I have the same problem on
Gentoo linux with kernel 2.6.15-rc1
Machine is: P4 3.2GHz HT enabled
2x e1000 cards

KERNEL: assertion (!sk->sk_forward_alloc) failed at net/core/stream.c (279)
KERNEL: assertion (!sk->sk_forward_alloc) failed at net/ipv4/af_inet.c (148)

Are you running jumbo frames (ie MTU > 1500)?

please include the information requested by REPORTING-BUGS at the base of the
kernel tree.

your .config, machine, e1000 information from lspci -vvv dmesg would all be
helpful.  A reproduction case also would help.

lspci->

00:00.0 Host bridge: Intel Corp. E7520 Memory Controller Hub (rev 09)
        Subsystem: Dell: Unknown device 016d
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0
        Capabilities: [40] #09 [4105]

00:02.0 PCI bridge: Intel Corp. E7525/E7520/E7320 PCI Express Port A (rev 09)
(prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0, cache line size 10
        Bus: primary=00, secondary=01, subordinate=03, sec-latency=0
        I/O behind bridge: 0000f000-00000fff
        Memory behind bridge: dfc00000-dfefffff
        Prefetchable memory behind bridge: 00000000d8000000-00000000d8000000
        Secondary status: SERR
        BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
                Address: fee00000  Data: 0000
        Capabilities: [64] #10 [0041]

00:04.0 PCI bridge: Intel Corp. E7525/E7520 PCI Express Port B (rev 09) (prog-if
00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0, cache line size 10
        Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
        I/O behind bridge: 0000f000-00000fff
        Memory behind bridge: fff00000-000fffff
        Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
        BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
                Address: fee00000  Data: 0000
        Capabilities: [64] #10 [0041]

00:05.0 PCI bridge: Intel Corp. E7520 PCI Express Port B1 (rev 09) (prog-if 00
[Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0, cache line size 10
        Bus: primary=00, secondary=05, subordinate=07, sec-latency=0
        I/O behind bridge: 0000d000-0000efff
        Memory behind bridge: df700000-dfbfffff
        Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
        BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
                Address: fee00000  Data: 0000
        Capabilities: [64] #10 [0041]

00:06.0 PCI bridge: Intel Corp. E7520 PCI Express Port C (rev 09) (prog-if 00
[Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0, cache line size 10
        Bus: primary=00, secondary=08, subordinate=0a, sec-latency=0
        I/O behind bridge: 0000c000-0000cfff
        Memory behind bridge: df400000-df6fffff
        Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
        BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
                Address: fee00000  Data: 0000
        Capabilities: [64] #10 [0041]

00:1d.0 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI Controller
#1 (rev 02) (prog-if 00 [UHCI])
        Subsystem: Dell: Unknown device 016d
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 4: I/O ports at ace0 [size=32]

00:1d.1 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI Controller
#2 (rev 02) (prog-if 00 [UHCI])
        Subsystem: Dell: Unknown device 016d
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 19
        Region 4: I/O ports at acc0 [size=32]

00:1d.2 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI Controller
#3 (rev 02) (prog-if 00 [UHCI])
        Subsystem: Dell: Unknown device 016d
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin C routed to IRQ 20
        Region 4: I/O ports at aca0 [size=32]

00:1d.7 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller
(rev 02) (prog-if 20 [EHCI])
        Subsystem: Dell: Unknown device 016d
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin D routed to IRQ 18
        Region 0: Memory at dff00000 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] #0a [20a0]

00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev c2) (prog-if 00 [Normal
decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=32
        I/O behind bridge: 0000b000-0000bfff
        Memory behind bridge: df200000-df3fffff
        Prefetchable memory behind bridge: d0000000-d7ffffff
        BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corp. 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge
(rev 02)
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

00:1f.1 IDE interface: Intel Corp. 82801EB/ER (ICH5/ICH5R) IDE Controller (rev
02) (prog-if 8a [Master SecP PriP])
        Subsystem: Dell: Unknown device 016d
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 0
        Region 0: I/O ports at <unassigned>
        Region 1: I/O ports at <unassigned>
        Region 2: I/O ports at <unassigned>
        Region 3: I/O ports at <unassigned>
        Region 4: I/O ports at fc00 [size=16]
        Region 5: Memory at d8100000 (32-bit, non-prefetchable) [size=1K]

01:00.0 PCI bridge: Intel Corp. 80332 [Dobson] I/O processor (A-Segment Bridge)
(rev 06) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0, cache line size 10
        Bus: primary=01, secondary=02, subordinate=02, sec-latency=64
        I/O behind bridge: 0000f000-00000fff
        Memory behind bridge: dfd00000-dfefffff
        Prefetchable memory behind bridge: 00000000d8000000-00000000d8000000
        BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
        Capabilities: [44] #10 [0071]
        Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [6c] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [d8] PCI-X non-bridge device.
                Command: DPERE+ ERO+ RBC=0 OST=4
                Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple,
DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
01:00.2 PCI bridge: Intel Corp. 80332 [Dobson] I/O processor (B-Segment Bridge)
(rev 06) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0, cache line size 10
        Bus: primary=01, secondary=03, subordinate=03, sec-latency=64
        I/O behind bridge: 0000f000-00000fff
        Memory behind bridge: fff00000-000fffff
        Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
        BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
        Capabilities: [44] #10 [0071]
        Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [6c] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [d8] PCI-X non-bridge device.
                Command: DPERE+ ERO+ RBC=0 OST=4
                Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple,
DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
02:0e.0 RAID bus controller: Dell PowerEdge Expandable RAID controller 4 (rev 06)
        Subsystem: Dell PowerEdge Expandable RAID Controller 4e/Di
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping+ SERR+ FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (32000ns min), cache line size 10
        Interrupt: pin A routed to IRQ 17
        Region 0: Memory at d80f0000 (32-bit, prefetchable) [size=64K]
        Region 2: Memory at dfdc0000 (32-bit, non-prefetchable) [size=256K]
        Expansion ROM at dfe00000 [disabled] [size=128K]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [d0] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [e0] PCI-X non-bridge device.
                Command: DPERE- ERO- RBC=0 OST=3
                Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple,
DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
05:00.0 PCI bridge: Intel Corp. 6700PXH PCI Express-to-PCI Bridge A (rev 09)
(prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0, cache line size 10
        Bus: primary=05, secondary=06, subordinate=06, sec-latency=32
        I/O behind bridge: 0000e000-0000efff
        Memory behind bridge: dfa00000-dfbfffff
        Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
        BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
        Capabilities: [44] #10 [0071]
        Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [6c] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [d8] PCI-X non-bridge device.
                Command: DPERE+ ERO+ RBC=0 OST=0
                Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple,
DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
05:00.2 PCI bridge: Intel Corp. 6700PXH PCI Express-to-PCI Bridge B (rev 09)
(prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0, cache line size 10
        Bus: primary=05, secondary=07, subordinate=07, sec-latency=32
        I/O behind bridge: 0000d000-0000dfff
        Memory behind bridge: df800000-df9fffff
        Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
        BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
        Capabilities: [44] #10 [0071]
        Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [6c] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [d8] PCI-X non-bridge device.
                Command: DPERE+ ERO+ RBC=0 OST=0
                Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple,
DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
06:07.0 Ethernet controller: Intel Corp. 82541GI Gigabit Ethernet Controller
(rev 05)
        Subsystem: Dell: Unknown device 016d
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (63750ns min), cache line size 10
        Interrupt: pin A routed to IRQ 21
        Region 0: Memory at dfae0000 (32-bit, non-prefetchable) [size=128K]
        Region 2: I/O ports at ecc0 [size=64]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [e4] PCI-X non-bridge device.
                Command: DPERE- ERO+ RBC=0 OST=0
                Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple,
DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
07:08.0 Ethernet controller: Intel Corp. 82541GI Gigabit Ethernet Controller
(rev 05)
        Subsystem: Dell: Unknown device 016d
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (63750ns min), cache line size 10
        Interrupt: pin A routed to IRQ 22
        Region 0: Memory at df8e0000 (32-bit, non-prefetchable) [size=128K]
        Region 2: I/O ports at dcc0 [size=64]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [e4] PCI-X non-bridge device.
                Command: DPERE- ERO+ RBC=0 OST=0
                Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple,
DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
08:00.0 PCI bridge: Intel Corp. 6700PXH PCI Express-to-PCI Bridge A (rev 09)
(prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0, cache line size 10
        Bus: primary=08, secondary=09, subordinate=09, sec-latency=64
        I/O behind bridge: 0000c000-0000cfff
        Memory behind bridge: df500000-df6fffff
        Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
        BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
        Capabilities: [44] #10 [0071]
        Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [6c] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [d8] PCI-X non-bridge device.
                Command: DPERE+ ERO+ RBC=0 OST=4
                Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple,
DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
08:00.2 PCI bridge: Intel Corp. 6700PXH PCI Express-to-PCI Bridge B (rev 09)
(prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
        Latency: 0, cache line size 10
        Bus: primary=08, secondary=0a, subordinate=0a, sec-latency=64
        I/O behind bridge: 0000f000-00000fff
        Memory behind bridge: fff00000-000fffff
        Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
        BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
        Capabilities: [44] #10 [0071]
        Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [6c] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [d8] PCI-X non-bridge device.
                Command: DPERE+ ERO+ RBC=0 OST=4
                Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple,
DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
09:04.0 Ethernet controller: Intel Corp. 82546EB Gigabit Ethernet Controller
(Copper) (rev 01)
        Subsystem: Intel Corp. PRO/1000 MT Dual Port Server Adapter
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (63750ns min), cache line size 10
        Interrupt: pin A routed to IRQ 23
        Region 0: Memory at df5e0000 (64-bit, non-prefetchable) [size=128K]
        Region 4: I/O ports at ccc0 [size=64]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [e4] PCI-X non-bridge device.
                Command: DPERE- ERO+ RBC=0 OST=0
                Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple,
DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-      Capabilities: [f0] Message Signalled
Interrupts: 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000

09:04.1 Ethernet controller: Intel Corp. 82546EB Gigabit Ethernet Controller
(Copper) (rev 01)
        Subsystem: Intel Corp. PRO/1000 MT Dual Port Server Adapter
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (63750ns min), cache line size 10
        Interrupt: pin B routed to IRQ 24
        Region 0: Memory at df5c0000 (64-bit, non-prefetchable) [size=128K]
        Region 4: I/O ports at cc80 [size=64]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [e4] PCI-X non-bridge device.
                Command: DPERE- ERO+ RBC=0 OST=0
                Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple,
DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-      Capabilities: [f0] Message Signalled
Interrupts: 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000

0b:0d.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY [Radeon
7000/VE] (prog-if 00 [VGA])
        Subsystem: Dell: Unknown device 016d
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr-
Stepping+ SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (2000ns min), cache line size 10
        Interrupt: pin A routed to IRQ 7
        Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
        Region 1: I/O ports at bc00 [size=256]
        Region 2: Memory at df2f0000 (32-bit, non-prefetchable) [size=64K]
        Expansion ROM at df200000 [disabled] [size=128K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

yes, jumbo frames == 1500

Get the same assertions but no page allocation failure after that.

Linux version 2.6.14.3 (root@nostromo) (gcc version 3.3.1) #2 SMP Wed Dec 14
13:40:06 CET 2005

Hardware: Dual Athlon XP 2600+ (2000MHz), On-Board Intel e1000, 3ware IDE.
Software: Diablo, Exim.
Kernel without module support.
No Jumbo Frames here.

00:0b.0 Ethernet controller: Intel Corp. 82545EM Gigabit Ethernet Controller
(Copper) (rev 01)
        Subsystem: Intel Corp. PRO/1000 MT Server Adapter
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
        Latency: 64 (63750ns min), cache line size 10
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at f4800000 (32-bit, non-prefetchable) [size=128K]
        Region 2: I/O ports at 1000 [size=64]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [e4] PCI-X non-bridge device.
                Command: DPERE- ERO+ RBC=0 OST=0
                Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple,
DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-      Capabilities: [f0] Message Signalled
Interrupts: 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000

I'm having a similar problem with kernel 2.6.14.2. I've recently upgraded one of
my boxes to 2.6.15 and it's still happening. I get the kernel assertion messages
but no page allocation failures. Unlike Sebastian and Geno my boxes are using
the TG3 driver for a Broadcom adapter. 

Distribution: Gentoo Linux

Hardware: 2x x86_64 Dual Core AMD Opteron(tm) Processor 270 AuthenticAMD
          NetXtreme BCM5704 Gigabit Ethernet (rev 03)
          8GB RAM

Software: Sun JDK 1.5.0_06-b05
          Resin 2.1.17
          ColdFusion MX6

No Jumbo Frames

--------------------------------------------------------------------------------
ethtool:
  rx-checksumming: on
  tx-checksumming: on
  scatter-gather: on
  tcp segmentation offload: on
--------------------------------------------------------------------------------

lspci:
Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet
(rev 03)
        Subsystem: Broadcom Corporation Unknown device 1644
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (16000ns min), Cache Line Size 10
        Interrupt: pin A routed to IRQ 177
        Region 0: Memory at fc8b0000 (64-bit, non-prefetchable) [size=64K]
        Region 2: Memory at fc8a0000 (64-bit, non-prefetchable) [size=64K]
        Expansion ROM at fc890000 [disabled] [size=64K]
        Capabilities: [40] PCI-X non-bridge device
                Command: DPERE- ERO- RBC=2048 OST=1
                Status: Dev=02:09.0 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
        Capabilities: [50] Vital Product Data
        Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
                Address: baf3c41433412018  Data: 9ad4
--------------------------------------------------------------------------------

dmesg:
Bootdata ok (command line is root=/dev/md1)
Linux version 2.6.15 (root@ompi-2) (gcc version 3.4.4 (Gentoo 3.4.4-r1,
ssp-3.4.4-1.0, pie-8.7.8)) #1 SMP Fri Jan 6 17:28:06 EST 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
 BIOS-e820: 000000007fff0000 - 000000007ffff000 (ACPI data)
 BIOS-e820: 000000007ffff000 - 0000000080000000 (ACPI NVS)
 BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
 BIOS-e820: 0000000100000000 - 0000000280000000 (usable)
ACPI: RSDP (v002 ACPIAM                                ) @ 0x00000000000f6d70
ACPI: XSDT (v001 A M I  OEMXSDT  0x10000611 MSFT 0x00000097) @ 0x000000007fff0100
ACPI: FADT (v001 A M I  OEMFACP  0x10000611 MSFT 0x00000097) @ 0x000000007fff0281
ACPI: MADT (v001 A M I  OEMAPIC  0x10000611 MSFT 0x00000097) @ 0x000000007fff0380
ACPI: OEMB (v001 A M I  OEMBIOS  0x10000611 MSFT 0x00000097) @ 0x000000007ffff040
ACPI: SRAT (v001 A M I  OEMSRAT  0x10000611 MSFT 0x00000097) @ 0x000000007fff3b10
ACPI: HPET (v001 A M I  OEMHPET  0x10000611 MSFT 0x00000097) @ 0x000000007fff3c20
ACPI: ASF! (v001 AMIASF AMDSTRET 0x00000001 INTL 0x02002026) @ 0x000000007fff3c60
ACPI: DSDT (v001  0AAAA 0AAAA000 0x00000000 INTL 0x02002026) @ 0x0000000000000000
SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: PXM 0 -> APIC 1 -> Node 0
SRAT: PXM 1 -> APIC 2 -> Node 1
SRAT: PXM 1 -> APIC 3 -> Node 1
SRAT: Node 0 PXM 0 100000-80000000
SRAT: Node 1 PXM 1 180000000-280000000
SRAT: Node 0 PXM 0 100000-180000000
SRAT: Node 0 PXM 0 0-180000000
Using 31 for the hash shift.
Bootmem setup node 0 0000000000000000-0000000180000000
Bootmem setup node 1 0000000180000000-0000000280000000
On node 0 totalpages: 1025836
  DMA zone: 2820 pages, LIFO batch:0
  DMA32 zone: 505896 pages, LIFO batch:31
  Normal zone: 517120 pages, LIFO batch:31
  HighMem zone: 0 pages, LIFO batch:0
On node 1 totalpages: 1034240
  DMA zone: 0 pages, LIFO batch:0
  DMA32 zone: 0 pages, LIFO batch:0
  Normal zone: 1034240 pages, LIFO batch:31
  HighMem zone: 0 pages, LIFO batch:0
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
Processor #2 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
Processor #3 15:1 APIC version 16
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x05] address[0xfebff000] gsi_base[24])
IOAPIC[1]: apic_id 5, version 17, address 0xfebff000, GSI 24-27
ACPI: IOAPIC (id[0x06] address[0xfebfe000] gsi_base[28])
IOAPIC[2]: apic_id 6, version 17, address 0xfebfe000, GSI 28-31
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x102282a0 base: 0xfec01000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7f780000)
Checking aperture...
CPU 0: aperture @ f8000000 size 64 MB
CPU 1: aperture @ f8000000 size 64 MB
Built 2 zonelists
Kernel command line: root=/dev/md1
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 14.318180 MHz HPET timer.
time.c: Detected 1991.154 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
Memory: 8227472k/10485760k available (2856k kernel code, 160684k reserved, 990k
data, 220k init)
Calibrating delay using timer specific routine.. 3986.34 BogoMIPS (lpj=19931710)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0(2) -> Node 0 -> Core 0
mtrr: v2.0 (20020519)
Using local APIC timer interrupts.
Detected 12.444 MHz APIC timer.
Booting processor 1/4 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3981.56 BogoMIPS (lpj=19907842)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1(2) -> Node 0 -> Core 1
Dual Core AMD Opteron(tm) Processor 270 stepping 02
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 582 cycles)
Booting processor 2/4 APIC 0x2
Initializing CPU#2
Calibrating delay using timer specific routine.. 3981.47 BogoMIPS (lpj=19907381)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 2(2) -> Node 1 -> Core 0
Dual Core AMD Opteron(tm) Processor 270 stepping 02
CPU 2: Syncing TSC to CPU 0.
CPU 2: synchronized TSC with CPU 0 (last diff -2 cycles, maxerr 1047 cycles)
Booting processor 3/4 APIC 0x3
Initializing CPU#3
Calibrating delay using timer specific routine.. 3981.47 BogoMIPS (lpj=19907385)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 3(2) -> Node 1 -> Core 1
Dual Core AMD Opteron(tm) Processor 270 stepping 02
CPU 3: Syncing TSC to CPU 0.
CPU 3: synchronized TSC with CPU 0 (last diff -70 cycles, maxerr 972 cycles)
Brought up 4 CPUs
time.c: Using HPET based timekeeping.
testing NMI watchdog ... OK.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:03:06.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
hpet0: at MMIO 0xfec01000 (virtual 0xffffffffff5fe000), IRQs 2, 8, 0
hpet0: 3 32-bit timers, 14318180 Hz
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ f8000000 size 65536 KB
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
pnp: 00:07: ioport range 0x680-0x6ff has been reserved
pnp: 00:07: ioport range 0x295-0x296 has been reserved
PCI: Bridge: 0000:00:06.0
  IO window: 9000-bfff
  MEM window: fc900000-feafffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0a.0
  IO window: 7000-8fff
  MEM window: fc600000-fc8fffff
  PREFETCH window: ff500000-ff5fffff
PCI: Bridge: 0000:00:0b.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
SGI XFS with large block/inode numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered
PCI: MSI quirk detected. pci_msi_quirk set.
PCI: MSI quirk detected. pci_msi_quirk set.
ACPI: Processor [CPU1] (supports 8 throttling states)
Real Time Clock Driver v1.12
hpet_resources: 0xfec01000 is busy
hw_random: AMD768 system management I/O registers at 0x1000.
hw_random hardware driver 1.0.0 loaded
Linux agpgart interface v0.101 (c) Dave Jones
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
serial8250: ttyS0 at I/O 0x3f8 (irq = 0) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 0) is a 16550A
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
loop: loaded (max 8 devices)
e100: Intel(R) PRO/100 Network Driver, 3.4.14-k4-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:03:08.0[A] -> GSI 18 (level, low) -> IRQ 169
e100: eth0: e100_probe: addr 0xfeafb000, irq 169, MAC addr 00:E0:81:2F:8C:4F
tg3.c:v3.47 (Dec 28, 2005)
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 24 (level, low) -> IRQ 177
eth1: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit)
10/100/1000BaseT Ethernet 00:e0:81:2f:8e:ee
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth1: dma_rwctrl[769f4000]
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI Interrupt 0000:02:09.1[B] -> GSI 25 (level, low) -> IRQ 185
eth2: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit)
10/100/1000BaseT Ethernet 00:e0:81:2f:8e:ef
eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth2: dma_rwctrl[769f4000]
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AMD8111: IDE controller at PCI slot 0000:00:07.1
AMD8111: chipset revision 3
AMD8111: not 100% native mode: will probe irqs later
AMD8111: 0000:00:07.1 (rev 03) UDMA133 controller
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: QSI CD-ROM SCR-242, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 24 (level, low) -> IRQ 177
scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.11
        <Adaptec AIC7902 Ultra320 SCSI adapter>
        aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs

  Vendor: SEAGATE   Model: ST336753LC        Rev: 0006
  Type:   Direct-Access                      ANSI SCSI revision: 03
 target0:0:0: asynchronous.
scsi0:A:0:0: Tagged Queuing enabled.  Depth 64
 target0:0:0: Beginning Domain Validation
 target0:0:0: wide asynchronous.
 target0:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM RTI WRFLOW PCOMP
(6.25 ns, offset 63)
 target0:0:0: Ending Domain Validation
  Vendor: SEAGATE   Model: ST336753LC        Rev: 0006
  Type:   Direct-Access                      ANSI SCSI revision: 03
 target0:0:1: asynchronous.
scsi0:A:1:0: Tagged Queuing enabled.  Depth 64
 target0:0:1: Beginning Domain Validation
 target0:0:1: wide asynchronous.
 target0:0:1: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM RTI WRFLOW PCOMP
(6.25 ns, offset 63)
 target0:0:1: Ending Domain Validation
  Vendor: SEAGATE   Model: ST336753LC        Rev: 0006
  Type:   Direct-Access                      ANSI SCSI revision: 03
 target0:0:2: asynchronous.
scsi0:A:2:0: Tagged Queuing enabled.  Depth 64
 target0:0:2: Beginning Domain Validation
 target0:0:2: wide asynchronous.
 target0:0:2: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM RTI WRFLOW PCOMP
(6.25 ns, offset 63)
 target0:0:2: Ending Domain Validation
  Vendor: SEAGATE   Model: ST336753LC        Rev: 0006
  Type:   Direct-Access                      ANSI SCSI revision: 03
 target0:0:3: asynchronous.
scsi0:A:3:0: Tagged Queuing enabled.  Depth 64
 target0:0:3: Beginning Domain Validation
 target0:0:3: wide asynchronous.
 target0:0:3: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM RTI WRFLOW PCOMP
(6.25 ns, offset 63)
 target0:0:3: Ending Domain Validation
ACPI: PCI Interrupt 0000:02:06.1[B] -> GSI 25 (level, low) -> IRQ 185
scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.11
        <Adaptec AIC7902 Ultra320 SCSI adapter>
        aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs

  Vendor: SEAGATE   Model: ST336753LC        Rev: 0006
  Type:   Direct-Access                      ANSI SCSI revision: 03
 target1:0:4: asynchronous.
scsi1:A:4:0: Tagged Queuing enabled.  Depth 64
 target1:0:4: Beginning Domain Validation
 target1:0:4: wide asynchronous.
 target1:0:4: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM RTI WRFLOW PCOMP
(6.25 ns, offset 63)
 target1:0:4: Ending Domain Validation
  Vendor: SEAGATE   Model: ST336753LC        Rev: 0006
  Type:   Direct-Access                      ANSI SCSI revision: 03
 target1:0:5: asynchronous.
scsi1:A:5:0: Tagged Queuing enabled.  Depth 64
 target1:0:5: Beginning Domain Validation
 target1:0:5: wide asynchronous.
 target1:0:5: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM RTI WRFLOW PCOMP
(6.25 ns, offset 63)
 target1:0:5: Ending Domain Validation
  Vendor: SEAGATE   Model: ST336753LC        Rev: 0006
  Type:   Direct-Access                      ANSI SCSI revision: 03
 target1:0:14: asynchronous.
scsi1:A:14:0: Tagged Queuing enabled.  Depth 64
 target1:0:14: Beginning Domain Validation
 target1:0:14: wide asynchronous.
 target1:0:14: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM RTI WRFLOW PCOMP
(6.25 ns, offset 63)
 target1:0:14: Ending Domain Validation
  Vendor: SEAGATE   Model: ST336753LC        Rev: 0006
  Type:   Direct-Access                      ANSI SCSI revision: 03
 target1:0:15: asynchronous.
scsi1:A:15:0: Tagged Queuing enabled.  Depth 64
 target1:0:15: Beginning Domain Validation
 target1:0:15: wide asynchronous.
 target1:0:15: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM RTI WRFLOW PCOMP
(6.25 ns, offset 63)
 target1:0:15: Ending Domain Validation
libata version 1.20 loaded.
sata_sil 0000:03:05.0: version 0.9
GSI 19 sharing vector 0xC1 and IRQ 19
ACPI: PCI Interrupt 0000:03:05.0[A] -> GSI 19 (level, low) -> IRQ 193
ata1: SATA max UDMA/100 cmd 0xFFFFC20000010C80 ctl 0xFFFFC20000010C8A bmdma
0xFFFFC20000010C00 irq 193
ata2: SATA max UDMA/100 cmd 0xFFFFC20000010CC0 ctl 0xFFFFC20000010CCA bmdma
0xFFFFC20000010C08 irq 193
ata3: SATA max UDMA/100 cmd 0xFFFFC20000010E80 ctl 0xFFFFC20000010E8A bmdma
0xFFFFC20000010E00 irq 193
ata4: SATA max UDMA/100 cmd 0xFFFFC20000010EC0 ctl 0xFFFFC20000010ECA bmdma
0xFFFFC20000010E08 irq 193
ata1: no device found (phy stat 00000000)
scsi2 : sata_sil
ata2: no device found (phy stat 00000000)
scsi3 : sata_sil
ata3: no device found (phy stat 00000000)
scsi4 : sata_sil
ata4: no device found (phy stat 00000000)
scsi5 : sata_sil
SCSI device sda: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sdb: drive cache: write back
 sdb: unknown partition table
sd 0:0:1:0: Attached scsi disk sdb
SCSI device sdc: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sdc: drive cache: write back
SCSI device sdc: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sdc: drive cache: write back
 sdc: unknown partition table
sd 0:0:2:0: Attached scsi disk sdc
SCSI device sdd: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sdd: drive cache: write back
SCSI device sdd: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sdd: drive cache: write back
 sdd: unknown partition table
sd 0:0:3:0: Attached scsi disk sdd
SCSI device sde: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sde: drive cache: write back
SCSI device sde: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sde: drive cache: write back
 sde: sde1 sde2 sde3
sd 1:0:4:0: Attached scsi disk sde
SCSI device sdf: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sdf: drive cache: write back
SCSI device sdf: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sdf: drive cache: write back
 sdf: unknown partition table
sd 1:0:5:0: Attached scsi disk sdf
SCSI device sdg: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sdg: drive cache: write back
SCSI device sdg: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sdg: drive cache: write back
 sdg: unknown partition table
sd 1:0:14:0: Attached scsi disk sdg
SCSI device sdh: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sdh: drive cache: write back
SCSI device sdh: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sdh: drive cache: write back
 sdh: unknown partition table
sd 1:0:15:0: Attached scsi disk sdh
mice: PS/2 mouse device common for all mice
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: automatically using best checksumming function: generic_sse
   generic_sse:  6093.600 MB/sec
raid5: using function: generic_sse (6093.600 MB/sec)
md: multipath personality registered as nr 7
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
oprofile: using NMI interrupt.
Netfilter messages via NETLINK v0.30.
NET: Registered protocol family 2
IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 312 bytes per conntrack
input: AT Translated Set 2 keyboard as /class/input/input0
ctnetlink v0.90: registering with nfnetlink.
ip_tables: (C) 2000-2002 Netfilter core team
arp_tables: (C) 2002 David S. Miller
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
powernow-k8: Found 4 AMD Athlon 64 / Opteron processors (version 1.50.4)
powernow-k8:    0 : fid 0xc (2000 MHz), vid 0x8 (1350 mV)
powernow-k8:    1 : fid 0xa (1800 MHz), vid 0x8 (1350 mV)
cpu_init done, current fid 0xc, vid 0x8
powernow-k8:    0 : fid 0xc (2000 MHz), vid 0x8 (1350 mV)
powernow-k8:    1 : fid 0xa (1800 MHz), vid 0x8 (1350 mV)
cpu_init done, current fid 0xc, vid 0x8
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sde3 ...
md:  adding sde3 ...
md: sde2 has different UUID to sde3
md: sde1 has different UUID to sde3
md:  adding sda3 ...
md: sda2 has different UUID to sde3
md: sda1 has different UUID to sde3
md: created md2
md: bind<sda3>
md: bind<sde3>
md: running: <sde3><sda3>
raid1: raid set md2 active with 2 out of 2 mirrors
md: considering sde2 ...
md:  adding sde2 ...
md: sde1 has different UUID to sde2
md:  adding sda2 ...
md: sda1 has different UUID to sde2
md: created md1
md: bind<sda2>
md: bind<sde2>
md: running: <sde2><sda2>
raid1: raid set md1 active with 2 out of 2 mirrors
md: considering sde1 ...
md:  adding sde1 ...
md:  adding sda1 ...
md: created md0
md: bind<sda1>
md: bind<sde1>
md: running: <sde1><sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
md: ... autorun DONE.
ReiserFS: md1: found reiserfs format "3.6" with standard journal
ReiserFS: md1: using ordered data mode
ReiserFS: md1: journal params: device md1, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md1: checking transaction log (md1)
ReiserFS: md1: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 220k freed
cdrom: open failed.
Adding 1598392k swap on /dev/md2.  Priority:-1 extents:1 across:1598392k
md: md3 stopped.
md: bind<sdc>
md: bind<sdf>
md: bind<sdb>
md3: setting max_sectors to 128, segment boundary to 32767
raid0: looking at sdb
raid0:   comparing sdb(35843584) with sdb(35843584)
raid0:   END
raid0:   ==> UNIQUE
raid0: 1 zones
raid0: looking at sdf
raid0:   comparing sdf(35843584) with sdb(35843584)
raid0:   EQUAL
raid0: looking at sdc
raid0:   comparing sdc(35843584) with sdb(35843584)
raid0:   EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 107530752 blocks.
raid0 : conf->hash_spacing is 107530752 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 8 bytes for hash.
md: md4 stopped.
md: bind<sdd>
md: bind<sdh>
md: bind<sdg>
md4: setting max_sectors to 128, segment boundary to 32767
raid0: looking at sdg
raid0:   comparing sdg(35843584) with sdg(35843584)
raid0:   END
raid0:   ==> UNIQUE
raid0: 1 zones
raid0: looking at sdh
raid0:   comparing sdh(35843584) with sdg(35843584)
raid0:   EQUAL
raid0: looking at sdd
raid0:   comparing sdd(35843584) with sdg(35843584)
raid0:   EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 107530752 blocks.
raid0 : conf->hash_spacing is 107530752 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 8 bytes for hash.
cdrom: open failed.
XFS mounting filesystem md3
Ending clean XFS mount for filesystem: md3
XFS mounting filesystem md4
Ending clean XFS mount for filesystem: md4
tg3: eth1: Link is up at 1000 Mbps, full duplex.
tg3: eth1: Flow control is on for TX and on for RX.
tg3: eth2: Link is up at 1000 Mbps, full duplex.
tg3: eth2: Flow control is on for TX and on for RX.
tg3: eth1: Link is up at 1000 Mbps, full duplex.
tg3: eth1: Flow control is on for TX and on for RX.
KERNEL: assertion (!sk->sk_forward_alloc) failed at net/core/stream.c (279)
KERNEL: assertion (!sk->sk_forward_alloc) failed at net/ipv4/af_inet.c (148)
... (additional kernel assertion messages removed for brevity) ...

This is a duplicate of the e1000 bug fixed in 2.6.16

*** This bug has been marked as a duplicate of 5946 ***