not set # CONFIG_I2C_DEBUG_ALGO is not set # CONFIG_I2C_DEBUG_BUS is not set # CONFIG_I2C_DEBUG_CHIP is not set # # Dallas's 1-wire bus # # CONFIG_W1 is not set # # Hardware Monitoring support # CONFIG_HWMON=m # CONFIG_HWMON_VID is not set # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set # CONFIG_SENSORS_ADM1026 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set # CONFIG_SENSORS_ASB100 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set # CONFIG_SENSORS_FSCHER is not set # CONFIG_SENSORS_FSCPOS is not set # CONFIG_SENSORS_GL518SM is not set # CONFIG_SENSORS_GL520SM is not set # CONFIG_SENSORS_IT87 is not set # CONFIG_SENSORS_LM63 is not set # CONFIG_SENSORS_LM75 is not set # CONFIG_SENSORS_LM77 is not set # CONFIG_SENSORS_LM78 is not set # CONFIG_SENSORS_LM80 is not set # CONFIG_SENSORS_LM83 is not set # CONFIG_SENSORS_LM85 is not set # CONFIG_SENSORS_LM87 is not set # CONFIG_SENSORS_LM90 is not set # CONFIG_SENSORS_LM92 is not set # CONFIG_SENSORS_MAX1619 is not set # CONFIG_SENSORS_PC87360 is not set # CONFIG_SENSORS_SIS5595 is not set # CONFIG_SENSORS_SMSC47M1 is not set # CONFIG_SENSORS_SMSC47B397 is not set # CONFIG_SENSORS_VIA686A is not set # CONFIG_SENSORS_W83781D is not set # CONFIG_SENSORS_W83792D is not set # CONFIG_SENSORS_W83L785TS is not set # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_SENSORS_HDAPS is not set # CONFIG_HWMON_DEBUG_CHIP is not set # # Misc devices # # CONFIG_IBM_ASM is not set # # Multimedia Capabilities Port drivers # # # Multimedia devices # CONFIG_VIDEO_DEV=m # # Video For Linux # # # Video Adapters # # CONFIG_VIDEO_BT848 is not set # CONFIG_VIDEO_BWQCAM is not set # CONFIG_VIDEO_CQCAM is not set # CONFIG_VIDEO_W9966 is not set # CONFIG_VIDEO_CPIA is not set # CONFIG_VIDEO_SAA5246A is not set # CONFIG_VIDEO_SAA5249 is not set # CONFIG_TUNER_3036 is not set # CONFIG_VIDEO_STRADIS is not set # CONFIG_VIDEO_ZORAN is not set # CONFIG_VIDEO_SAA7134 is not set # CONFIG_VIDEO_MXB is not set # CONFIG_VIDEO_DPC is not set # CONFIG_VIDEO_HEXIUM_ORION is not set # CONFIG_VIDEO_HEXIUM_GEMINI is not set # CONFIG_VIDEO_CX88 is not set # CONFIG_VIDEO_EM28XX is not set # CONFIG_VIDEO_OVCAMCHIP is not set # CONFIG_VIDEO_AUDIO_DECODER is not set # CONFIG_VIDEO_DECODER is not set # # Radio Adapters # # CONFIG_RADIO_GEMTEK_PCI is not set # CONFIG_RADIO_MAXIRADIO is not set # CONFIG_RADIO_MAESTRO is not set # # Digital Video Broadcasting Devices # # CONFIG_DVB is not set # # Graphics support # CONFIG_FB=m CONFIG_FB_CFB_FILLRECT=m CONFIG_FB_CFB_COPYAREA=m CONFIG_FB_CFB_IMAGEBLIT=m # CONFIG_FB_MACMODES is not set CONFIG_FB_MODE_HELPERS=y # CONFIG_FB_TILEBLITTING is not set # CONFIG_FB_CIRRUS is not set # CONFIG_FB_PM2 is not set # CONFIG_FB_CYBER2000 is not set # CONFIG_FB_ARC is not set # CONFIG_FB_VGA16 is not set CONFIG_VIDEO_SELECT=y # CONFIG_FB_HGA is not set # CONFIG_FB_S1D13XXX is not set CONFIG_FB_NVIDIA=m CONFIG_FB_NVIDIA_I2C=y # CONFIG_FB_RIVA is not set # CONFIG_FB_I810 is not set # CONFIG_FB_INTEL is not set # CONFIG_FB_MATROX is not set # CONFIG_FB_RADEON_OLD is not set # CONFIG_FB_RADEON is not set # CONFIG_FB_ATY128 is not set # CONFIG_FB_ATY is not set # CONFIG_FB_SAVAGE is not set # CONFIG_FB_SIS is not set # CONFIG_FB_NEOMAGIC is not set # CONFIG_FB_KYRO is not set # CONFIG_FB_3DFX is not set # CONFIG_FB_VOODOO1 is not set # CONFIG_FB_CYBLA is not set # CONFIG_FB_TRIDENT is not set # CONFIG_FB_GEODE is not set # CONFIG_FB_VIRTUAL is not set # # Console display driver support # CONFIG_VGA_CONSOLE=y CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=m # CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set CONFIG_FONTS=y CONFIG_FONT_8x8=y CONFIG_FONT_8x16=y # CONFIG_FONT_6x11 is not set # CONFIG_FONT_7x14 is not set # CONFIG_FONT_PEARL_8x8 is not set # CONFIG_FONT_ACORN_8x8 is not set # CONFIG_FONT_MINI_4x6 is not set # CONFIG_FONT_SUN8x16 is not set # CONFIG_FONT_SUN12x22 is not set # CONFIG_FONT_10x18 is not set # # Logo configuration # # CONFIG_LOGO is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Sound # CONFIG_SOUND=m # # Advanced Linux Sound Architecture # CONFIG_SND=m CONFIG_SND_AC97_CODEC=m CONFIG_SND_AC97_BUS=m CONFIG_SND_TIMER=m CONFIG_SND_PCM=m CONFIG_SND_SEQUENCER=m # CONFIG_SND_SEQ_DUMMY is not set CONFIG_SND_OSSEMUL=y CONFIG_SND_MIXER_OSS=m CONFIG_SND_PCM_OSS=m CONFIG_SND_SEQUENCER_OSS=y # CONFIG_SND_VERBOSE_PRINTK is not set # CONFIG_SND_DEBUG is not set # # Generic devices # # CONFIG_SND_DUMMY is not set # CONFIG_SND_VIRMIDI is not set # CONFIG_SND_MTPAV is not set # CONFIG_SND_SERIAL_U16550 is not set # CONFIG_SND_MPU401 is not set # # PCI devices # # CONFIG_SND_ALI5451 is not set # CONFIG_SND_ATIIXP is not set # CONFIG_SND_ATIIXP_MODEM is not set # CONFIG_SND_AU8810 is not set # CONFIG_SND_AU8820 is not set # CONFIG_SND_AU8830 is not set # CONFIG_SND_AZT3328 is not set # CONFIG_SND_BT87X is not set # CONFIG_SND_CS46XX is not set # CONFIG_SND_CS4281 is not set # CONFIG_SND_EMU10K1 is not set # CONFIG_SND_EMU10K1X is not set # CONFIG_SND_CA0106 is not set # CONFIG_SND_KORG1212 is not set # CONFIG_SND_MIXART is not set # CONFIG_SND_NM256 is not set # CONFIG_SND_RME32 is not set # CONFIG_SND_RME96 is not set # CONFIG_SND_RME9652 is not set # CONFIG_SND_HDSP is not set # CONFIG_SND_HDSPM is not set # CONFIG_SND_TRIDENT is not set # CONFIG_SND_YMFPCI is not set # CONFIG_SND_AD1889 is not set # CONFIG_SND_ALS4000 is not set # CONFIG_SND_CMIPCI is not set # CONFIG_SND_ENS1370 is not set # CONFIG_SND_ENS1371 is not set # CONFIG_SND_ES1938 is not set # CONFIG_SND_ES1968 is not set # CONFIG_SND_MAESTRO3 is not set # CONFIG_SND_FM801 is not set # CONFIG_SND_ICE1712 is not set # CONFIG_SND_ICE1724 is not set CONFIG_SND_INTEL8X0=m # CONFIG_SND_INTEL8X0M is not set # CONFIG_SND_SONICVIBES is not set # CONFIG_SND_VIA82XX is not set # CONFIG_SND_VIA82XX_MODEM is not set # CONFIG_SND_VX222 is not set # CONFIG_SND_HDA_INTEL is not set # # USB devices # # CONFIG_SND_USB_AUDIO is not set # CONFIG_SND_USB_USX2Y is not set # # Open Sound System # # CONFIG_SOUND_PRIME is not set # # USB support # CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y CONFIG_USB=y # CONFIG_USB_DEBUG is not set # # Miscellaneous USB options # CONFIG_USB_DEVICEFS=y # CONFIG_USB_BANDWIDTH is not set # CONFIG_USB_DYNAMIC_MINORS is not set # CONFIG_USB_SUSPEND is not set # CONFIG_USB_OTG is not set # # USB Host Controller Drivers # CONFIG_USB_EHCI_HCD=y # CONFIG_USB_EHCI_SPLIT_ISO is not set # CONFIG_USB_EHCI_ROOT_HUB_TT is not set # CONFIG_USB_ISP116X_HCD is not set # CONFIG_USB_OHCI_HCD is not set CONFIG_USB_UHCI_HCD=y # CONFIG_USB_SL811_HCD is not set # # USB Device Class drivers # # CONFIG_OBSOLETE_OSS_USB_DRIVER is not set # CONFIG_USB_ACM is not set CONFIG_USB_PRINTER=y # # NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' # # # may also be needed; see USB_STORAGE Help for more information # CONFIG_USB_STORAGE=y # CONFIG_USB_STORAGE_DEBUG is not set # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set # CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_DPCM is not set # CONFIG_USB_STORAGE_USBAT is not set # CONFIG_USB_STORAGE_SDDR09 is not set # CONFIG_USB_STORAGE_SDDR55 is not set # CONFIG_USB_STORAGE_JUMPSHOT is not set # # USB Input Devices # CONFIG_USB_HID=y CONFIG_USB_HIDINPUT=y # CONFIG_HID_FF is not set # CONFIG_USB_HIDDEV is not set # CONFIG_USB_AIPTEK is not set # CONFIG_USB_WACOM is not set # CONFIG_USB_ACECAD is not set # CONFIG_USB_KBTAB is not set # CONFIG_USB_POWERMATE is not set # CONFIG_USB_MTOUCH is not set # CONFIG_USB_ITMTOUCH is not set CONFIG_USB_EGALAX=m # CONFIG_USB_YEALINK is not set # CONFIG_USB_XPAD is not set # CONFIG_USB_ATI_REMOTE is not set # CONFIG_USB_KEYSPAN_REMOTE is not set # CONFIG_USB_APPLETOUCH is not set # # USB Imaging devices # # CONFIG_USB_MDC800 is not set # CONFIG_USB_MICROTEK is not set # # USB Multimedia devices # # CONFIG_USB_DABUSB is not set # CONFIG_USB_VICAM is not set # CONFIG_USB_DSBR is not set # CONFIG_USB_IBMCAM is not set # CONFIG_USB_KONICAWC is not set # CONFIG_USB_OV511 is not set # CONFIG_USB_SE401 is not set # CONFIG_USB_SN9C102 is not set # CONFIG_USB_STV680 is not set # CONFIG_USB_PWC is not set # # USB Network Adapters # # CONFIG_USB_CATC is not set # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set # CONFIG_USB_USBNET is not set CONFIG_USB_MON=y # # USB port drivers # # CONFIG_USB_USS720 is not set # # USB Serial Converter support # # CONFIG_USB_SERIAL is not set # # USB Miscellaneous drivers # # CONFIG_USB_EMI62 is not set # CONFIG_USB_EMI26 is not set # CONFIG_USB_AUERSWALD is not set # CONFIG_USB_RIO500 is not set # CONFIG_USB_LEGOTOWER is not set # CONFIG_USB_LCD is not set # CONFIG_USB_LED is not set CONFIG_USB_CYTHERM=m # CONFIG_USB_PHIDGETKIT is not set CONFIG_USB_PHIDGETSERVO=m # CONFIG_USB_IDMOUSE is not set # CONFIG_USB_SISUSBVGA is not set # CONFIG_USB_LD is not set # CONFIG_USB_TEST is not set # # USB DSL modem support # # # USB Gadget Support # # CONFIG_USB_GADGET is not set # # MMC/SD Card support # # CONFIG_MMC is not set # # InfiniBand support # # CONFIG_INFINIBAND is not set # # SN Devices # # # File systems # CONFIG_EXT2_FS=y # CONFIG_EXT2_FS_XATTR is not set # CONFIG_EXT2_FS_XIP is not set CONFIG_EXT3_FS=y CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_POSIX_ACL is not set # CONFIG_EXT3_FS_SECURITY is not set CONFIG_JBD=y # CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y CONFIG_REISERFS_FS=y # CONFIG_REISERFS_CHECK is not set # CONFIG_REISERFS_PROC_INFO is not set # CONFIG_REISERFS_FS_XATTR is not set CONFIG_JFS_FS=y CONFIG_JFS_POSIX_ACL=y # CONFIG_JFS_SECURITY is not set # CONFIG_JFS_DEBUG is not set # CONFIG_JFS_STATISTICS is not set CONFIG_FS_POSIX_ACL=y # CONFIG_XFS_FS is not set # CONFIG_MINIX_FS is not set # CONFIG_ROMFS_FS is not set CONFIG_INOTIFY=y # CONFIG_QUOTA is not set CONFIG_DNOTIFY=y CONFIG_AUTOFS_FS=y CONFIG_AUTOFS4_FS=y # CONFIG_FUSE_FS is not set # # CD-ROM/DVD Filesystems # CONFIG_ISO9660_FS=y CONFIG_JOLIET=y # CONFIG_ZISOFS is not set CONFIG_UDF_FS=y CONFIG_UDF_NLS=y # # DOS/FAT/NT Filesystems # CONFIG_FAT_FS=y CONFIG_MSDOS_FS=y CONFIG_VFAT_FS=y CONFIG_FAT_DEFAULT_CODEPAGE=437 CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" CONFIG_NTFS_FS=y # CONFIG_NTFS_DEBUG is not set CONFIG_NTFS_RW=y # # Pseudo filesystems # CONFIG_PROC_FS=y CONFIG_PROC_KCORE=y CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_HUGETLBFS is not set # CONFIG_HUGETLB_PAGE is not set CONFIG_RAMFS=y # CONFIG_RELAYFS_FS is not set # # Miscellaneous filesystems # # CONFIG_ADFS_FS is not set # CONFIG_AFFS_FS is not set # CONFIG_HFS_FS is not set # CONFIG_HFSPLUS_FS is not set # CONFIG_BEFS_FS is not set # CONFIG_BFS_FS is not set # CONFIG_EFS_FS is not set # CONFIG_CRAMFS is not set # CONFIG_VXFS_FS is not set # CONFIG_HPFS_FS is not set # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set # # Network File Systems # CONFIG_NFS_FS=y # CONFIG_NFS_V3 is not set # CONFIG_NFS_V4 is not set # CONFIG_NFS_DIRECTIO is not set CONFIG_NFSD=y # CONFIG_NFSD_V3 is not set CONFIG_NFSD_TCP=y CONFIG_LOCKD=y CONFIG_EXPORTFS=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set # CONFIG_SMB_FS is not set # CONFIG_CIFS is not set # CONFIG_NCP_FS is not set # CONFIG_CODA_FS is not set # CONFIG_AFS_FS is not set # CONFIG_9P_FS is not set # # Partition Types # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y # # Native Language Support # CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=y # CONFIG_NLS_CODEPAGE_737 is not set # CONFIG_NLS_CODEPAGE_775 is not set # CONFIG_NLS_CODEPAGE_850 is not set # CONFIG_NLS_CODEPAGE_852 is not set # CONFIG_NLS_CODEPAGE_855 is not set # CONFIG_NLS_CODEPAGE_857 is not set # CONFIG_NLS_CODEPAGE_860 is not set # CONFIG_NLS_CODEPAGE_861 is not set # CONFIG_NLS_CODEPAGE_862 is not set # CONFIG_NLS_CODEPAGE_863 is not set # CONFIG_NLS_CODEPAGE_864 is not set # CONFIG_NLS_CODEPAGE_865 is not set # CONFIG_NLS_CODEPAGE_866 is not set # CONFIG_NLS_CODEPAGE_869 is not set # CONFIG_NLS_CODEPAGE_936 is not set # CONFIG_NLS_CODEPAGE_950 is not set # CONFIG_NLS_CODEPAGE_932 is not set # CONFIG_NLS_CODEPAGE_949 is not set # CONFIG_NLS_CODEPAGE_874 is not set # CONFIG_NLS_ISO8859_8 is not set # CONFIG_NLS_CODEPAGE_1250 is not set # CONFIG_NLS_CODEPAGE_1251 is not set # CONFIG_NLS_ASCII is not set CONFIG_NLS_ISO8859_1=y # CONFIG_NLS_ISO8859_2 is not set # CONFIG_NLS_ISO8859_3 is not set # CONFIG_NLS_ISO8859_4 is not set # CONFIG_NLS_ISO8859_5 is not set # CONFIG_NLS_ISO8859_6 is not set # CONFIG_NLS_ISO8859_7 is not set # CONFIG_NLS_ISO8859_9 is not set # CONFIG_NLS_ISO8859_13 is not set # CONFIG_NLS_ISO8859_14 is not set # CONFIG_NLS_ISO8859_15 is not set # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_UTF8 is not set # # Instrumentation Support # # CONFIG_PROFILING is not set # CONFIG_KPROBES is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set # CONFIG_DEBUG_KERNEL is not set CONFIG_LOG_BUF_SHIFT=15 CONFIG_DEBUG_BUGVERBOSE=y CONFIG_EARLY_PRINTK=y CONFIG_X86_FIND_SMP_CONFIG=y CONFIG_X86_MPPARSE=y # # Security options # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set # # Cryptographic options # CONFIG_CRYPTO=y # CONFIG_CRYPTO_HMAC is not set # CONFIG_CRYPTO_NULL is not set # CONFIG_CRYPTO_MD4 is not set # CONFIG_CRYPTO_MD5 is not set # CONFIG_CRYPTO_SHA1 is not set # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set # CONFIG_CRYPTO_WP512 is not set # CONFIG_CRYPTO_TGR192 is not set # CONFIG_CRYPTO_DES is not set # CONFIG_CRYPTO_BLOWFISH is not set # CONFIG_CRYPTO_TWOFISH is not set # CONFIG_CRYPTO_SERPENT is not set # CONFIG_CRYPTO_AES_586 is not set # CONFIG_CRYPTO_CAST5 is not set # CONFIG_CRYPTO_CAST6 is not set # CONFIG_CRYPTO_TEA is not set # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_TEST is not set # # Hardware crypto devices # # CONFIG_CRYPTO_DEV_PADLOCK is not set # # Library routines # # CONFIG_CRC_CCITT is not set # CONFIG_CRC16 is not set CONFIG_CRC32=y CONFIG_LIBCRC32C=m CONFIG_GENERIC_HARDIRQS=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_GENERIC_PENDING_IRQ=y CONFIG_X86_SMP=y CONFIG_X86_HT=y CONFIG_X86_BIOS_REBOOT=y CONFIG_X86_TRAMPOLINE=y Linux version 2.6.15.4 (root@darkstar) (gcc version 3.3.6) #2 SMP PREEMPT Wed Feb 15 19:42:46 CET 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009ac00 (usable) BIOS-e820: 000000000009ac00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000da000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007ff90000 (usable) BIOS-e820: 000000007ff90000 - 000000007ff97000 (ACPI data) BIOS-e820: 000000007ff97000 - 0000000080000000 (ACPI NVS) BIOS-e820: 0000000080000000 - 00000000aff80000 (usable) BIOS-e820: 00000000aff80000 - 00000000b0000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec00400 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) BIOS-e820: 0000000100000000 - 0000000150000000 (usable) Warning only 4GB will be used. Use a PAE enabled kernel. 3200MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000f7950 On node 0 totalpages: 1048576 DMA zone: 4096 pages, LIFO batch:0 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 225280 pages, LIFO batch:31 HighMem zone: 819200 pages, LIFO batch:31 DMI present. ACPI: RSDP (v000 PTLTD ) @ 0x000f7920 ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x7ff926a5 ACPI: FADT (v001 NVIDIA CK8S 0x06040000 PTL_ 0x000f4240) @ 0x7ff96c90 ACPI: SRAT (v001 AMD HAMMER 0x06040000 AMD 0x00000001) @ 0x7ff96d04 ACPI: SPCR (v001 PTLTD $UCRTBL$ 0x06040000 PTL 0x00000001) @ 0x7ff96e14 ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x7ff96e64 ACPI: MCFG (v001 PTLTD MCFG 0x06040000 LTP 0x00000000) @ 0x7ff96f00 ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x7ff96f3c ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x7ff96fd8 ACPI: DSDT (v001 NVIDIA CK8 0x06040000 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x8008 ACPI: Local APIC address 0xfee00000 ACPI: 2 duplicate APIC table ignored. ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:1 APIC version 16 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 15:1 APIC version 16 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) Processor #2 15:1 APIC version 16 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled) Processor #3 15:1 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x05] address[0xd0000000] gsi_base[24]) IOAPIC[1]: apic_id 5, version 17, address 0xd0000000, GSI 24-27 ACPI: IOAPIC (id[0x06] address[0xd0001000] gsi_base[28]) IOAPIC[2]: apic_id 6, version 17, address 0xd0001000, GSI 28-31 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) ACPI: BIOS IRQ0 pin2 override ignored. ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 3 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at b4000000 (gap: b0000000:30000000) Built 1 zonelists Kernel command line: auto BOOT_IMAGE=2.6.15.4n ro root=801 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) mapped IOAPIC to ffffb000 (d0000000) mapped IOAPIC to ffffa000 (d0001000) Initializing CPU#0 PID hash table entries: 4096 (order: 12, 65536 bytes) Detected 2411.308 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 2838896k/4194304k available (3130k kernel code, 42508k reserved, 971k data, 224k init, 1965120k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 4827.47 BogoMIPS (lpj=9654959) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: After vendor identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 0(2) -> Core 0 CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000010 00000001 00000000 00000003 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. mtrr: v2.0 (20020519) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. CPU0: AMD Dual Core AMD Opteron(tm) Processor 280 stepping 02 Booting processor 1/1 eip 2000 Initializing CPU#1 Calibrating delay using timer specific routine.. 4822.62 BogoMIPS (lpj=9645252) CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: After vendor identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 1(2) -> Core 1 CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000010 00000001 00000000 00000003 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: AMD Dual Core AMD Opteron(tm) Processor 280 stepping 02 Booting processor 2/2 eip 2000 Initializing CPU#2 Calibrating delay using timer specific routine.. 4822.60 BogoMIPS (lpj=9645203) CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: After vendor identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 2(2) -> Core 1 CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000010 00000001 00000000 00000003 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#2. CPU2: AMD Dual Core AMD Opteron(tm) Processor 280 stepping 02 Booting processor 3/3 eip 2000 Initializing CPU#3 Calibrating delay using timer specific routine.. 4822.65 BogoMIPS (lpj=9645303) CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: After vendor identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 3(2) -> Core 1 CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000010 00000001 00000000 00000003 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#3. CPU3: AMD Dual Core AMD Opteron(tm) Processor 280 stepping 02 Total of 4 processors activated (19295.35 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 checking TSC synchronization across 4 CPUs: passed. Brought up 4 CPUs bus type 'platform' registered NET: Registered protocol family 16 bus type 'pci' registered ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd6b0, last bus=129 PCI: Using MMCONFIG ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI: Calling quirk c029e9d0 for 0000:00:00.0 PCI: Calling quirk c0388a70 for 0000:00:00.0 PCI: Calling quirk c0388e30 for 0000:00:00.0 PCI: Calling quirk c029e9d0 for 0000:00:01.0 PCI: Calling quirk c0388a70 for 0000:00:01.0 PCI: Calling quirk c0388e30 for 0000:00:01.0 PCI: Calling quirk c029e9d0 for 0000:00:01.1 PCI: Calling quirk c0388a70 for 0000:00:01.1 PCI: Calling quirk c0388e30 for 0000:00:01.1 PCI: Calling quirk c029e9d0 for 0000:00:02.0 PCI: Calling quirk c0388a70 for 0000:00:02.0 PCI: Calling quirk c0388e30 for 0000:00:02.0 PCI: Calling quirk c029e9d0 for 0000:00:02.1 PCI: Calling quirk c0388a70 for 0000:00:02.1 PCI: Calling quirk c0388e30 for 0000:00:02.1 PCI: Calling quirk c029e9d0 for 0000:00:04.0 PCI: Calling quirk c0388a70 for 0000:00:04.0 PCI: Calling quirk c0388e30 for 0000:00:04.0 PCI: Calling quirk c029e9d0 for 0000:00:06.0 PCI: Calling quirk c0388a70 for 0000:00:06.0 PCI: Calling quirk c0388e30 for 0000:00:06.0 PCI: Calling quirk c029e9d0 for 0000:00:07.0 PCI: Calling quirk c0388a70 for 0000:00:07.0 PCI: Calling quirk c0388e30 for 0000:00:07.0 PCI: Calling quirk c029e9d0 for 0000:00:08.0 PCI: Calling quirk c0388a70 for 0000:00:08.0 PCI: Calling quirk c0388e30 for 0000:00:08.0 PCI: Calling quirk c029e9d0 for 0000:00:09.0 PCI: Calling quirk c0388a70 for 0000:00:09.0 PCI: Calling quirk c0388e30 for 0000:00:09.0 PCI: Calling quirk c029e9d0 for 0000:00:0a.0 PCI: Calling quirk c0388a70 for 0000:00:0a.0 PCI: Calling quirk c0388e30 for 0000:00:0a.0 PCI: Calling quirk c029e9d0 for 0000:00:0e.0 PCI: Calling quirk c0388a70 for 0000:00:0e.0 PCI: Calling quirk c0388e30 for 0000:00:0e.0 PCI: Calling quirk c029e9d0 for 0000:00:18.0 PCI: Calling quirk c0388a70 for 0000:00:18.0 PCI: Calling quirk c0388e30 for 0000:00:18.0 PCI: Calling quirk c029e9d0 for 0000:00:18.1 PCI: Calling quirk c0388a70 for 0000:00:18.1 PCI: Calling quirk c0388e30 for 0000:00:18.1 PCI: Calling quirk c029e9d0 for 0000:00:18.2 PCI: Calling quirk c0388a70 for 0000:00:18.2 PCI: Calling quirk c0388e30 for 0000:00:18.2 PCI: Calling quirk c029e9d0 for 0000:00:18.3 PCI: Calling quirk c0388a70 for 0000:00:18.3 PCI: Calling quirk c0388e30 for 0000:00:18.3 PCI: Calling quirk c029e9d0 for 0000:00:19.0 PCI: Calling quirk c0388a70 for 0000:00:19.0 PCI: Calling quirk c0388e30 for 0000:00:19.0 PCI: Calling quirk c029e9d0 for 0000:00:19.1 PCI: Calling quirk c0388a70 for 0000:00:19.1 PCI: Calling quirk c0388e30 for 0000:00:19.1 PCI: Calling quirk c029e9d0 for 0000:00:19.2 PCI: Calling quirk c0388a70 for 0000:00:19.2 PCI: Calling quirk c0388e30 for 0000:00:19.2 PCI: Calling quirk c029e9d0 for 0000:00:19.3 PCI: Calling quirk c0388a70 for 0000:00:19.3 PCI: Calling quirk c0388e30 for 0000:00:19.3 PCI: Calling quirk c029e9d0 for 0000:01:05.0 PCI: Calling quirk c0388a70 for 0000:01:05.0 PCI: Calling quirk c0388e30 for 0000:01:05.0 PCI: Transparent bridge - 0000:00:09.0 PCI: Calling quirk c029e9d0 for 0000:02:00.0 PCI: Calling quirk c0388a70 for 0000:02:00.0 PCI: Calling quirk c0388e30 for 0000:02:00.0 Boot video device is 0000:02:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] bus pci: add device 0000:00:00.0 bus pci: add device 0000:00:01.0 bus pci: add device 0000:00:01.1 bus pci: add device 0000:00:02.0 bus pci: add device 0000:00:02.1 bus pci: add device 0000:00:04.0 bus pci: add device 0000:00:06.0 bus pci: add device 0000:00:07.0 bus pci: add device 0000:00:08.0 bus pci: add device 0000:00:09.0 bus pci: add device 0000:00:0a.0 bus pci: add device 0000:00:0e.0 bus pci: add device 0000:00:18.0 bus pci: add device 0000:00:18.1 bus pci: add device 0000:00:18.2 bus pci: add device 0000:00:18.3 bus pci: add device 0000:00:19.0 bus pci: add device 0000:00:19.1 bus pci: add device 0000:00:19.2 bus pci: add device 0000:00:19.3 bus pci: add device 0000:01:05.0 bus pci: add device 0000:02:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LNK3] (IRQs 16 17 18 19) *0 ACPI: PCI Interrupt Link [LNK4] (IRQs 16 17 18 19) *0 ACPI: PCI Interrupt Link [LNK5] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LSI1] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Root Bridge [PCI2] (0000:08) PCI: Probing PCI hardware (bus 08) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 ACPI: PCI Root Bridge [PCI1] (0000:80) PCI: Probing PCI hardware (bus 80) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI: Calling quirk c029e9d0 for 0000:80:00.0 PCI: Calling quirk c0388a70 for 0000:80:00.0 PCI: Calling quirk c0388e30 for 0000:80:00.0 PCI: Calling quirk c029e9d0 for 0000:80:01.0 PCI: Calling quirk c0388a70 for 0000:80:01.0 PCI: Calling quirk c0388e30 for 0000:80:01.0 PCI: Calling quirk c029e9d0 for 0000:80:0a.0 PCI: Calling quirk c0388a70 for 0000:80:0a.0 PCI: Calling quirk c0388e30 for 0000:80:0a.0 PCI: Calling quirk c029e9d0 for 0000:80:0e.0 PCI: Calling quirk c0388a70 for 0000:80:0e.0 PCI: Calling quirk c0388e30 for 0000:80:0e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT] bus pci: add device 0000:80:00.0 bus pci: add device 0000:80:01.0 bus pci: add device 0000:80:0a.0 bus pci: add device 0000:80:0e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.XVR0._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay bus type 'pnp' registered bus type 'scsi' registered SCSI subsystem initialized bus type 'usb' registered bus usb: add driver usbfs usbcore: registered new driver usbfs bus usb: add driver hub usbcore: registered new driver hub bus usb: add driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report bus pnp: add driver system PCI: Bridge: 0000:00:09.0 IO window: disabled. MEM window: b0100000-b01fffff PREFETCH window: disabled. PCI: Failed to allocate mem resource #6:20000@d0000000 for 0000:02:00.0 PCI: Bridge: 0000:00:0e.0 IO window: disabled. MEM window: b1000000-b2ffffff PREFETCH window: c0000000-cfffffff PCI: Setting latency timer of device 0000:00:09.0 to 64 PCI: Setting latency timer of device 0000:00:0e.0 to 64 PCI: Bridge: 0000:80:0e.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Setting latency timer of device 0000:80:0e.0 to 64 Simple Boot Flag at 0x36 set to 0x1 Machine check exception polling timer started. apm: BIOS not found. highmem bounce pool size: 64 pages Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NTFS driver 2.1.25 [Flags: R/W]. JFS: nTxBlock = 8192, nTxLock = 65536 Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered PCI: Calling quirk c029e890 for 0000:00:00.0 PCI: Calling quirk c0369f10 for 0000:00:00.0 PCI: Calling quirk c029e890 for 0000:80:00.0 PCI: Calling quirk c0369f10 for 0000:80:00.0 PCI: Calling quirk c029e890 for 0000:00:01.0 PCI: Calling quirk c0369f10 for 0000:00:01.0 PCI: Calling quirk c029e890 for 0000:00:01.1 PCI: Calling quirk c0369f10 for 0000:00:01.1 PCI: Calling quirk c029e890 for 0000:00:02.0 PCI: Calling quirk c0369f10 for 0000:00:02.0 PCI: Calling quirk c029e890 for 0000:00:02.1 PCI: Calling quirk c0369f10 for 0000:00:02.1 PCI: Calling quirk c029e890 for 0000:00:04.0 PCI: Calling quirk c0369f10 for 0000:00:04.0 PCI: Calling quirk c029e890 for 0000:00:06.0 PCI: Calling quirk c0369f10 for 0000:00:06.0 PCI: Calling quirk c029e890 for 0000:00:07.0 PCI: Calling quirk c0369f10 for 0000:00:07.0 PCI: Calling quirk c029e890 for 0000:00:08.0 PCI: Calling quirk c0369f10 for 0000:00:08.0 PCI: Calling quirk c029e890 for 0000:00:09.0 PCI: Calling quirk c0369f10 for 0000:00:09.0 PCI: Calling quirk c029e890 for 0000:00:0a.0 PCI: Calling quirk c0369f10 for 0000:00:0a.0 PCI: Calling quirk c029e890 for 0000:80:0a.0 PCI: Calling quirk c0369f10 for 0000:80:0a.0 PCI: Calling quirk c029e890 for 0000:00:0e.0 PCI: Calling quirk c0369f10 for 0000:00:0e.0 PCI: Calling quirk c029e890 for 0000:80:0e.0 PCI: Calling quirk c0369f10 for 0000:80:0e.0 PCI: Calling quirk c029e890 for 0000:00:18.0 PCI: Calling quirk c0369f10 for 0000:00:18.0 PCI: Calling quirk c029e890 for 0000:00:19.0 PCI: Calling quirk c0369f10 for 0000:00:19.0 PCI: Calling quirk c029e890 for 0000:00:18.1 PCI: Calling quirk c0369f10 for 0000:00:18.1 PCI: Calling quirk c029e890 for 0000:00:19.1 PCI: Calling quirk c0369f10 for 0000:00:19.1 PCI: Calling quirk c029e890 for 0000:00:18.2 PCI: Calling quirk c0369f10 for 0000:00:18.2 PCI: Calling quirk c029e890 for 0000:00:19.2 PCI: Calling quirk c0369f10 for 0000:00:19.2 PCI: Calling quirk c029e890 for 0000:00:18.3 PCI: Calling quirk c0369f10 for 0000:00:18.3 PCI: Calling quirk c029e890 for 0000:00:19.3 PCI: Calling quirk c0369f10 for 0000:00:19.3 PCI: Calling quirk c029e890 for 0000:01:05.0 PCI: Calling quirk c0369f10 for 0000:01:05.0 PCI: Calling quirk c029e890 for 0000:02:00.0 PCI: Calling quirk c0369f10 for 0000:02:00.0 PCI: Calling quirk c029e890 for 0000:80:01.0 PCI: Calling quirk c0369f10 for 0000:80:01.0 bus type 'pci_express' registered bus pci: add driver pcieport-driver pci: Matched Device 0000:00:0e.0 with Driver pcieport-driver PCI: Setting latency timer of device 0000:00:0e.0 to 64 pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[pcie00] bus pci_express: add device pcie00 Allocate Port Service[pcie03] bus pci_express: add device pcie03 bound device '0000:00:0e.0' to driver 'pcieport-driver' pci: Bound Device 0000:00:0e.0 to Driver pcieport-driver pci: Matched Device 0000:80:0e.0 with Driver pcieport-driver PCI: Setting latency timer of device 0000:80:0e.0 to 64 pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[pcie00] bus pci_express: add device pcie00 Allocate Port Service[pcie03] bus pci_express: add device pcie03 bound device '0000:80:0e.0' to driver 'pcieport-driver' pci: Bound Device 0000:80:0e.0 to Driver pcieport-driver bus type 'serio' registered bus pnp: add driver i8042 kbd bus pnp: add driver i8042 aux bus pnp: remove driver i8042 kbd bus pnp: remove driver i8042 aux PNP: No PS/2 controller found. Probing ports directly. bus platform: add driver i8042 bus platform: add device i8042 platform: Matched Device i8042 with Driver i8042 bound device 'i8042' to driver 'i8042' platform: Bound Device i8042 to Driver i8042 serio: i8042 AUX port at 0x60,0x64 irq 12 bus serio: add device serio0 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled bus serio: add device serio1 bus platform: add device serial8250 serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A bus platform: add driver serial8250 platform: Matched Device serial8250 with Driver serial8250 bound device 'serial8250' to driver 'serial8250' platform: Bound Device serial8250 to Driver serial8250 bus pnp: add driver serial bus pci: add driver serial Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 bus platform: add device floppy.0 loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx bus type 'ide' registered bus pci: add driver RZ1000_IDE bus pci: add driver PCI_IDE pci: Matched Device 0000:00:06.0 with Driver PCI_IDE pci: Matched Device 0000:00:07.0 with Driver PCI_IDE pci: Matched Device 0000:00:08.0 with Driver PCI_IDE Probing IDE interface ide0... hda: SONY DVD RW DW-Q28A, ATAPI CD/DVD-ROM drive Probing IDE interface ide1... ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 bus ide: add device 0.0 bus ide: add driver ide-disk ide: Matched Device 0.0 with Driver ide-disk bus ide: add driver ide-cdrom ide: Matched Device 0.0 with Driver ide-cdrom hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 bound device '0.0' to driver 'ide-cdrom' ide: Bound Device 0.0 to Driver ide-cdrom bus ide: add driver ide-scsi libata version 1.20 loaded. bus pci: add driver sata_nv pci: Matched Device 0000:00:06.0 with Driver sata_nv pci: Matched Device 0000:00:07.0 with Driver sata_nv sata_nv 0000:00:07.0: version 0.8 ACPI: PCI Interrupt Link [LTID] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LTID] -> GSI 23 (level, high) -> IRQ 16 PCI: Setting latency timer of device 0000:00:07.0 to 64 ata1: SATA max UDMA/133 cmd 0x1C40 ctl 0x1C36 bmdma 0x1C10 irq 16 ata2: SATA max UDMA/133 cmd 0x1C38 ctl 0x1C32 bmdma 0x1C18 irq 16 ata1: no device found (phy stat 00000000) scsi0 : sata_nv ata2: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3d01 87:4003 88:203f ata2: dev 0 ATA-6, max UDMA/100, 586072368 sectors: LBA48 nv_sata: Primary device added nv_sata: Primary device removed nv_sata: Secondary device added nv_sata: Secondary device removed ata2: dev 0 configured for UDMA/100 scsi1 : sata_nv Vendor: ATA Model: WDC WD3000JD-00K Rev: 08.0 Type: Direct-Access ANSI SCSI revision: 05 bus scsi: add device 1:0:0:0 bound device '0000:00:07.0' to driver 'sata_nv' pci: Bound Device 0000:00:07.0 to Driver sata_nv pci: Matched Device 0000:00:08.0 with Driver sata_nv ACPI: PCI Interrupt Link [LSI1] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LSI1] -> GSI 22 (level, high) -> IRQ 17 PCI: Setting latency timer of device 0000:00:08.0 to 64 ata3: SATA max UDMA/133 cmd 0x1C58 ctl 0x1C4E bmdma 0x1C20 irq 17 ata4: SATA max UDMA/133 cmd 0x1C50 ctl 0x1C4A bmdma 0x1C28 irq 17 ata3: no device found (phy stat 00000000) scsi2 : sata_nv ata4: no device found (phy stat 00000000) scsi3 : sata_nv bound device '0000:00:08.0' to driver 'sata_nv' pci: Bound Device 0000:00:08.0 to Driver sata_nv bus scsi: add driver sd scsi: Matched Device 1:0:0:0 with Driver sd SCSI device sda: 586072368 512-byte hdwr sectors (300069 MB) SCSI device sda: drive cache: write back SCSI device sda: 586072368 512-byte hdwr sectors (300069 MB) SCSI device sda: drive cache: write back sda: sda1 sda2 sd 1:0:0:0: Attached scsi disk sda bound device '1:0:0:0' to driver 'sd' scsi: Bound Device 1:0:0:0 to Driver sd I2O subsystem v1.288 i2o: max drivers = 8 bus type 'i2o' registered bus i2o: add driver exec-osm bus pci: add driver PCI_I2O I2O Configuration OSM v1.248 bus i2o: add driver config-osm I2O Bus Adapter OSM v$Rev$ bus i2o: add driver bus-osm I2O Block Device OSM v1.287 bus i2o: add driver block-osm I2O SCSI Peripheral OSM v1.282 bus i2o: add driver scsi-osm I2O ProcFS OSM v1.145 bus i2o: add driver proc-osm Fusion MPT base driver 3.03.04 Copyright (c) 1999-2005 LSI Logic Corporation mptbase: Register for IOC reset notification Fusion MPT SPI Host driver 3.03.04 mptspi: Registered for IOC reset notifications bus pci: add driver mptspi Fusion MPT FC Host driver 3.03.04 mptfc: Registered for IOC reset notifications bus pci: add driver mptfc Fusion MPT SAS Host driver 3.03.04 mptsas: Registered for IOC reset notifications bus pci: add driver mptsas Fusion MPT misc device (ioctl) driver 3.03.04 mptctl: Registered with Fusion MPT base driver mptctl: /dev/mptctl @ (major,minor=10,220) mptctl: Registered for IOC reset notifications bus type 'ieee1394' registered bus pci: add driver ohci1394 pci: Matched Device 0000:01:05.0 with Driver ohci1394 ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org> ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 19 ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNK4] -> GSI 19 (level, high) -> IRQ 18 bus ieee1394: add device fw-host0 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[b0104000-b01047ff] Max Packet=[2048] bound device '0000:01:05.0' to driver 'ohci1394' pci: Bound Device 0000:01:05.0 to Driver ohci1394 ieee1394: raw1394: /dev/raw1394 device initialized bus ieee1394: add driver raw1394 usbmon: debugfs is not available bus pci: add driver ehci_hcd pci: Matched Device 0000:00:02.1 with Driver ehci_hcd ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS2] -> GSI 21 (level, high) -> IRQ 19 PCI: Setting latency timer of device 0000:00:02.1 to 64 ehci_hcd 0000:00:02.1: EHCI Host Controller ehci_hcd 0000:00:02.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:02.1 ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:02.1: irq 19, io mem 0xb0001000 ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 bus usb: add device usb1 bound device 'usb1' to driver 'usb' bus usb: add device 1-0:1.0 usb: Matched Device 1-0:1.0 with Driver hub hub 1-0:1.0: USB hub found hub 1-0:1.0: 10 ports detected bound device '1-0:1.0' to driver 'hub' usb: Bound Device 1-0:1.0 to Driver hub bound device '0000:00:02.1' to driver 'ehci_hcd' pci: Bound Device 0000:00:02.1 to Driver ehci_hcd USB Universal Host Controller Interface driver v2.3 bus pci: add driver uhci_hcd bus usb: add driver usblp usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... bus usb: add driver usb-storage usbcore: registered new driver usb-storage USB Mass Storage support registered. bus usb: add driver usbhid usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice bus serio: add driver atkbd serio: Matched Device serio0 with Driver atkbd NET: Registered protocol family 2 IP route cache hash table entries: 262144 (order: 8, 1048576 bytes) TCP established hash table entries: 262144 (order: 9, 3145728 bytes) TCP bind hash table entries: 65536 (order: 7, 786432 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered ip_conntrack version 2.4 (8192 buckets, 65536 max) - 212 bytes per conntrack serio: Matched Device serio1 with Driver atkbd input: AT Translated Set 2 keyboard as /class/input/input0 bound device 'serio1' to driver 'atkbd' serio: Bound Device serio1 to Driver atkbd bus serio: add driver psmouse serio: Matched Device serio0 with Driver psmouse ip_tables: (C) 2000-2002 Netfilter core team ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/ arp_tables: (C) 2002 David S. Miller TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Starting balanced_irq Using IPI Shortcut mode EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 224k freed kjournald starting. Commit interval 5 seconds bus ieee1394: add device 00e081000023a5ab ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e081000023a5ab] EXT3 FS on sda1, internal journal Linux agpgart interface v0.101 (c) Dave Jones bus type 'ac97' registered bus pci: add driver Intel ICH pci: Matched Device 0000:00:04.0 with Driver Intel ICH ACPI: PCI Interrupt Link [LACI] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LACI] -> GSI 20 (level, high) -> IRQ 20 PCI: Setting latency timer of device 0000:00:04.0 to 64 intel8x0_measure_ac97_clock: measured 54154 usecs intel8x0: clocking to 46977 bus ac97: add device card0-0 bound device '0000:00:04.0' to driver 'Intel ICH' pci: Bound Device 0000:00:04.0 to Driver Intel ICH bus type 'i2c' registered bus i2c: add driver i2c_adapter bus pci: add driver nForce2_smbus pci: Matched Device 0000:00:01.1 with Driver nForce2_smbus i2c_adapter i2c-0: nForce2 SMBus adapter at 0xa000 i2c_adapter i2c-1: nForce2 SMBus adapter at 0xa040 bound device '0000:00:01.1' to driver 'nForce2_smbus' pci: Bound Device 0000:00:01.1 to Driver nForce2_smbus floppy0: data CRC error: track 0, head 1, sector 7, size 2 floppy0: data CRC error: track 0, head 1, sector 7, size 2 end_request: I/O error, dev fd0, sector 24 Buffer I/O error on device fd0, logical block 3 floppy0: data CRC error: track 1, head 1, sector 8, size 2 floppy0: data CRC error: track 1, head 1, sector 8, size 2 end_request: I/O error, dev fd0, sector 61 Buffer I/O error on device fd0, logical block 7 floppy0: data CRC error: track 0, head 1, sector 7, size 2 floppy0: data CRC error: track 0, head 1, sector 7, size 2 end_request: I/O error, dev fd0, sector 24 Buffer I/O error on device fd0, logical block 3 floppy0: data CRC error: track 1, head 1, sector 8, size 2 floppy0: data CRC error: track 1, head 1, sector 8, size 2 end_request: I/O error, dev fd0, sector 61 Buffer I/O error on device fd0, logical block 7 floppy0: data CRC error: track 0, head 1, sector 7, size 2 floppy0: data CRC error: track 0, head 1, sector 7, size 2 end_request: I/O error, dev fd0, sector 24 FAT: Directory bread(block 24) failed floppy0: data CRC error: track 0, head 1, sector 7, size 2 floppy0: data CRC error: track 0, head 1, sector 7, size 2 end_request: I/O error, dev fd0, sector 24 FAT: Directory bread(block 24) failed floppy0: data CRC error: track 0, head 1, sector 7, size 2 floppy0: data CRC error: track 0, head 1, sector 7, size 2 end_request: I/O error, dev fd0, sector 24 FAT: Directory bread(block 24) failed floppy0: data CRC error: track 0, head 1, sector 7, size 2 floppy0: data CRC error: track 0, head 1, sector 7, size 2 end_request: I/O error, dev fd0, sector 24 FAT: Directory bread(block 24) failed floppy0: data CRC error: track 0, head 1, sector 7, size 2 floppy0: data CRC error: track 0, head 1, sector 7, size 2 end_request: I/O error, dev fd0, sector 24 FAT: Directory bread(block 24) failed floppy0: data CRC error: track 0, head 1, sector 7, size 2 floppy0: data CRC error: track 0, head 1, sector 7, size 2 end_request: I/O error, dev fd0, sector 24 FAT: Directory bread(block 24) failed floppy0: data CRC error: track 0, head 1, sector 7, size 2 floppy0: data CRC error: track 0, head 1, sector 7, size 2 end_request: I/O error, dev fd0, sector 24 FAT: Directory bread(block 24) failed floppy0: data CRC error: track 0, head 1, sector 7, size 2 floppy0: data CRC error: track 0, head 1, sector 7, size 2 end_request: I/O error, dev fd0, sector 24 FAT: Directory bread(block 24) failed
sorry for the formatting of the attachments. Also disregard the floppy I/O errors, they are because of a damaged floppy I tried to use to copy you the files. I hope this helps
The problem devices are here: 0a:06.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07) 0a:06.1 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07) behind this bridge: 08:0b.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode]) Bus: primary=08, secondary=0a, subordinate=0a, sec-latency=136 But we don't even see the devices: > ACPI: PCI Root Bridge [PCI2] (0000:08) > PCI: Probing PCI hardware (bus 08) > ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 > ACPI: PCI Root Bridge [PCI1] (0000:80) (note there are no "bus pci: add device ..." lines for this bridge.) Can you try a boot with "pci=nommconf"? I think MMCONFIG was added after 2.6.13, so maybe something's wrong with it on your box.
> I think MMCONFIG was added after 2.6.13, so maybe something's > wrong with it on your box. I take that back; MMCONFIG *was* in 2.6.13, but it was disabled for AMD CPUs because of some known issues. Maybe there's still one lingering. In any case, a boot with "pci=nommconf" would be very interesting.
You were right, indeed the pci=nommconf did the trick, the controller was detected. I had to enable the kernel debugging features and tweak the log buffer size because the log did not fit the dmesg, which I managed to now get complete. Linux version 2.6.15.4 (root@darkstar) (gcc version 3.3.6) #3 SMP PREEMPT Wed Feb 15 21:10:55 CET 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009ac00 (usable) BIOS-e820: 000000000009ac00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000da000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007ff90000 (usable) BIOS-e820: 000000007ff90000 - 000000007ff97000 (ACPI data) BIOS-e820: 000000007ff97000 - 0000000080000000 (ACPI NVS) BIOS-e820: 0000000080000000 - 00000000aff80000 (usable) BIOS-e820: 00000000aff80000 - 00000000b0000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec00400 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) BIOS-e820: 0000000100000000 - 0000000150000000 (usable) Warning only 4GB will be used. Use a PAE enabled kernel. 3200MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000f7950 On node 0 totalpages: 1048576 DMA zone: 4096 pages, LIFO batch:0 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 225280 pages, LIFO batch:31 HighMem zone: 819200 pages, LIFO batch:31 DMI present. ACPI: RSDP (v000 PTLTD ) @ 0x000f7920 ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x7ff926a5 ACPI: FADT (v001 NVIDIA CK8S 0x06040000 PTL_ 0x000f4240) @ 0x7ff96c90 ACPI: SRAT (v001 AMD HAMMER 0x06040000 AMD 0x00000001) @ 0x7ff96d04 ACPI: SPCR (v001 PTLTD $UCRTBL$ 0x06040000 PTL 0x00000001) @ 0x7ff96e14 ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x7ff96e64 ACPI: MCFG (v001 PTLTD MCFG 0x06040000 LTP 0x00000000) @ 0x7ff96f00 ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x7ff96f3c ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x7ff96fd8 ACPI: DSDT (v001 NVIDIA CK8 0x06040000 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x8008 ACPI: Local APIC address 0xfee00000 ACPI: 2 duplicate APIC table ignored. ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:1 APIC version 16 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 15:1 APIC version 16 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) Processor #2 15:1 APIC version 16 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled) Processor #3 15:1 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x05] address[0xd0000000] gsi_base[24]) IOAPIC[1]: apic_id 5, version 17, address 0xd0000000, GSI 24-27 ACPI: IOAPIC (id[0x06] address[0xd0001000] gsi_base[28]) IOAPIC[2]: apic_id 6, version 17, address 0xd0001000, GSI 28-31 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) ACPI: BIOS IRQ0 pin2 override ignored. ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 3 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at b4000000 (gap: b0000000:30000000) Built 1 zonelists Kernel command line: BOOT_IMAGE=2.6.15.4n ro root=801 pci=nommconf mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) mapped IOAPIC to ffffb000 (d0000000) mapped IOAPIC to ffffa000 (d0001000) Initializing CPU#0 PID hash table entries: 4096 (order: 12, 65536 bytes) Detected 2411.297 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x60 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 2838792k/4194304k available (3138k kernel code, 42616k reserved, 970k data, 224k init, 1965120k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 4827.49 BogoMIPS (lpj=9654980) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: After vendor identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 0(2) -> Core 0 CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000010 00000001 00000000 00000003 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. mtrr: v2.0 (20020519) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. CPU0: AMD Dual Core AMD Opteron(tm) Processor 280 stepping 02 Booting processor 1/1 eip 2000 Initializing CPU#1 Calibrating delay using timer specific routine.. 4822.61 BogoMIPS (lpj=9645223) CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: After vendor identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 1(2) -> Core 1 CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000010 00000001 00000000 00000003 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: AMD Dual Core AMD Opteron(tm) Processor 280 stepping 02 Booting processor 2/2 eip 2000 Initializing CPU#2 Calibrating delay using timer specific routine.. 4822.66 BogoMIPS (lpj=9645336) CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: After vendor identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 2(2) -> Core 1 CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000010 00000001 00000000 00000003 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#2. CPU2: AMD Dual Core AMD Opteron(tm) Processor 280 stepping 02 Booting processor 3/3 eip 2000 Initializing CPU#3 Calibrating delay using timer specific routine.. 4822.64 BogoMIPS (lpj=9645285) CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: After vendor identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 3(2) -> Core 1 CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000010 00000001 00000000 00000003 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#3. CPU3: AMD Dual Core AMD Opteron(tm) Processor 280 stepping 02 Total of 4 processors activated (19295.41 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 checking TSC synchronization across 4 CPUs: passed. Brought up 4 CPUs bus type 'platform' registered NET: Registered protocol family 16 bus type 'pci' registered ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd6b0, last bus=129 PCI: Using configuration type 1 ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI: Calling quirk c029fc90 for 0000:00:00.0 PCI: Calling quirk c038a030 for 0000:00:00.0 PCI: Calling quirk c038a3f0 for 0000:00:00.0 PCI: Calling quirk c029fc90 for 0000:00:01.0 PCI: Calling quirk c038a030 for 0000:00:01.0 PCI: Calling quirk c038a3f0 for 0000:00:01.0 PCI: Calling quirk c029fc90 for 0000:00:01.1 PCI: Calling quirk c038a030 for 0000:00:01.1 PCI: Calling quirk c038a3f0 for 0000:00:01.1 PCI: Calling quirk c029fc90 for 0000:00:02.0 PCI: Calling quirk c038a030 for 0000:00:02.0 PCI: Calling quirk c038a3f0 for 0000:00:02.0 PCI: Calling quirk c029fc90 for 0000:00:02.1 PCI: Calling quirk c038a030 for 0000:00:02.1 PCI: Calling quirk c038a3f0 for 0000:00:02.1 PCI: Calling quirk c029fc90 for 0000:00:04.0 PCI: Calling quirk c038a030 for 0000:00:04.0 PCI: Calling quirk c038a3f0 for 0000:00:04.0 PCI: Calling quirk c029fc90 for 0000:00:06.0 PCI: Calling quirk c038a030 for 0000:00:06.0 PCI: Calling quirk c038a3f0 for 0000:00:06.0 PCI: Calling quirk c029fc90 for 0000:00:07.0 PCI: Calling quirk c038a030 for 0000:00:07.0 PCI: Calling quirk c038a3f0 for 0000:00:07.0 PCI: Calling quirk c029fc90 for 0000:00:08.0 PCI: Calling quirk c038a030 for 0000:00:08.0 PCI: Calling quirk c038a3f0 for 0000:00:08.0 PCI: Calling quirk c029fc90 for 0000:00:09.0 PCI: Calling quirk c038a030 for 0000:00:09.0 PCI: Calling quirk c038a3f0 for 0000:00:09.0 PCI: Calling quirk c029fc90 for 0000:00:0a.0 PCI: Calling quirk c038a030 for 0000:00:0a.0 PCI: Calling quirk c038a3f0 for 0000:00:0a.0 PCI: Calling quirk c029fc90 for 0000:00:0e.0 PCI: Calling quirk c038a030 for 0000:00:0e.0 PCI: Calling quirk c038a3f0 for 0000:00:0e.0 PCI: Calling quirk c029fc90 for 0000:00:18.0 PCI: Calling quirk c038a030 for 0000:00:18.0 PCI: Calling quirk c038a3f0 for 0000:00:18.0 PCI: Calling quirk c029fc90 for 0000:00:18.1 PCI: Calling quirk c038a030 for 0000:00:18.1 PCI: Calling quirk c038a3f0 for 0000:00:18.1 PCI: Calling quirk c029fc90 for 0000:00:18.2 PCI: Calling quirk c038a030 for 0000:00:18.2 PCI: Calling quirk c038a3f0 for 0000:00:18.2 PCI: Calling quirk c029fc90 for 0000:00:18.3 PCI: Calling quirk c038a030 for 0000:00:18.3 PCI: Calling quirk c038a3f0 for 0000:00:18.3 PCI: Calling quirk c029fc90 for 0000:00:19.0 PCI: Calling quirk c038a030 for 0000:00:19.0 PCI: Calling quirk c038a3f0 for 0000:00:19.0 PCI: Calling quirk c029fc90 for 0000:00:19.1 PCI: Calling quirk c038a030 for 0000:00:19.1 PCI: Calling quirk c038a3f0 for 0000:00:19.1 PCI: Calling quirk c029fc90 for 0000:00:19.2 PCI: Calling quirk c038a030 for 0000:00:19.2 PCI: Calling quirk c038a3f0 for 0000:00:19.2 PCI: Calling quirk c029fc90 for 0000:00:19.3 PCI: Calling quirk c038a030 for 0000:00:19.3 PCI: Calling quirk c038a3f0 for 0000:00:19.3 PCI: Calling quirk c029fc90 for 0000:01:05.0 PCI: Calling quirk c038a030 for 0000:01:05.0 PCI: Calling quirk c038a3f0 for 0000:01:05.0 PCI: Transparent bridge - 0000:00:09.0 PCI: Calling quirk c029fc90 for 0000:02:00.0 PCI: Calling quirk c038a030 for 0000:02:00.0 PCI: Calling quirk c038a3f0 for 0000:02:00.0 Boot video device is 0000:02:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] bus pci: add device 0000:00:00.0 bus pci: add device 0000:00:01.0 bus pci: add device 0000:00:01.1 bus pci: add device 0000:00:02.0 bus pci: add device 0000:00:02.1 bus pci: add device 0000:00:04.0 bus pci: add device 0000:00:06.0 bus pci: add device 0000:00:07.0 bus pci: add device 0000:00:08.0 bus pci: add device 0000:00:09.0 bus pci: add device 0000:00:0a.0 bus pci: add device 0000:00:0e.0 bus pci: add device 0000:00:18.0 bus pci: add device 0000:00:18.1 bus pci: add device 0000:00:18.2 bus pci: add device 0000:00:18.3 bus pci: add device 0000:00:19.0 bus pci: add device 0000:00:19.1 bus pci: add device 0000:00:19.2 bus pci: add device 0000:00:19.3 bus pci: add device 0000:01:05.0 bus pci: add device 0000:02:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LNK3] (IRQs 16 17 18 19) *0 ACPI: PCI Interrupt Link [LNK4] (IRQs 16 17 18 19) *0 ACPI: PCI Interrupt Link [LNK5] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22 23) *0 ACPI: PCI Interrupt Link [LSI1] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Root Bridge [PCI2] (0000:08) PCI: Probing PCI hardware (bus 08) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI: Calling quirk c029fc90 for 0000:08:0a.0 PCI: Calling quirk c038a030 for 0000:08:0a.0 PCI: Calling quirk c038a3f0 for 0000:08:0a.0 PCI: Calling quirk c029fc90 for 0000:08:0a.1 PCI: Calling quirk c038a030 for 0000:08:0a.1 PCI: Calling quirk c038a3f0 for 0000:08:0a.1 PCI: Calling quirk c029fc90 for 0000:08:0b.0 PCI: Calling quirk c038a030 for 0000:08:0b.0 PCI: Calling quirk c038a3f0 for 0000:08:0b.0 PCI: Calling quirk c029fc90 for 0000:08:0b.1 PCI: Calling quirk c038a030 for 0000:08:0b.1 PCI: Calling quirk c038a3f0 for 0000:08:0b.1 PCI: Calling quirk c029fc90 for 0000:0a:06.0 PCI: Calling quirk c038a030 for 0000:0a:06.0 PCI: Calling quirk c038a3f0 for 0000:0a:06.0 PCI: Calling quirk c029fc90 for 0000:0a:06.1 PCI: Calling quirk c038a030 for 0000:0a:06.1 PCI: Calling quirk c038a3f0 for 0000:0a:06.1 bus pci: add device 0000:08:0a.0 bus pci: add device 0000:08:0a.1 bus pci: add device 0000:08:0b.0 bus pci: add device 0000:08:0b.1 bus pci: add device 0000:0a:06.0 bus pci: add device 0000:0a:06.1 ACPI: PCI Interrupt Routing Table [\_SB_.PCI2.G0PA._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI2.G0PB._PRT] ACPI: PCI Root Bridge [PCI1] (0000:80) PCI: Probing PCI hardware (bus 80) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI: Calling quirk c029fc90 for 0000:80:00.0 PCI: Calling quirk c038a030 for 0000:80:00.0 PCI: Calling quirk c038a3f0 for 0000:80:00.0 PCI: Calling quirk c029fc90 for 0000:80:01.0 PCI: Calling quirk c038a030 for 0000:80:01.0 PCI: Calling quirk c038a3f0 for 0000:80:01.0 PCI: Calling quirk c029fc90 for 0000:80:0a.0 PCI: Calling quirk c038a030 for 0000:80:0a.0 PCI: Calling quirk c038a3f0 for 0000:80:0a.0 PCI: Calling quirk c029fc90 for 0000:80:0e.0 PCI: Calling quirk c038a030 for 0000:80:0e.0 PCI: Calling quirk c038a3f0 for 0000:80:0e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT] bus pci: add device 0000:80:00.0 bus pci: add device 0000:80:01.0 bus pci: add device 0000:80:0a.0 bus pci: add device 0000:80:0e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.XVR0._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay bus type 'pnp' registered bus type 'scsi' registered SCSI subsystem initialized bus type 'usb' registered bus usb: add driver usbfs usbcore: registered new driver usbfs bus usb: add driver hub usbcore: registered new driver hub bus usb: add driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report bus pnp: add driver system PCI: Bridge: 0000:00:09.0 IO window: disabled. MEM window: b0100000-b01fffff PREFETCH window: disabled. PCI: Failed to allocate mem resource #6:20000@d0000000 for 0000:02:00.0 PCI: Bridge: 0000:00:0e.0 IO window: disabled. MEM window: b1000000-b2ffffff PREFETCH window: c0000000-cfffffff PCI: Setting latency timer of device 0000:00:09.0 to 64 PCI: Setting latency timer of device 0000:00:0e.0 to 64 PCI: Bridge: 0000:08:0a.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:08:0b.0 IO window: 2000-2fff MEM window: d0100000-d04fffff PREFETCH window: b4000000-b41fffff PCI: Bridge: 0000:80:0e.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Setting latency timer of device 0000:80:0e.0 to 64 Simple Boot Flag at 0x36 set to 0x1 Machine check exception polling timer started. apm: BIOS not found. highmem bounce pool size: 64 pages Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NTFS driver 2.1.25 [Flags: R/W]. JFS: nTxBlock = 8192, nTxLock = 65536 Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered PCI: Calling quirk c029fb50 for 0000:00:00.0 PCI: Calling quirk c036b450 for 0000:00:00.0 PCI: Calling quirk c029fb50 for 0000:80:00.0 PCI: Calling quirk c036b450 for 0000:80:00.0 PCI: Calling quirk c029fb50 for 0000:00:01.0 PCI: Calling quirk c036b450 for 0000:00:01.0 PCI: Calling quirk c029fb50 for 0000:00:01.1 PCI: Calling quirk c036b450 for 0000:00:01.1 PCI: Calling quirk c029fb50 for 0000:00:02.0 PCI: Calling quirk c036b450 for 0000:00:02.0 PCI: Calling quirk c029fb50 for 0000:00:02.1 PCI: Calling quirk c036b450 for 0000:00:02.1 PCI: Calling quirk c029fb50 for 0000:00:04.0 PCI: Calling quirk c036b450 for 0000:00:04.0 PCI: Calling quirk c029fb50 for 0000:00:06.0 PCI: Calling quirk c036b450 for 0000:00:06.0 PCI: Calling quirk c029fb50 for 0000:00:07.0 PCI: Calling quirk c036b450 for 0000:00:07.0 PCI: Calling quirk c029fb50 for 0000:00:08.0 PCI: Calling quirk c036b450 for 0000:00:08.0 PCI: Calling quirk c029fb50 for 0000:00:09.0 PCI: Calling quirk c036b450 for 0000:00:09.0 PCI: Calling quirk c029fb50 for 0000:00:0a.0 PCI: Calling quirk c036b450 for 0000:00:0a.0 PCI: Calling quirk c029fb50 for 0000:80:0a.0 PCI: Calling quirk c036b450 for 0000:80:0a.0 PCI: Calling quirk c029fb50 for 0000:00:0e.0 PCI: Calling quirk c036b450 for 0000:00:0e.0 PCI: Calling quirk c029fb50 for 0000:80:0e.0 PCI: Calling quirk c036b450 for 0000:80:0e.0 PCI: Calling quirk c029fb50 for 0000:00:18.0 PCI: Calling quirk c036b450 for 0000:00:18.0 PCI: Calling quirk c029fb50 for 0000:00:19.0 PCI: Calling quirk c036b450 for 0000:00:19.0 PCI: Calling quirk c029fb50 for 0000:00:18.1 PCI: Calling quirk c036b450 for 0000:00:18.1 PCI: Calling quirk c029fb50 for 0000:00:19.1 PCI: Calling quirk c036b450 for 0000:00:19.1 PCI: Calling quirk c029fb50 for 0000:00:18.2 PCI: Calling quirk c036b450 for 0000:00:18.2 PCI: Calling quirk c029fb50 for 0000:00:19.2 PCI: Calling quirk c036b450 for 0000:00:19.2 PCI: Calling quirk c029fb50 for 0000:00:18.3 PCI: Calling quirk c036b450 for 0000:00:18.3 PCI: Calling quirk c029fb50 for 0000:00:19.3 PCI: Calling quirk c036b450 for 0000:00:19.3 PCI: Calling quirk c029fb50 for 0000:01:05.0 PCI: Calling quirk c036b450 for 0000:01:05.0 PCI: Calling quirk c029fb50 for 0000:02:00.0 PCI: Calling quirk c036b450 for 0000:02:00.0 PCI: Calling quirk c051ae60 for 0000:08:0a.0 PCI: MSI quirk detected. pci_msi_quirk set. PCI: Calling quirk c029fb50 for 0000:08:0a.0 PCI: Calling quirk c036b450 for 0000:08:0a.0 PCI: Calling quirk c051ae60 for 0000:08:0b.0 PCI: MSI quirk detected. pci_msi_quirk set. PCI: Calling quirk c029fb50 for 0000:08:0b.0 PCI: Calling quirk c036b450 for 0000:08:0b.0 PCI: Calling quirk c029fb50 for 0000:08:0a.1 PCI: Calling quirk c036b450 for 0000:08:0a.1 PCI: Calling quirk c029fb50 for 0000:08:0b.1 PCI: Calling quirk c036b450 for 0000:08:0b.1 PCI: Calling quirk c029fb50 for 0000:0a:06.0 PCI: Calling quirk c036b450 for 0000:0a:06.0 PCI: Calling quirk c029fb50 for 0000:0a:06.1 PCI: Calling quirk c036b450 for 0000:0a:06.1 PCI: Calling quirk c029fb50 for 0000:80:01.0 PCI: Calling quirk c036b450 for 0000:80:01.0 bus type 'pci_express' registered bus pci: add driver pcieport-driver pci: Matched Device 0000:00:0e.0 with Driver pcieport-driver PCI: Setting latency timer of device 0000:00:0e.0 to 64 pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[pcie00] bus pci_express: add device pcie00 bound device '0000:00:0e.0' to driver 'pcieport-driver' pci: Bound Device 0000:00:0e.0 to Driver pcieport-driver pci: Matched Device 0000:08:0a.0 with Driver pcieport-driver pci: Matched Device 0000:08:0b.0 with Driver pcieport-driver pci: Matched Device 0000:80:0e.0 with Driver pcieport-driver PCI: Setting latency timer of device 0000:80:0e.0 to 64 pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[pcie00] bus pci_express: add device pcie00 bound device '0000:80:0e.0' to driver 'pcieport-driver' pci: Bound Device 0000:80:0e.0 to Driver pcieport-driver bus type 'serio' registered bus pnp: add driver i8042 kbd bus pnp: add driver i8042 aux bus pnp: remove driver i8042 kbd bus pnp: remove driver i8042 aux PNP: No PS/2 controller found. Probing ports directly. bus platform: add driver i8042 bus platform: add device i8042 platform: Matched Device i8042 with Driver i8042 bound device 'i8042' to driver 'i8042' platform: Bound Device i8042 to Driver i8042 serio: i8042 AUX port at 0x60,0x64 irq 12 bus serio: add device serio0 serio: i8042 KBD port at 0x60,0x64 irq 1 bus serio: add device serio1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled bus platform: add device serial8250 serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A bus platform: add driver serial8250 platform: Matched Device serial8250 with Driver serial8250 bound device 'serial8250' to driver 'serial8250' platform: Bound Device serial8250 to Driver serial8250 bus pnp: add driver serial bus pci: add driver serial Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 bus platform: add device floppy.0 loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx bus type 'ide' registered bus pci: add driver RZ1000_IDE bus pci: add driver PCI_IDE pci: Matched Device 0000:00:06.0 with Driver PCI_IDE pci: Matched Device 0000:00:07.0 with Driver PCI_IDE pci: Matched Device 0000:00:08.0 with Driver PCI_IDE Probing IDE interface ide0... hda: SONY DVD RW DW-Q28A, ATAPI CD/DVD-ROM drive Probing IDE interface ide1... ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 bus ide: add device 0.0 bus ide: add driver ide-disk ide: Matched Device 0.0 with Driver ide-disk bus ide: add driver ide-cdrom ide: Matched Device 0.0 with Driver ide-cdrom hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 bound device '0.0' to driver 'ide-cdrom' ide: Bound Device 0.0 to Driver ide-cdrom bus ide: add driver ide-scsi libata version 1.20 loaded. bus pci: add driver sata_nv pci: Matched Device 0000:00:06.0 with Driver sata_nv pci: Matched Device 0000:00:07.0 with Driver sata_nv sata_nv 0000:00:07.0: version 0.8 ACPI: PCI Interrupt Link [LTID] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LTID] -> GSI 23 (level, high) -> IRQ 16 PCI: Setting latency timer of device 0000:00:07.0 to 64 ata1: SATA max UDMA/133 cmd 0x1C40 ctl 0x1C36 bmdma 0x1C10 irq 16 ata2: SATA max UDMA/133 cmd 0x1C38 ctl 0x1C32 bmdma 0x1C18 irq 16 ata1: no device found (phy stat 00000000) scsi0 : sata_nv ata2: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3469 86:3d01 87:4003 88:203f ata2: dev 0 ATA-6, max UDMA/100, 586072368 sectors: LBA48 nv_sata: Primary device added nv_sata: Primary device removed nv_sata: Secondary device added nv_sata: Secondary device removed ata2: dev 0 configured for UDMA/100 scsi1 : sata_nv Vendor: ATA Model: WDC WD3000JD-00K Rev: 08.0 Type: Direct-Access ANSI SCSI revision: 05 bus scsi: add device 1:0:0:0 bound device '0000:00:07.0' to driver 'sata_nv' pci: Bound Device 0000:00:07.0 to Driver sata_nv pci: Matched Device 0000:00:08.0 with Driver sata_nv ACPI: PCI Interrupt Link [LSI1] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LSI1] -> GSI 22 (level, high) -> IRQ 17 PCI: Setting latency timer of device 0000:00:08.0 to 64 ata3: SATA max UDMA/133 cmd 0x1C58 ctl 0x1C4E bmdma 0x1C20 irq 17 ata4: SATA max UDMA/133 cmd 0x1C50 ctl 0x1C4A bmdma 0x1C28 irq 17 ata3: no device found (phy stat 00000000) scsi2 : sata_nv ata4: no device found (phy stat 00000000) scsi3 : sata_nv bound device '0000:00:08.0' to driver 'sata_nv' pci: Bound Device 0000:00:08.0 to Driver sata_nv bus scsi: add driver sd scsi: Matched Device 1:0:0:0 with Driver sd SCSI device sda: 586072368 512-byte hdwr sectors (300069 MB) SCSI device sda: drive cache: write back SCSI device sda: 586072368 512-byte hdwr sectors (300069 MB) SCSI device sda: drive cache: write back sda: sda1 sda2 sd 1:0:0:0: Attached scsi disk sda bound device '1:0:0:0' to driver 'sd' scsi: Bound Device 1:0:0:0 to Driver sd I2O subsystem v1.288 i2o: max drivers = 8 bus type 'i2o' registered bus i2o: add driver exec-osm bus pci: add driver PCI_I2O I2O Configuration OSM v1.248 bus i2o: add driver config-osm I2O Bus Adapter OSM v$Rev$ bus i2o: add driver bus-osm I2O Block Device OSM v1.287 bus i2o: add driver block-osm I2O SCSI Peripheral OSM v1.282 bus i2o: add driver scsi-osm I2O ProcFS OSM v1.145 bus i2o: add driver proc-osm Fusion MPT base driver 3.03.04 Copyright (c) 1999-2005 LSI Logic Corporation mptbase: Register for IOC reset notification Fusion MPT SPI Host driver 3.03.04 mptspi: Registered for IOC reset notifications bus pci: add driver mptspi pci: Matched Device 0000:0a:06.0 with Driver mptspi ACPI: PCI Interrupt 0000:0a:06.0[A] -> GSI 30 (level, low) -> IRQ 18 mptbase: mpt_adapter_install mptbase: 64 BIT PCI BUS DMA ADDRESSING SUPPORTED mptbase: Using 64 bit consistent mask mptbase: MPT adapter @ d0200000, msize=1048576d bytes mptbase: (port i/o @ 2000, psize=256d bytes) mptbase: mem = f8cd8000, mem_phys = d0200000 mptbase: facts @ f7dd7a6c, pfacts[0] @ f7dd7abc mptbase: ioc0 installed at interrupt 18 mptbase: ioc0: PCI device 0000:0a:06.0 devfn=a/30, searching for devfn match on ffffffff or 1 mptbase: Initiating ioc0 bringup mptbase: ioc0: IOC operational unexpected mptbase: whoinit 0x2 statefault 0 force 0 mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: Sending get IocFacts request req_sz=12 reply_sz=80 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell ACK (count=0) mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: WaitForDoorbell ACK (count=1) 03000000 00000000 00000000 mptbase: ioc0: WaitForDoorbell INT (cnt=0) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 030f0102 00000e00 00000000 00000000 00000000 00080030 001800ff 02020000 00000000 000100ff 00000000 01100080 00009f30 013601ce 01032700 mptbase: ioc0: NB_for_64_byte_frame=2 NBShiftFactor=5 BlockSize=8 mptbase: ioc0: reply_sz= 64, reply_depth= 128 mptbase: ioc0: req_sz = 96, req_depth = 255 mptbase: ioc0: Sending get PortFacts(0) request mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell ACK (count=0) mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: WaitForDoorbell ACK (count=1) 05000000 00000000 00000000 mptbase: ioc0: WaitForDoorbell INT (cnt=0) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 050a0000 00000000 00000000 00000000 00000000 00100100 000c0007 00000020 00000000 00000000 ioc0: 53C1030: Capabilities={Initiator,Target} mptbase: ioc0 ReqToChain alloc @ f7dd4800, sz=1020 bytes mptbase: ioc0 RequestNB alloc @ f7de9c00, sz=1020 bytes mptbase: ioc0 num_sge=17 numSGE=534 mptbase: ioc0 Now numSGE=128 num_sge=138 num_chain=13 mptbase: ioc0 ChainToChain alloc @ f7e56000, sz=6604 bytes mptbase: ioc0.ReplyBuffer sz=64 bytes, ReplyDepth=128 mptbase: ioc0.ReplyBuffer sz=8192[2000] bytes mptbase: ioc0.RequestBuffer sz=96 bytes, RequestDepth=255 mptbase: ioc0.RequestBuffer sz=24480[5fa0] bytes mptbase: ioc0.ChainBuffer sz=96 bytes, ChainDepth=1651 mptbase: ioc0.ChainBuffer sz=158496[26b20] bytes num_chain=1651 mptbase: ioc0.Total alloc @ f7e80000[37e80000], sz=191168[2eac0] bytes mptbase: ioc0 ReplyBuffers @ f7e80000[37e80000] mptbase: ioc0 RequestBuffers @ f7e82000[37e82000] mptbase :ioc0 ChainBuffers @ f7e87fa0(37e87fa0) mptbase: ioc0.SenseBuffers @ f7e58000[37e58000] mptbase: ioc0.ReplyBuffers @ f7e80000[37e80000] mptbase: ioc0: upload_fw 0 facts.Flags=0 mptbase: ioc0: facts.MsgVersion=102 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell ACK (count=0) mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: WaitForDoorbell ACK (count=1) 02000004 00011000 00000000 mptbase: ioc0: WaitForDoorbell INT (cnt=0) howlong=10 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 02050004 00011000 00000000 00000000 00000000 mptbase: ioc0: Sending Port(0)Enable (req @ c355fd60) mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell ACK (count=0) mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: WaitForDoorbell ACK (count=1) mptbase: ioc0: WaitForDoorbell ACK (count=1) 06000000 00000000 00000000 mptbase: ioc0: WaitForDoorbell INT (cnt=0) howlong=30 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc0: WaitForDoorbell INT (cnt=1) howlong=5 06050000 00000000 00000000 00000000 00000000 mptbase: ioc0: INFO - Wait IOC_OPERATIONAL state (cnt=0) mptbase: ioc0: SCSI device NVRAM settings @ f7dd3ec0, sz=64 07080001 80000000 000f0000 00000000 00000000 0000000a 00000000 00000001 mptbase: Event data: 00000001 mptbase: ioc0: Sending Config request type 3, page 0 and action 0 04060000 00000000 000f0001 00000000 00000000 03000302 mptbase: ioc0: config_complete (mf=f7e82060,mr=f7e80040) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc0: Sending Config request type 3, page 0 and action 1 04060001 00000000 000f0002 00000000 00000000 03000302 mptbase: ioc0: config_complete (mf=f7e820c0,mr=f7e80080) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc0: Sending Config request type 3, page 2 and action 0 04060000 00000000 000f0003 00000000 00000000 23021302 mptbase: ioc0: config_complete (mf=f7e82120,mr=f7e800c0) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc0: Sending Config request type 3, page 2 and action 6 04060006 00000000 000f0004 00000000 00000000 03021302 mptbase: ioc0: config_complete (mf=f7e82180,mr=f7e80100) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc0: Sending Config request type 4, page 1 and action 0 04060000 00000000 000f0005 00000000 00000000 14010405 mptbase: ioc0: config_complete (mf=f7e821e0,mr=f7e80140) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc0: Sending Config request type 4, page 0 and action 0 04060000 00000000 000f0006 00000000 00000000 04000304 mptbase: ioc0: config_complete (mf=f7e82240,mr=f7e80180) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc0: Headers: 0: version 4 length 3 mptbase: ioc0: Headers: 1: version 5 length 4 mptbase: ioc0: Sending Config request type 1, page 2 and action 0 04060000 00000000 000f0007 00000000 00000000 01020502 mptbase: ioc0: config_complete (mf=f7e822a0,mr=f7e801c0) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc0: Sending Config request type 1, page 2 and action 1 04060001 00000000 000f0008 00000000 00000000 01020502 mptbase: ioc0: config_complete (mf=f7e82300,mr=f7e80200) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc0: Sending Config request type 1, page 1 and action 0 04060000 00000000 000f0009 00000000 00000000 21010401 mptbase: ioc0: config_complete (mf=f7e82360,mr=f7e80240) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc0: Sending Config request type 1, page 1 and action 1 04060001 00000000 000f000a 00000000 00000000 01010401 mptbase: ioc0: config_complete (mf=f7e823c0,mr=f7e80280) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc0: Coalescing Enabled Timeout = 16 mptbase: ioc0: Sending Config request type 1, page 4 and action 0 04060000 00000000 000f000b 00000000 00000000 11040300 mptbase: ioc0: config_complete (mf=f7e82420,mr=f7e802c0) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc0: Sending Config request type 1, page 4 and action 1 04060001 00000000 000f000c 00000000 00000000 01040300 mptbase: ioc0: config_complete (mf=f7e82480,mr=f7e80300) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc0: Sending Config request type 0, page 2 and action 0 04060000 00000000 000f000d 00000000 00000000 20020700 mptbase: ioc0: config_complete (mf=f7e824e0,mr=f7e80340) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc0: Sending Config request type 0, page 2 and action 1 04060001 00000000 000f000e 00000000 00000000 00020700 mptbase: ioc0: config_complete (mf=f7e82540,mr=f7e80380) IOCStatus=0000h, IOCLogInfo=00000000h mptspi: ioc0: ScsiLookup @ f7de9800, sz=1020 Targets @ f7dd3e80, sz=64 scsi4 : ioc0: LSI53C1030, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=18 Vendor: SEAGATE Model: ST373454LW Rev: 0003 Type: Direct-Access ANSI SCSI revision: 03 mptscsih: ioc0: device @ f7de9400, id=0, LUN=0, channel=0 mptscsih: ioc0: sdtr 1 wdtr 1 ppr 1 inq length=144 mptscsih: ioc0: initTarget bus=0 id=0 lun=0 hd=f7dd72cc mptscsih: ioc0: write SDP1: id 0 pgaddr 0x0 req 0xff00 config 0x0 mptscsih: ioc0: Queue depth=64, tflags=1b mptscsih: ioc0: negoFlags=0, maxOffset=7f, SyncFactor=8 04060002 00000000 000e0011 00000000 00000000 04010405 mptscsih: ioc0: tagged 1, simple 1, ordered 0 bus scsi: add device 4:0:0:0 scsi: Matched Device 4:0:0:0 with Driver sd SCSI device sdb: 143374744 512-byte hdwr sectors (73408 MB) SCSI device sdb: drive cache: write back SCSI device sdb: 143374744 512-byte hdwr sectors (73408 MB) SCSI device sdb: drive cache: write back sdb: sdb1 sdb3 sdb4 sd 4:0:0:0: Attached scsi disk sdb bound device '4:0:0:0' to driver 'sd' scsi: Bound Device 4:0:0:0 to Driver sd 00080000 0001400c 000e001b 00450000 00000000 00000010 00000000 00000000 00080001 00014006 000e001c 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 1 lun 0 max 255 00080002 00014006 000e001d 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 2 lun 0 max 255 mptbase: ioc0: Sending Config request type 4, page 1 and action 2 04060002 00000000 000f001f 00000000 00000000 04010405 mptbase: ioc0: config_complete (mf=f7e82ba0,mr=f7e804c0) IOCStatus=0000h, IOCLogInfo=00000000h 00080003 00014006 000e001e 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 3 lun 0 max 255 00080004 00014006 000e0021 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 4 lun 0 max 255 00080005 00024006 000e0023 00430000 00000000 00000000 00000000 00000000 mptbase: ioc0: Sending Config request type 4, page 1 and action 2 mptscsih: search_running target 5 lun 0 max 255 04060002 00000000 000f0024 00000000 00000000 04010405 mptbase: ioc0: config_complete (mf=f7e82d80,mr=f7e805c0) IOCStatus=0000h, IOCLogInfo=00000000h 00080006 00014006 000e0025 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 6 lun 0 max 255 00080008 00014006 000e0027 00430000 00000000 00000000 00000000 00000000 mptbase: ioc0: Sending Config request type 4, page 0 and action 1 mptscsih: search_running target 8 lun 0 max 255 04060001 00000000 000f0028 00000000 00000000 04000304 mptbase: ioc0: config_complete (mf=f7e82f00,mr=f7e80680) IOCStatus=0000h, IOCLogInfo=00000000h mptscsih: ioc0: initTarget bus=0 id=0 lun=0 hd=f7dd72cc 00080009 00014006 000e0029 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 9 lun 0 max 255 0008000a 00024006 000e002c 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 10 lun 0 max 255 0008000b 00024006 000e002e 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 11 lun 0 max 255 0008000c 00024006 000e0030 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 12 lun 0 max 255 0008000d 00024006 000e0032 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 13 lun 0 max 255 0008000e 00024006 000e0034 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 14 lun 0 max 255 0008000f 00024006 000e0036 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 15 lun 0 max 255 bound device '0000:0a:06.0' to driver 'mptspi' pci: Bound Device 0000:0a:06.0 to Driver mptspi pci: Matched Device 0000:0a:06.1 with Driver mptspi ACPI: PCI Interrupt 0000:0a:06.1[B] -> GSI 31 (level, low) -> IRQ 19 mptbase: mpt_adapter_install mptbase: 64 BIT PCI BUS DMA ADDRESSING SUPPORTED mptbase: Using 64 bit consistent mask mptbase: MPT adapter @ d0400000, msize=1048576d bytes mptbase: (port i/o @ 2400, psize=256d bytes) mptbase: mem = f8cda000, mem_phys = d0400000 mptbase: facts @ f7e0ea6c, pfacts[0] @ f7e0eabc mptbase: ioc1 installed at interrupt 19 mptbase: ioc1: PCI device 0000:0a:06.1 devfn=a/31, searching for devfn match on 0 or 2 mptbase: FOUND! binding ioc1 <==> ioc0 mptbase: Initiating ioc1 bringup mptbase: ioc1: IOC operational unexpected mptbase: whoinit 0x2 statefault 0 force 0 mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: Sending get IocFacts request req_sz=12 reply_sz=80 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell ACK (count=0) mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: WaitForDoorbell ACK (count=1) 03000000 00000000 00000000 mptbase: ioc1: WaitForDoorbell INT (cnt=0) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 030f0102 00010e00 00000000 00000000 00000000 00080030 001800ff 02020000 00000000 000100ff 00000000 01100080 00009f30 e6000010 01032700 mptbase: ioc1: NB_for_64_byte_frame=2 NBShiftFactor=5 BlockSize=8 mptbase: ioc1: reply_sz= 64, reply_depth= 128 mptbase: ioc1: req_sz = 96, req_depth = 255 mptbase: ioc1: Sending get PortFacts(0) request mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell ACK (count=0) mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: WaitForDoorbell ACK (count=1) 05000000 00000000 00000000 mptbase: ioc1: WaitForDoorbell INT (cnt=0) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 050a0000 00000000 00000000 00000000 00000000 00100100 000c0007 00000020 00000000 00000000 ioc1: 53C1030: Capabilities={Initiator,Target} mptbase: ioc1 ReqToChain alloc @ f7de9000, sz=1020 bytes mptbase: ioc1 RequestNB alloc @ f7cb8000, sz=1020 bytes mptbase: ioc1 num_sge=17 numSGE=534 mptbase: ioc1 Now numSGE=128 num_sge=138 num_chain=13 mptbase: ioc1 ChainToChain alloc @ f7e5e000, sz=6604 bytes mptbase: ioc1.ReplyBuffer sz=64 bytes, ReplyDepth=128 mptbase: ioc1.ReplyBuffer sz=8192[2000] bytes mptbase: ioc1.RequestBuffer sz=96 bytes, RequestDepth=255 mptbase: ioc1.RequestBuffer sz=24480[5fa0] bytes mptbase: ioc1.ChainBuffer sz=96 bytes, ChainDepth=1651 mptbase: ioc1.ChainBuffer sz=158496[26b20] bytes num_chain=1651 mptbase: ioc1.Total alloc @ f7ec0000[37ec0000], sz=191168[2eac0] bytes mptbase: ioc1 ReplyBuffers @ f7ec0000[37ec0000] mptbase: ioc1 RequestBuffers @ f7ec2000[37ec2000] mptbase :ioc1 ChainBuffers @ f7ec7fa0(37ec7fa0) mptbase: ioc1.SenseBuffers @ f7e60000[37e60000] mptbase: ioc1.ReplyBuffers @ f7ec0000[37ec0000] mptbase: ioc1: upload_fw 0 facts.Flags=0 mptbase: ioc1: facts.MsgVersion=102 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell ACK (count=0) mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: WaitForDoorbell ACK (count=1) 02000004 00011000 00000000 mptbase: ioc1: WaitForDoorbell INT (cnt=0) howlong=10 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 02050004 00011000 00000000 00000000 00000000 mptbase: ioc1: Sending Port(0)Enable (req @ c355fd60) mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell ACK (count=0) mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: WaitForDoorbell ACK (count=1) mptbase: ioc1: WaitForDoorbell ACK (count=1) 06000000 00000000 00000000 mptbase: ioc1: WaitForDoorbell INT (cnt=0) howlong=30 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 mptbase: ioc1: WaitForDoorbell INT (cnt=1) howlong=5 06050000 00000000 00000000 00000000 00000000 mptbase: ioc1: INFO - Wait IOC_OPERATIONAL state (cnt=0) mptbase: alt-ioc0 reply irq re-enabled mptbase: ioc1: SCSI device NVRAM settings @ c37bf200, sz=64 07080001 80000000 000f0000 00000000 00000000 0000000a 00000000 00000001 mptbase: Event data: 00000001 mptbase: ioc1: Sending Config request type 3, page 0 and action 0 04060000 00000000 000f0001 00000000 00000000 03000302 mptbase: ioc1: config_complete (mf=f7ec2060,mr=f7ec0040) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc1: Sending Config request type 3, page 0 and action 1 04060001 00000000 000f0002 00000000 00000000 03000302 mptbase: ioc1: config_complete (mf=f7ec20c0,mr=f7ec0080) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc1: Sending Config request type 3, page 2 and action 0 04060000 00000000 000f0003 00000000 00000000 23021302 mptbase: ioc1: config_complete (mf=f7ec2120,mr=f7ec00c0) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc1: Sending Config request type 3, page 2 and action 6 04060006 00000000 000f0004 00000000 00000000 03021302 mptbase: ioc1: config_complete (mf=f7ec2180,mr=f7ec0100) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc1: Sending Config request type 4, page 1 and action 0 04060000 00000000 000f0005 00000000 00000000 14010405 mptbase: ioc1: config_complete (mf=f7ec21e0,mr=f7ec0140) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc1: Sending Config request type 4, page 0 and action 0 04060000 00000000 000f0006 00000000 00000000 04000304 mptbase: ioc1: config_complete (mf=f7ec2240,mr=f7ec0180) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc1: Headers: 0: version 4 length 3 mptbase: ioc1: Headers: 1: version 5 length 4 mptbase: ioc1: Sending Config request type 1, page 2 and action 0 04060000 00000000 000f0007 00000000 00000000 01020502 mptbase: ioc1: config_complete (mf=f7ec22a0,mr=f7ec01c0) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc1: Sending Config request type 1, page 2 and action 1 04060001 00000000 000f0008 00000000 00000000 01020502 mptbase: ioc1: config_complete (mf=f7ec2300,mr=f7ec0200) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc1: Sending Config request type 1, page 1 and action 0 04060000 00000000 000f0009 00000000 00000000 21010401 mptbase: ioc1: config_complete (mf=f7ec2360,mr=f7ec0240) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc1: Sending Config request type 1, page 1 and action 1 04060001 00000000 000f000a 00000000 00000000 01010401 mptbase: ioc1: config_complete (mf=f7ec23c0,mr=f7ec0280) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc1: Coalescing Enabled Timeout = 16 mptbase: ioc1: Sending Config request type 1, page 4 and action 0 04060000 00000000 000f000b 00000000 00000000 11040300 mptbase: ioc1: config_complete (mf=f7ec2420,mr=f7ec02c0) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc1: Sending Config request type 1, page 4 and action 1 04060001 00000000 000f000c 00000000 00000000 01040300 mptbase: ioc1: config_complete (mf=f7ec2480,mr=f7ec0300) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc1: Sending Config request type 0, page 2 and action 0 04060000 00000000 000f000d 00000000 00000000 20020700 mptbase: ioc1: config_complete (mf=f7ec24e0,mr=f7ec0340) IOCStatus=0000h, IOCLogInfo=00000000h mptbase: ioc1: Sending Config request type 0, page 2 and action 1 04060001 00000000 000f000e 00000000 00000000 00020700 mptbase: ioc1: config_complete (mf=f7ec2540,mr=f7ec0380) IOCStatus=0000h, IOCLogInfo=00000000h mptspi: ioc1: ScsiLookup @ f7e18c00, sz=1020 Targets @ c37bf180, sz=64 scsi5 : ioc1: LSI53C1030, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=19 00080000 00014006 000e000f 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 0 lun 0 max 255 00080001 00014006 000e0010 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 1 lun 0 max 255 00080002 00014006 000e0011 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 2 lun 0 max 255 00080003 00014006 000e0012 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 3 lun 0 max 255 00080004 00014006 000e0013 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 4 lun 0 max 255 00080005 00014006 000e0014 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 5 lun 0 max 255 00080006 00014006 000e0015 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 6 lun 0 max 255 00080008 00014006 000e0016 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 8 lun 0 max 255 00080009 00014006 000e0017 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 9 lun 0 max 255 0008000a 00014006 000e0018 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 10 lun 0 max 255 0008000b 00014006 000e0019 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 11 lun 0 max 255 0008000c 00014006 000e001a 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 12 lun 0 max 255 0008000d 00014006 000e001b 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 13 lun 0 max 255 0008000e 00014006 000e001c 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 14 lun 0 max 255 0008000f 00014006 000e001d 00430000 00000000 00000000 00000000 00000000 mptscsih: search_running target 15 lun 0 max 255 bound device '0000:0a:06.1' to driver 'mptspi' pci: Bound Device 0000:0a:06.1 to Driver mptspi Fusion MPT FC Host driver 3.03.04 mptfc: Registered for IOC reset notifications bus pci: add driver mptfc Fusion MPT SAS Host driver 3.03.04 mptsas: Registered for IOC reset notifications bus pci: add driver mptsas Fusion MPT misc device (ioctl) driver 3.03.04 mptctl: Registered with Fusion MPT base driver mptctl: /dev/mptctl @ (major,minor=10,220) mptctl: Registered for IOC reset notifications bus type 'ieee1394' registered bus pci: add driver ohci1394 pci: Matched Device 0000:01:05.0 with Driver ohci1394 ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org> ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 19 ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNK4] -> GSI 19 (level, high) -> IRQ 20 bus ieee1394: add device fw-host0 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[b0104000-b01047ff] Max Packet=[2048] bound device '0000:01:05.0' to driver 'ohci1394' pci: Bound Device 0000:01:05.0 to Driver ohci1394 ieee1394: raw1394: /dev/raw1394 device initialized bus ieee1394: add driver raw1394 usbmon: debugfs is not available bus pci: add driver ehci_hcd pci: Matched Device 0000:00:02.1 with Driver ehci_hcd ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS2] -> GSI 21 (level, high) -> IRQ 21 PCI: Setting latency timer of device 0000:00:02.1 to 64 ehci_hcd 0000:00:02.1: EHCI Host Controller ehci_hcd 0000:00:02.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:02.1 ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:02.1: irq 21, io mem 0xb0001000 ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 bus usb: add device usb1 bound device 'usb1' to driver 'usb' bus usb: add device 1-0:1.0 usb: Matched Device 1-0:1.0 with Driver hub hub 1-0:1.0: USB hub found hub 1-0:1.0: 10 ports detected bound device '1-0:1.0' to driver 'hub' usb: Bound Device 1-0:1.0 to Driver hub bound device '0000:00:02.1' to driver 'ehci_hcd' pci: Bound Device 0000:00:02.1 to Driver ehci_hcd USB Universal Host Controller Interface driver v2.3 bus pci: add driver uhci_hcd bus usb: add driver usblp usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... bus usb: add driver usb-storage usbcore: registered new driver usb-storage USB Mass Storage support registered. bus usb: add driver usbhid usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice bus serio: add driver atkbd serio: Matched Device serio0 with Driver atkbd NET: Registered protocol family 2 IP route cache hash table entries: 262144 (order: 8, 1048576 bytes) TCP established hash table entries: 262144 (order: 9, 3145728 bytes) TCP bind hash table entries: 65536 (order: 7, 786432 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered ip_conntrack version 2.4 (8192 buckets, 65536 max) - 212 bytes per conntrack serio: Matched Device serio1 with Driver atkbd input: AT Translated Set 2 keyboard as /class/input/input0 bound device 'serio1' to driver 'atkbd' serio: Bound Device serio1 to Driver atkbd bus serio: add driver psmouse serio: Matched Device serio0 with Driver psmouse ip_tables: (C) 2000-2002 Netfilter core team ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/ arp_tables: (C) 2002 David S. Miller TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Starting balanced_irq Using IPI Shortcut mode EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 224k freed kjournald starting. Commit interval 5 seconds bus ieee1394: add device 00e081000023a5ab ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e081000023a5ab] EXT3 FS on sda1, internal journal Linux agpgart interface v0.101 (c) Dave Jones bus type 'ac97' registered bus pci: add driver Intel ICH pci: Matched Device 0000:00:04.0 with Driver Intel ICH ACPI: PCI Interrupt Link [LACI] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LACI] -> GSI 20 (level, high) -> IRQ 22 PCI: Setting latency timer of device 0000:00:04.0 to 64 intel8x0_measure_ac97_clock: measured 58152 usecs intel8x0: clocking to 47044 bus ac97: add device card0-0 bound device '0000:00:04.0' to driver 'Intel ICH' pci: Bound Device 0000:00:04.0 to Driver Intel ICH bus type 'i2c' registered bus i2c: add driver i2c_adapter bus pci: add driver nForce2_smbus pci: Matched Device 0000:00:01.1 with Driver nForce2_smbus i2c_adapter i2c-0: nForce2 SMBus adapter at 0xa000 i2c_adapter i2c-1: nForce2 SMBus adapter at 0xa040 bound device '0000:00:01.1' to driver 'nForce2_smbus' pci: Bound Device 0000:00:01.1 to Driver nForce2_smbus
> You were right, indeed the pci=nommconf did the trick, the controller > was detected. OK, I guess you can turn off all the debug stuff we added. I copied Andi Kleen since he's been working in that area.
Guys, where do we stand on this bug now? Thanks.
> Guys, where do we stand on this bug now? Greg KH says there's a patch in the latest -mm that should take care of this issue. stathis, can you try 2.6.16-rc5 and see whether it's fixed there? If not, try 2.6.16-rc5-mm1 and we can at least make sure it's fixed there.
Hi, I tried 2.6.16-rc5 and it appears to be fixed. I do not know if it is important anymore, but I have not been able to use the -mm patch against the 2.6.15 tree, it complained about a few things and make failed afterwards. Am I doing something wrong (applying the patch against the wrong version)? There is no instructions as far as I can tell where to apply it, I assumed it is 2.6.15. Thanks for the help. Let me know if you want me to perform any other tests. --st
> I tried 2.6.16-rc5 and it appears to be fixed. Great! Thanks for all your testing. > I do not know if it is important anymore, but I have > not been able to use the -mm patch against the 2.6.15 tree ... I use the -mm patch all the time, and it generally works fine. So I suspect you're applying it against the wrong tree. For 2.6.16-rc5-mm1, you should: - unpack a 2.6.15 tree - apply the 2.6.16-rc5 patch - apply the 2.6.16-rc5-mm1 patch I use "ketchup," which does all this stuff automatically: http://www.selenic.com/ketchup/wiki/ For example: $ mkdir work-mm $ cd work-mm $ ketchup 2.6.16-rc5-mm1
Stathis, was your testing successful? Can you confirm the problem is fixed? Thanks.
(In reply to comment #29) > Stathis, was your testing successful? Can you confirm the problem is fixed? > Thanks. > I haven't had any issues since, I currently use 2.6.20 on gentoo (meaning with the distro's patches). My relevant kernel config reads: # Fusion MPT device support CONFIG_FUSION=y CONFIG_FUSION_SPI=y # CONFIG_FUSION_FC is not set # CONFIG_FUSION_SAS is not set CONFIG_FUSION_MAX_SGE=64 # CONFIG_FUSION_CTL is not set I remember testing vanilla sources back then and it also worked, so I'd say its fixed long ago.
Yes this was all sorted out a while ago. Thanks for confirming this.